JVC KD-SX875 User manual

Category
Car video systems
Type
User manual

This manual is also suitable for

ENGLISH
GET0020-001A
[U]
For customer Use:
Enter below the Model No. and
Serial No. which are located on
the top or bottom of the cabinet.
Retain this information for future
reference.
Model No.
Serial No.
CD RECEIVER KD-SX975/KD-SX875
8 9 10 11 127
SCAN
MO
INT
DISP
SCM
8 9 10 11 127
SCAN
MO
INT
DISP
SCM
4V OUT
KD-SX875
KD-SX975
CD  !" KD-SX975/KD-SX875
∂“¥„Ë´’¥ KD-SX975/KD-SX875
INSTRUCTIONS
 !"
§”·π–π”
For installation and connections, refer to the separate manual.
 !"#$%&'()*+,-./0
°√ÿ≥“¥Ÿ§ŸË¡◊Õ∑’Ë·¬°µË“ßÀ“° „π°“√µ‘¥µ—Èß·≈–°“√‡™◊ËÕ¡µËÕ
‰∑¬
coverKD-SX975/SX875[U] 18/1/01, 08:533
2
ENGLISH
How to reset your unit
After detaching the control panel, press
the reset button on the panel holder using a
ball-point pen or similar tool.
This will reset the built-in microcomputer.
Note:
Your preset adjustments – such as preset
channels or sound adjustments will also
be erased.
BEFORE USE
*
For safety....
Do not raise the volume level too much, as this
will block outside sounds, making driving
dangerous.
Stop the car before performing any complicated
operations.
*
Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
EN02-05KD-SX975/SX875[U]f 18/1/01, 08:562
3
ENGLISH
To be continued on the next page
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to
ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
How to reset your unit .................................................................... 2
BASIC OPERATIONS .................................................... 5
RADIO OPERATIONS ................................................... 6
Listening to the radio ..................................................................... 6
Storing stations in memory ............................................................ 7
FM station automatic preset: SSM .............................................. 7
Manual preset .............................................................................. 8
Tuning into a preset station ........................................................... 9
Other convenient tuner functions ............................................... 10
Scanning broadcast stations ..................................................... 10
Selecting FM reception sound ................................................... 10
CD OPERATIONS ...................................................... 11
Playing a CD ................................................................................. 11
Locating a track or a particular portion on a CD ..................... 12
Selecting CD playback modes ..................................................... 13
Prohibiting CD ejection ............................................................... 14
SOUND ADJUSTMENTS ............................................. 15
Adjusting the sound ...................................................................... 15
Turning on/off the BBE
II
function ............................................... 16
Using the Sound Control Memory (SCM).................................. 17
Storing your own sound adjustments ......................................... 19
OTHER MAIN FUNCTIONS ......................................... 20
Setting the clock ............................................................................ 20
Changing the general settings (PSM) ........................................ 21
Basic Procedure ........................................................................ 21
Canceling Advanced SCM ......................................................... 23
Selecting the level display ......................................................... 23
Selecting the dimmer mode (ONLY FOR KD-SX975) ............... 24
Turning on/off the key-touch tone .............................................. 24
Selecting the telephone muting ................................................. 25
Selecting the external component to use .................................. 25
Detaching the control panel ......................................................... 26
REMOTE OPERATIONS .............................................. 27
Installing the battery .................................................................... 27
Using the remote controller ......................................................... 28
EN02-05KD-SX975/SX875[U]f 18/1/01, 08:563
4
ENGLISH
CD CHANGER OPERATIONS ...................................... 29
Playing CDs ................................................................................... 29
Selecting CD playback modes ..................................................... 31
EXTERNAL COMPONENT OPERATIONS ...................... 32
Playing an external component ................................................... 32
MAINTENANCE ........................................................ 33
Handling CDs ................................................................................ 33
TROUBLESHOOTING ................................................. 34
SPECIFICATIONS ....................................................... 35
EN02-05KD-SX975/SX875[U]f 18/1/01, 08:564
5
ENGLISH
BASIC OPERATIONS
1
Turn on the power.
“HELLO” appears on the display.
2
Select the source.
To operate the tuner, see pages 6 – 10.
To operate the CD player, see pages 11 – 14.
To operate the CD changer, see pages 29 – 31.
To operate the external component, see page 32.
3
Adjust the volume.
4
Adjust the sound as you want (see pages 15 – 19).
To drop the volume in a moment
Press briefly while listening to any source. ATT starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the button briefly again.
To turn off the power
Press for more than 1 second. SEE YOU appears, then the unit turns off.
Note on One-Touch Operation:
When you select a source in step 2 below, the power automatically comes on.
You do not have to press this button to turn on the power.
CAUTION on Volume Setting
CDs produces very little noise compared with other sources. If the volume level is adjusted for the
tuner, for example, the speakers may be damaged by the sudden increase in the output level.
Therefore, lower the volume before playing a CD and adjust it as required during playback.
1
32
Note:
When you use this unit for the
first time, set the built-in clock
correctly, see page 20.
Volume level appears
Volume level indicator
EN02-05KD-SX975/SX875[U]f 18/1/01, 08:565
6
ENGLISH
RADIO OPERATIONS
Listening to the radio
1
Select the band (FM1, FM2, FM3 or AM).
You can select any one of FM1, FM2, and FM3 to listen to an
FM station.
2
Start searching a station.
While searching stations, “SEEK” appears on
the display.
When a station is received, searching stops.
To stop searching before a station is received, press the same button you have pressed
for searching.
To tune in a particular frequency without searching
1 Press FM/AM repeatedly to select the band (FM or AM).
2 Press and hold ¢
or 4 until “MANU (manual)” starts flashing on the display.
Now you can manually change the frequency while “MANU” is flashing.
3 Press ¢
or 4 repeatedly until the frequency you want is reached.
If you hold down the button, the frequency keeps changing until you release the button.
FM1 FM2 FM3
AM
Audio (see page 23) or
volume level indicator.
Selected band appears.
To search stations
of higher
frequencies.
12
To search stations
of lower
frequencies.
EN06-10KD-SX975/SX875[U]f 18/1/01, 08:596
7
ENGLISH
1
Select the FM band number (FM1, FM2 or
FM3) you want to store FM stations into.
2
Press and hold both buttons for more than
2 seconds.
Local FM stations with the strongest signals are searched and stored automatically in the
band number you have selected (FM1, FM2 or FM3). These stations are preset in the number
buttons — No. 1 (lowest frequency) to No. 6 (highest frequency).
When automatic preset is over, the station stored in number button 1 will be automatically
tuned in.
Storing stations in memory
You can use one of the following two methods to store broadcasting stations in memory.
Automatic preset of FM stations: SSM (Strong-station Sequential Memory)
Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band (FM1, FM2 and FM3).
FM1 FM2 FM3
AM
“SSM” appears, then disappears when
automatic preset is over.
12
EN06-10KD-SX975/SX875[U]f 18/1/01, 08:597
8
ENGLISH
1
Select the FM1 band.
2
Tune into a station of 88.3 MHz.
See page 6 to tune into a station.
3
Press and hold the number button (in this
example, 1) for more than 2 seconds.
4
Repeat the above procedure to store other
stations into other preset numbers.
Notes:
A previously preset station is erased when a new station is stored in the same preset number.
Preset stations are erased when the power supply to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset the stations again.
Manual preset
You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually.
EXAMPLE: Storing an FM station of 88.3 MHz into the preset number 1 of the FM1 band
132
Selected band and “MEMO”
flash alternately for a while.
EN06-10KD-SX975/SX875[U]f 18/1/01, 08:598
9
ENGLISH
Tuning into a preset station
You can easily tune into a preset station.
Remember that you must store stations first. If you have not stored them yet, see pages 7
and 8.
1
Select the band (FM1, FM2, FM3 or AM)
you want.
2
Select the number (1 – 6) for the preset station
you want.
12
FM1 FM2 FM3
AM
EN06-10KD-SX975/SX875[U]f 18/1/01, 08:599
10
ENGLISH
Scanning broadcast stations
When you press SCAN/RPT (Scan/Repeat) while listening to the radio, station scanning
starts. Each time a broadcast is tuned in, scanning stops for about 5 seconds (“SCAN” flashes
on the display), and you can check what program is now being broadcast.
If you want to listen to that program, press the same button again to stop scanning.
Selecting FM reception sound
When an FM stereo broadcast is hard to receive:
Press MO/RND (Mono/Random) while listening to an FM stereo broadcast. The MONO
indicator lights up on the display.
The sound you hear becomes monaural but reception will be improved.
To restore the stereo effect, press the same button again.
Other convenient tuner functions
SCAN/RPT
MO/RND
MO
Lights up when receiving an FM broadcast in stereo.
EN06-10KD-SX975/SX875[U]f 18/1/01, 08:5910
11
ENGLISH
CD OPERATIONS
Playing a CD
1
Open the control panel.
2
1. Insert a disc into the loading slot.
The unit turns on, draws a CD and starts playback
automatically.
2. Close the control panel by hand.
1
Notes:
When a CD is inserted up side down, “PLEASE” and “EJECT” appear on the display alternately.
When you open the control panel by pressing 0, the CD automatically ejects.
Note on One-Touch Operation:
When a CD is already in the loading slot, pressing CD turns on the unit and starts playback
automatically.
To stop play and eject the CD
Press 0.
CD play stops, the control panel opens, then the CD automatically ejects from the loading slot.
If you change the source to FM, AM, CD changer or external component, the CD play also
stops (without ejecting the CD this time).
If the ejected disc is not removed for about 15 seconds, the disc is automatically inserted again into
the loading slot to protect it from dust. (CD play will not start this time.)
You can eject the CD even when the unit is turned off.
Total track number
of the inserted disc
Elapsed
playing time
Current track
Total playing time of
the inserted disc
EN11-14KD-SX975/SX875[U]f-2 19/1/01, 21:0511
12
ENGLISH
To fast-forward or reverse the track
Press and hold
¢ , while playing a CD, to fast-forward the track.
Press and hold 4
, while playing a CD, to reverse the track.
To go to the next tracks or the previous tracks
Press
¢ briefly, while playing a CD, to go ahead to the beginning of
the next track. Each time you press the button consecutively, the beginning
of the next tracks is located and played back.
Press
4 briefly, while playing a CD, to go back to the beginning of
the current track. Each time you press the button consecutively, the
beginning of the previous tracks is located and played back.
To go to a particular track directly
Press the number button corresponding to the track number to start its
playback.
To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1 second.
Locating a track or a particular portion on a CD
Number buttons
¢
4
EN11-14KD-SX975/SX875[U]f-2 19/1/01, 21:0512
13
ENGLISH
Selecting CD playback modes
SCAN/RPT MO/RND
To play back tracks at random (Random Play)
You can play back all tracks on the CD at random.
Each time you press MO/RND (Mono/Random) while playing a CD, CD
random play mode turns on and off alternately.
When the random mode is turned on, the RND indicator lights up on the
display and a track randomly selected starts playing.
To play back tracks repeatedly (Repeat Play)
You can play back the current track repeatedly.
Each time you press SCAN/RPT (Scan/Repeat) while playing a CD, CD
repeat play mode turns on and off alternately.
When the repeat mode is turned on, the RPT indicator lights up on the
display.
MO
SCAN
Track number of the currently playing track
EN11-14KD-SX975/SX875[U]f-2 19/1/01, 21:0513
14
ENGLISH
Prohibiting CD ejection
You can prohibit CD ejection and can lock a CD in the loading slot.
While pressing CD, press and hold
for more than 2 seconds. NO EJECT flashes
on the display for about 5 seconds, and the CD is locked and cannot be ejected.
To cancel the prohibition and unlock the CD, press
again for more than 2 seconds,
while pressing CD. EJECT OK flashes on the display for about 5 seconds, and the CD is
unlocked.
To play back only intros (Intro Scan)
Each time you press INT (Intro) briefly while playing a CD, CD intro scan
mode turns on and off alternately.
When the intro scan mode is turned on, INT appears on the display for 5
seconds and the track number flashes. The first 15 seconds of each track
are played sequentially.
INT
Track number of the currently playing track
INT
EN11-14KD-SX975/SX875[U]f-2 19/1/01, 21:0514
ENGLISH
15
1
Select the item you want to adjust.
Indication To do: Range
BAS Adjust the bass –06 (min.) — +06 (max.)
(Bass)
TRE Adjust the treble –06 (min.) — +06 (max.)
(Treble)
FAD Adjust the front and rear speaker R06 (rear only) — F06 (front only)
(Fader)* balance
BAL Adjust the left and right speaker L06 (left only) — R06 (right only)
(Balance) balance
VOL Adjust the volume 00 (min.) — 50 (max.)
(Volume)
Note:
* If you are using a two-speaker system, set the fader level to “00.
2
Adjust the level.
Note:
Normally the control dial works as the volume control. So you do not have to select “VOL” to
adjust the volume level.
1
2
Equalization pattern indicator
Equalization pattern changes as you adjust the bass or treble.
SOUND ADJUSTMENTS
Adjusting the sound
You can adjust the sound characteristics to your preference.
EN15-19KD-SX975/SX875[U]f 18/1/01, 09:0915
16
ENGLISH
BBE
Turning on/off the BBE
II
function
The BBE
II
* function restores the brilliance and clarity of the original live sound in recording,
broadcasts, etc.
When a speaker reproduces sound, it introduces frequency-dependent phase shifting, causing
high-frequency sounds to take longer to reach the ear than low frequency sounds. The BBE
II
function adjusts the phase relationship between the low, mid and high frequencies by adding
a progressively longer delay time to the low and mid frequencies, so that all frequencies
reach the listeners ears at the proper time.
In addition, the BBE
II
function boosts low and high frequencies, which loudspeakers tend to
be less efficient in reproducing, through dynamic, program-driven augmentation. When
combined with the phase compensation feature, the resulting sound has a clearer, more
finely detailed “live” presence.
Each time you press BBE, the BBE
II
function changes as follows.
As the number gets higher, the BBE
II
function becomes stronger. The initial setting is BBE 2.
* Under license from BBE Sound, Inc.
R
is a trademark of BBE Sound, Inc.
EN15-19KD-SX975/SX875[U]f 18/1/01, 09:0916
ENGLISH
17
Using the Sound Control Memory (SCM)
You can select and store a preset sound adjustment suitable to each playback source.
(Advanced SCM)
Selecting and storing the sound modes
Once you select a sound mode, it is stored in memory, and will be recalled every time you
select the same source. A sound mode can be stored for each of the following sources
FM1, FM2, FM3, AM, CD and external components.
If you do not want to store the sound mode separately for each playback source, but
want to use the same sound mode for all the sources, see Canceling Advanced SCM on
page 23.
Select the sound mode you want.
Each time you press the button, the sound mode changes as follows:
When SCM LINK is set to LINK ON, the selected sound mode can
be stored in memory for the current source and the effect applies only
to the current source. Each time you change the playback source, the
SCM indicator flashes on the display.
When SCM LINK is set to LINK OFF, the selected sound mode
effect applies to any source.
Indication For: Preset values
Bass Treble BBE
II
SCM OFF (Flat sound) 00 00 BBE 2
BEAT Rock or disco music +02 00 BBE 2
SOFT Quiet background music +01 03 Off
POP Light music +04 +01 Off
SCM
SCM
EN15-19KD-SX975/SX875[U]f 18/1/01, 09:0917
18
ENGLISH
Recalling the sound modes
1
Select the source while the SCM indicator is lit
on the display.
The SCM indicator starts flashing, and the sound mode stored
in memory for the selected source is recalled.
Notes:
You can adjust each sound mode to your preference, and store it in memory.
If you want to adjust and store your original sound mode, see “Storing your own sound adjustments”
on page 19.
To adjust the bass and treble reinforcement levels or to turn on/off the BBE
II
function temporarily,
see pages 15 and 16. (Your adjustments will be canceled if another source is selected.)
Sound mode indicator
1
EN15-19KD-SX975/SX875[U]f 18/1/01, 09:0918
ENGLISH
19
1
Call up the sound mode you want to adjust.
See page 18 for details.
2
To adjust the bass or treble level
1 Select BAS or TRE.
2 Adjust the bass or treble level.
To turn on or off the BBE
II
function
See page 16.
3
Press and hold SCM (Sound Control Memory)
until the sound mode you have selected
flashes on the display.
Your setting is stored in memory.
4
Repeat the same procedure to store other settings.
To reset to the factory settings
Repeat the same procedure and reassign the preset values listed in the table on page 17.
Storing your own sound adjustments
You can adjust the sound modes (BEAT, SOFT, POP: see page 17) to your preference and
store your own adjustments in memory.
1
2
Within
5 seconds
Within
5 seconds
Within
5 seconds
2
1,3
2
2
SCM
SCM
EN15-19KD-SX975/SX875[U]f 18/1/01, 09:0919
20
ENGLISH
OTHER MAIN FUNCTIONS
Setting the clock
1
Press and hold SEL (Select) for more than 2 seconds
so that one of the PSM items appears on the display.
2
Set the hour.
1 Select “CLOCK H (Hour)” if not
shown on the display.
2 Adjust the hour.
3
Set the minute.
1 Select “CLOCK M (Minute).”
2 Adjust the minute.
4
Finish the setting.
To check the current clock time while the unit is turned off, press DISP.
The power turns on, the clock time is shown for 5 seconds, then the power turns off.
To check the other information during play
Press DISP (Display). Each time you press the button, the other information (either the clock
or the source name) will be shown on the lower part of the display for a while.
1
1
2
2
DISP
1,4
2,3
2,3
EN20-25KD-SX975/SX875[U]f 18/1/01, 09:1420
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

JVC KD-SX875 User manual

Category
Car video systems
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI