JVC SP-UXGN9V User manual

MICRO COMPONENT SYSTEM

UX-GN7V

Consists of CA-UXGN7V and SP-UXGN9V

LVT1990-006C

[US, UB, UW, UX, UA]

INSTRUCTIONS

English

UX-GN7V[US]EN-frontcover.fm Page 1 Friday, May 8, 2009 5:34 PM

G-1

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

CAUTION

The F button in any position does not disconnect the mains line.

Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off).

The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall

remain readily operable.

• When the system is on standby, the STANDBY lamp lights red.

• When the system is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

CAUTION

• Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able

to get out.)

• Do not place any naked flame sources, such as lighted candles, on the apparatus.

• When discarding batteries, environmental problems must be considered and local rules or laws gov-

erning the disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liq-

uids, such as vases, shall be placed on the apparatus.

CAUTION

• Excessive sound pressure from earphones or headphones can cause hearing loss.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover or cabinet. There are no user serviceable parts inside the unit;

leave all servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with

optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

Warnings, cautions and others

UX-GN7V[US]EN.book Page 1 Monday, January 19, 2009 11:51 AM

G-2

CAUTION — Proper Ventilation

To avoid risk of electric shock and fire and to protect from damage, locate the apparatus as follows:

Top/Front/Back/Sides: No obstructions should be placed in the areas shown by the dimensions below.

Bottom: Place on the level surface. Maintain adequate air path for ventilation by placing on

a stand with a height of 10 cm more.

In addition, maintain the best possible air circulation.

Front view of the main unit and speakers (CA-UXGN7V and SP-UXGN9V)

Side view of the main unit (CA-UXGN7V)

CAUTION

• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

[European Union only]

UX-GN7V[US]EN.book Page 2 Monday, January 19, 2009 11:51 AM

1

Introduction

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain

the best possible performance from the unit.

Part description .............................3

Disabling the demonstration display ............... 4

Using the remote control ..............5

Inserting the batteries into the remote

control...........................................................5

Operating the system from the remote

control........................................................... 5

Operating a TV manufactured by JVC

using the remote control ............................... 5

Preparation.....................................6

Connecting the antennas ................................6

Connecting the speakers ................................7

Connecting a TV .............................................8

Connecting a portable digital audio player......8

Connecting an external digital audio device ...9

Connecting a subwoofer .................................9

Connecting the power cable ...........................9

Selecting the video signal type ..................... 10

Basic operations..........................11

Using the number buttons............................. 11

Turning on/off the main unit ..........................11

Adjusting the volume.....................................11

Turning off the sound temporarily ................. 11

Selecting the sound mode ............................ 11

Customizing the equalization pattern............ 12

Emphasizing both treble and bass................ 12

Emphasizing the bass...................................12

Sharpening the voice sound .........................13

Selecting the headphone surround mode ..... 13

Setting the clock............................................13

Changing the brightness of the display

window........................................................ 14

Turning off the display window...................... 14

Auto standby function ...................................14

Locking disc ejection..................................... 14

Listening to radio broadcasts ....15

Setting the AM tuner spacing........................15

Selecting a radio station................................16

Tuning in to a preset radio station................. 16

Playing back sources from

external devices...........................17

Playing back sources from external

devices........................................................17

Selecting the signal gain ...............................17

Basic operations of disc/file

playback .......................................18

Playing back a disc .......................................18

Playing back a file .........................................19

Selecting the file type....................................20

Checking the current status in the display

window........................................................21

Stopping playback.........................................22

Resuming playback.......................................22

Pausing playback..........................................22

Fast reverse/fast forward search ..................22

Playing back from a position 10 seconds

before..........................................................23

Slow motion playback ...................................23

Skipping to the beginning of a title/group......23

Skipping to the beginning of a chapter/

track/file ......................................................23

Selecting a chapter/track using the number

buttons ........................................................23

Skipping forward/backward at 30 second or

5 minute intervals........................................23

Selecting a chapter/track from the menu

screen .........................................................24

Introduction

Preparation

Basic operations

Listening to radio broadcasts

Playing back sources from

external devices

Basic operations of disc/file

playback

Table of contents

UX-GN7V[US]EN.book Page 1 Monday, January 19, 2009 11:51 AM

Introduction

2

Convenient functions of disc/file

playback .......................................25

Playing back a disc/file in the desired order

(Program playback) ....................................25

Playing back a disc/file in a random order

(Random playback) .................................... 26

Playing back a disc/file repeatedly

(Repeat playback) ...................................... 27

Playing back a specified part repeatedly

(A-B repeat playback)................................. 27

Selecting the audio language, subtitle

language and view angle ............................ 28

Magnifying the picture................................... 28

Adjusting the picture quality (VFP)................29

Creating realistic sound (3D PHONIC) ......... 30

Selecting the audio volume level of

the DVD ......................................................30

Using the status bar and the

menu bar.......................................31

Designating the time (Time search) .............. 32

Changing the initial settings with

the preference screen .................33

Basic operations ...........................................33

LANGUAGE.................................................. 33

PICTURE ......................................................34

AUDIO........................................................... 35

OTHERS.......................................................35

Language codes ..........................36

Recording sound directly from

a CD to a USB device ..................37

Recording all tracks from a CD to a USB

device ......................................................... 37

Deleting a track/group from a USB device....39

Adding (Editing) a title to a track/group on

a USB device.............................................. 39

Enjoying karaoke .........................41

Singing a song in karaoke.............................41

Reducing the volume of the original vocals

(Vocal masking)..........................................43

Adjusting the sound key to match your

voice range .................................................43

Adjusting the echo effect...............................43

Programming karaoke songs (Karaoke

program playback)......................................44

Timer .............................................45

Using the sleep timer ....................................45

Using the playback timer...............................46

Notes on operation ......................47

Suitable locations for the main unit ...............47

Condensation................................................47

Cleaning the main unit ..................................47

Notes on handling .........................................47

License and trademark .................................48

Notes on discs/files .....................49

Playable disc/file types..................................49

Data hierarchy...............................................52

Handling discs...............................................52

Troubleshooting...........................53

Specifications ..............................56

Main unit (CA-UXGN7V) ...............................56

Speaker (SP-UXGN9V) ................................56

Supplied accessories ....................................56

Convenient functions of

disc/file playback

Recording sound directly

from a CD to a USB device

Enjoying karaoke

Timer

Reference

How to read this manual

• This manual explains the operations assum-

ing that you will use the remote control.

Some buttons on the main unit are the same

as those on the remote control. You can use

either button in this case.

• Some diagrams in this manual are simplified

or exaggerated for the purpose of explana-

tion.

• You can operate some functions differently

from the explanation given in this manual.

• Depending on the disc/file, you may not

obtain the explained result even after follow-

ing the operation in this manual.

• The following marks refer to the usable

discs/files for the explained function.

UX-GN7V[US]EN.book Page 2 Monday, January 19, 2009 11:51 AM

3

Introduction

The numbers refer to the pages in which the parts are explained.

■ Activating the buttons on the main unit

Before using the buttons on the main unit, place

your hand over the front of the main unit. The but-

tons, controls and indicators gradually start illumi-

nating.

■ Using the ¢/4 and [VOL +/–] controls

To operate the ¢/4 control on the right front

of the main unit, vertically slide your finger on the

area between ¢ and 4.

Similarly, to operate the [VOL +/–] control, slide your

finger on the

area

between [VOL +] and [VOL –].

■ Opening the front cover

To use the buttons and terminals concealed under

the front cover, use your finger to pull open the part

indicated with [ 2 PULL OPEN].

Front view

Remote control sensor

Refer to “Display window” shown on page 4.

Rear view

Part description

UX-GN7V[US]EN-02.fm Page 3 Thursday, February 5, 2009 10:54 AM

Introduction

4

1

The “USB” indicator lights up when a USB

device is selected as the source.

2

Disc format indicators

• The “SVCD” indicator lights up when playing

back an SVCD.

• The “VCD” indicator lights up when playing

back a VCD.

• The “CD” indicator lights up when playing back

a CD.

• The “DVD” indicator lights up when playing

back a DVD.

3 The “3DPHONIC” indicator lights up when the

3D PHONIC function is activated.

4 The “HP SUR” indicator lights up when the

headphone surround function is activated.

5 The “SOUND” indicator lights up when the

sound mode function is activated.

6 The “S.TURBO” indicator lights up when the

Sound Turbo II function is activated.

7 The “HBS” indicator lights up when the HBS

function is activated.

8 The “PRGR.” indicator lights up when the pro-

gressive video signal type is selected.

9 The “RESUME” indicator lights up when the

position where playback has been stopped is

stored.

0 Radio indicators

• The “AM” indicator lights up when an AM

broadcast is received.

• The “FM” indicator lights up when an FM

broadcast is received.

• The indicator lights up when an FM stereo

broadcast is received with sufficient signal

intensity.

• The indicator lights up when an FM broad-

cast is received in monaural.

A

The indicator lights up when the my sound

function is activated.

B

Timer indicators

• The indicator lights up when the playback

timer is ready or being set, and flashes when

the playback timer is working.

• The “1”, “2” or “3” indicator lights up when the

playback timer is ready or working, and

flashes when the playback timer is being set.

• The “SLEEP” indicator lights up when the

sleep timer is activated.

C The “REC” indicator lights up when recording

starts.

D The “MIC” indicator lights up when the micro-

phone mixing function is activated.

E The “V.MASK” indicator lights up when the

vocal masking function is activated.

F The “C.VOICE” indicator lights up when the

clear voice function is activated.

G The “PG” or “PL” indicator lights up when an

original program or play list is selected.

H The “PRGM” indicator lights up when the pro-

gram playback function is activated.

I The “RND” indicator lights up when the random

playback function is activated.

J The “ ”, “

1” or “ ALL” indicator lights up

when the repeat playback function is activated.

K The “A.STBY” indicator lights up when the auto

standby function is ready, and flashes when the

auto standby function is working.

When you connect the power cable into the AC outlet, the dem-

onstration display automatically starts in the display window.

Before using this system, turn off the demonstration display.

■ When the main unit is turned off

Hold down [DEMO] on the main unit

until “DEMO CLR” appears.

Display window

Disabling the demonstration display

Main unit (front view)

UX-GN7V[US]EN-02.fm Page 4 Friday, May 8, 2009 5:37 PM

5

Introduction

The numbers refer to the pages in which the parts

are explained.

Insert the batteries into the remote control by

matching the polarity (+ and −) correctly.

• If the range or effectiveness of the remote con-

trol decreases, replace both batteries.

Point the remote control directly at the

front of the main unit.

• Do not block the remote control sensor on the

main unit.

You can use the remote control of this system to

operate a TV manufactured by JVC.

* Make sure to hold down [SHIFT] when you press

the desired function button.

Inserting the batteries into

the remote control

Operating the system from

the remote control

Operating a TV

manufactured by JVC using

the remote control

Remote control

button

Usage

[AUDIO/TV

F

]

+ [SHIFT]*

Turns on/off the TV.

[TV/VIDEO] Changes between the

TV and video input.

[

– TV CH]/[TV CH+]

+ [SHIFT]*

Changes channels.

[VOLUME ]/

[VOLUME ]

+ [SHIFT]*

Adjusts volume.

R03 (UM-4)/AAA

(24F) type dry-cell

batteries (supplied)

Using the remote control

UX-GN7V[US]EN.book Page 5 Monday, January 19, 2009 11:51 AM

Preparation

6

Setting up the AM loop antenna

NOTE

• Keep the AM loop antenna cable wrapped

around the AM loop antenna frame, otherwise

the effectiveness and sensitivity of the AM loop

antenna may be reduced.

Connecting the AM loop antenna

Turn the AM loop antenna to find the best position

for radio reception.

NOTE

• Make sure that the antenna conductors do not

touch any other terminals. This could cause poor

reception.

When radio reception with the supplied FM

antenna is poor, or when using a communal

antenna

• When using an antenna other than those sup-

plied with this system, refer to the operation

manuals for the antenna and converter for

details of connection.

• When positioning the antennas, find the best

position for reception while listening to an actual

radio program (refer to “Listening to radio broad-

casts” on page 15).

• You cannot receive a radio broadcast without the

antenna connection.

Connecting the antennas

AM loop antenna (supplied)

If insulation covers the tips of the

antenna cable, twist and pull off

the insulation.

Main unit (rear view)

FM antenna (supplied)

Main unit (rear view)

FM antenna

Stretch out the FM

antenna to the best

position for radio

reception.

Main unit (rear view)

Antenna cable

(not supplied)

Outdoor FM

antenna

(not supplied)

Converter (not sup-

plied: compatible

with 300

C

/75

C

)

Coaxial cable

(not supplied)

Depending on the radio reception

conditions, an FM feeder antenna

(not supplied: compatible with

300 C) can be used. In this case,

a converter (not supplied) is

required.

or

Communal

antenna terminal

Preparation

Do not connect the power cable until all other connections have been made.

UX-GN7V[US]EN.book Page 6 Monday, January 19, 2009 11:51 AM

7

Preparation

Connect the speakers to the main unit by connecting the colored cables to the same color terminals on the

rear of the main unit.

■ IMPORTANT

• Improper speaker cable connection reduces the

stereo effect and sound quality.

• The supplied speakers are magnetically

shielded, but color irregularity may occur on the

TV depending on some conditions. To prevent

color irregularity, set up the speakers following

the instructions below.

1. Turn off the main power of the TV before

setting up the speakers.

2. Place the speakers enough distance from the

TV so that they do not cause color irregularity

on the TV.

3. Wait for approximately 30 minutes before

turning on the main power of the TV again.

CAUTION

• The supplied speakers are manufactured exclu-

sively for use with the supplied main unit as

parts of this system. Do not connect the supplied

speakers to devices other than the supplied

main unit. Doing so may damage the speakers.

• Do not connect external speakers together with

the supplied speakers. The change in imped-

ance may damage the main unit and the speak-

ers.

Connecting the speakers

Right speaker

(rear view)

Left speaker

(rear view)

Speaker cable

If insulation covers the tips of

the speaker cables, twist and

pull off the insulation before

connecting the speaker cables.

Main unit

(rear view)

Red

Black

Preparation (continued) Do not connect the power cable until all other connections have been made.

UX-GN7V[US]EN-03.fm Page 7 Thursday, February 5, 2009 9:53 AM

Preparation

8

After connecting a TV, follow the instructions on

page 10.

■ IMPORTANT

• Connect the main unit directly to a TV (or a mon-

itor) without routing through a video cassette

recorder (VCR). Otherwise picture distortion

may occur during playback. (Routing the con-

nection through a VCR, however, does not affect

the audio quality.)

• Connecting the main unit to a VCR-built-in-TV

may also cause picture distortion during play-

back.

You can listen to analog sound from a connected

portable digital audio player.

Connecting a TV

Connecting a TV with the

[COMPONENT] terminals

Main unit

(rear view)

TV

To component

input terminals

Component video cable (not supplied)

Connecting a TV with the [VIDEO]

terminal

TV

Composite video cable (supplied)

Main unit

(rear view)

To a video input terminal

Connecting a portable digital

audio player

Main unit

Direct connection

TV (or monitor)

VCR

To an audio output terminal

(such as a headphone ter-

minal)

Main unit (front view)

Input

Output

Stereo mini plug cable

(not supplied)

Portable digital audio player

or other audio device

UX-GN7V[US]EN.book Page 8 Monday, January 19, 2009 11:51 AM

9

Preparation

NOTE

• Before connecting or disconnecting an external

device, press [VOLUME ] repeatedly to set the

volume of this system to the minimum. You can

also use the [VOL –] control on the main unit.

• Select the appropriate setting for “DIGITAL

AUDIO OUTPUT” according to the connected

device. Refer to page 35.

• You can output the audio signal from the

[OPTICAL DIGITAL OUTPUT] terminal when

“DVD/CD” is selected as the source in the dis-

play window.

When you connect this system with an amplifier-

built-in subwoofer (not supplied), you can enjoy a

more dynamic bass sound. Refer to the manual of

the subwoofer for details.

• Connect the power cable after you complete the

other connections.

• The [STANDBY] lamp on the main unit lights up.

Connecting an external

digital audio device

Main unit

(rear view)

Output

Optical digital cable

(not supplied)

To an optical digital

input terminal

Input

AV amplifier with

a built-in decoder

Connecting a subwoofer

Connecting the power cable

Audio cable (not supplied)

(Use the audio cable supplied with

the amplifier-built-in subwoofer or

a commercially available cable.)

Amplifier-built-in subwoofer

(not supplied)

Main unit

(rear view)

AC outlet

Main unit

(rear view)

Preparation (continued) Do not connect the power cable until all other connections have been made.

UX-GN7V[US]EN.book Page 9 Monday, January 19, 2009 11:51 AM

Preparation

10

To view an image on the TV screen, select the

video signal type correctly according to the TV

after connecting the main unit to the TV.

1 Turn on the main unit.

• Refer to “Turning on/off the main unit” on

page 11.

2 Press [SCAN MODE] repeatedly to

select the video signal type suit-

able for the TV.

• Select “PAL” for a TV only compatible with a

PAL interlaced video signal.

• Select “PAL PRG” for a TV equipped with a

component terminal and compatible with a

PAL progressive video signal.

• Select “NTSC” for a TV only compatible with

an NTSC interlaced video signal.

• Select “NTSC PRG” for a TV equipped with

a component terminal and compatible with

an NTSC progressive video signal.

NOTE

• When “PAL PRG” or “NTSC PRG” is selected,

the “PRGR.” indicator lights up in the display

window.

3 Press [ENTER/SET].

Selecting the video signal

type

UX-GN7V[US]EN.book Page 10 Monday, January 19, 2009 11:51 AM

11

Basic operations

Examples:

5: [5]

15: [ 10] →

[1]

→

[5]

150: [ 10] → [ 10] → [1] → [5] → [0]

Press [AUDIO/TV

F

] (or

F

on the

main unit).

• The power of the main unit turns on and the

[STANDBY] lamp on the main unit turns off.

• Press [AUDIO/TV

F

] (or

F

on the main unit)

again to turn off the power of the main unit. (The

main unit enters the standby mode.)

• With the power off, pressing [DVD/CD 6],

[USB 6], [TUNER], [AUDIO IN] or 0 also

turns on the main unit.

The function assigned to the pressed button

starts working at the same time.

Press [VOLUME ] or [VOLUME ]

repeatedly.

• You can also adjust the volume by using the

[VOL +/–] control on the main unit.

Press [FADE MUTING].

• Press [FADE MUTING] again to restore the

sound.

A combination of JVC sound technologies enables

you to select the desired sound pattern. This func-

tion is called “sound mode”.

Press [SOUND MODE] repeatedly.

• Each time you press [SOUND MODE], the dis-

play changes as follows.

- “ROCK”: For acoustic sound.

- “POP”: For vocal oriented music.

- “CLASSIC”: For classic music.

- “JAZZ”: For jazz music. *

- “REGGAE”: For slow rhythm. *

- “SALSA”: For salsa music. *

- “SAMBA”: For samba music. *

- “FLAT”: Cancels the sound mode.

* Selecting these items provides a surround effect.

Using the number buttons

Number

buttons

Turning on/off the main unit

Adjusting the volume

Turning off the sound

temporarily

Selecting the sound mode

Basic operations

UX-GN7V[US]EN.book Page 11 Monday, January 19, 2009 11:51 AM

Basic operations

12

Audible sound frequencies vary according to the

individual. This function creates the appropriate

equalization pattern according to your hearing

preferences. This function is called “My Sound”.

■ When a disc/file is stopped

1 Hold down [MY SOUND].

TV screen

2 Press [ENTER/SET].

• 5 test tones are emitted individually from the

speakers.

TV screen

3 As soon as you hear the test tone,

press [ENTER/SET].

• The measurements are stored.

• An appropriate equalization pattern is cre-

ated and shown on the TV screen.

4 Press  or  repeatedly to select

the preset number from 1 to 3.

• The equalization pattern is stored. The preset

number, which is assigned to the equalization

pattern, turns green on the TV screen.

TV screen

• To measure again, press  or  repeatedly

to select “EXIT” on the TV screen, and then

press [ENTER/SET]. You can store up to 3

equalization patterns.

5 Press [ENTER/SET].

NOTE

• You can cancel the setting by pressing [MY

SOUND].

Press [MY SOUND].

• Each time you press [MY SOUND], the preset

equalization pattern changes.

• To deactivate the stored equalization pattern,

select “OFF”.

NOTE

• This function does not work for some files.

You can boost both high and low frequencies of

the sound. This function is called “Sound Turbo II”.

Press [S.TURBO II].

• Each time you press [S.TURBO II], the setting

turns on and off.

NOTE

• While the Sound Turbo II function is activated,

the HBS function is automatically activated.

When the Sound Turbo II function is deactivated,

you can boost only the low frequency. This function

is called “HBS (hyper bass sound)”.

Press [HBS] while holding down

[SHIFT].

• Each time you press [HBS], the setting turns on

and off.

NOTE

• Activating the Sound Turbo II function activates

the HBS function. At this time, however, the

“HBS” indicator does not light up.

Customizing the equalization

pattern

Signal level

Emphasizing both treble and

bass

Emphasizing the bass

Selecting the preset equalization

pattern

UX-GN7V[US]EN.book Page 12 Monday, January 19, 2009 11:51 AM

13

Basic operations

This function allows you to easily understand dia-

log recorded on the disc/file even with the volume

down low. This function is useful when you are

watching a movie.

Press [C.VOICE] while holding down

[SHIFT].

• Each time you press [C.VOICE], the setting

turns on and off.

NOTE

• “C.VOICE” refers to “clear voice”.

You can listen to surround sound via headphones

connected to the [PHONES] terminal.

■ When headphones are connected to the

[PHONES] terminal

Press [3D P/HPS] while holding down

[SHIFT].

• Each time you press [3D P/HPS], the setting

turns on and off.

NOTE

• The [PHONES] terminal is for connecting a pair

of headphones equipped with a stereo mini plug

(not supplied). When headphones are con-

nected, no sound is output from the speakers.

• This function does not work for a JPEG, ASF,

DivX, MPEG1 or MPEG2 file.

• “HPS” refers to “headphone surround”.

You can set the clock when the main unit is on or

off.

1 Press [CLOCK/TIMER] repeatedly

to select the clock in the display

window.

2 Press  or  to select the hour.

3 Press [ENTER/SET].

4 Press  or  to select the minute.

5 Press [ENTER/SET].

• The clock starts from 0 seconds in the

minute you set.

NOTE

• While setting the clock, you can return to the

previous step by pressing [CANCEL] or you can

stop the setting by pressing [CLOCK/TIMER].

• To adjust the clock, press [CLOCK/TIMER]

repeatedly until the clock appears in the display

window, and then press [ENTER/SET]. The fol-

lowing procedure is the same as steps 2 to 5.

• Press [DISPLAY/CHARA] to display the clock

when using this system. (Refer to page 21.)

• The clock gains or loses approximately 1 minute

per month.

• If the power cable of the main unit is discon-

nected from the AC outlet or the power is inter-

rupted, the clock setting is lost. Set the clock

again.

Sharpening the voice sound

Selecting the headphone

surround mode

Setting the clock

Basic operations (continued)

UX-GN7V[US]EN-04.fm Page 13 Wednesday, April 8, 2009 10:26 AM

Basic operations

14

■ When the main unit is turned on

Press [ECO/DIMMER] repeatedly.

• Each time you press [ECO/DIMMER], the setting

changes to “DIM ON”, “AUTO DIM” or “DIM

OFF” in the display window.

• When “AUTO DIM” is selected and no operation

is performed for approximately 5 minutes, the

display window automatically becomes darker

than the normal display window.

You can reduce the power consumption by turning

off the display window when the main unit is off.

■ When the main unit is turned off

Press [ECO/DIMMER] repeatedly.

• Each time you press [ECO/DIMMER], the dis-

play changes as follows.

- Selecting the normal display turns on the clock

display and activates the buttons on the main

unit.

- Selecting “DISP OFF” turns off the clock dis-

play and activates the buttons on the main

unit.

- Selecting “ECO ON” turns off the clock display

and deactivates the buttons on the main unit.

NOTE

• You can use the remote control in any of the

above cases.

• “ECO” refers to “ecology”.

If no sound is produced for 3 minutes, the main

unit automatically turns off.

This function is available when a loaded disc or a

connected USB device is selected as the source.

■ When a loaded disc or a connected USB

device is selected as the source

Press [AUTO STBY].

• The “A.STBY” lights up in the display window.

• Each time you press [AUTO STBY], the setting

turns on and off.

When playback of a loaded disc or a connected

USB device finishes, the auto standby function

starts a countdown. At this time, the “A.STBY” indi-

cator starts flashing.

When no operation is performed for 3 minutes, the

main unit automatically turns off.

NOTE

• When you change the source to a radio broad-

cast or device connected to the [AUDIO IN] ter-

minal, this function temporarily deactivates.

You can lock the disc tray to prevent the disc from

being ejected.

■ When the main unit is turned off

Press 0 on the main unit while hold-

ing down 7 on the main unit.

• “LOCKED” appears in the display window.

• To cancel the disc ejection lock, press 0 on the

main unit while holding down 7 on the main unit

again. “UNLOCKED” appears in the display win-

dow.

Changing the brightness of

the display window

Turning off the display

window

Auto standby function

Locking disc ejection

Activating the auto standby function

Performance of the auto standby

function

Setting the disc ejection lock

Main unit (front view)

For the locations of the remote

control buttons, refer to page 11.

UX-GN7V[US]EN-04.fm Page 14 Friday, February 13, 2009 9:54 AM

15

Listening to radio broadcasts

*

For the number button usage, refer to “Using the

number buttons” on page 11.

AM stations are spaced 9 kHz apart in some coun-

tries and 10 kHz in other countries.

1

Press [TUNER] repeatedly to select

“TUNER AM” in the display win-

dow.

2 Press [AUDIO/TV F] (or F on

the main unit) to turn off the

power.

3 Hold down [CD 3 USB REC] on

the main unit.

• Each time you hold down [CD 3 USB REC],

the setting toggles between “9K STEP” and

“10K STEP” in the display window.

NOTE

• When “ECO ON” is selected, you cannot operate

this function. (Refer to page 14.)

Number

buttons

*

Setting the AM tuner spacing

Main unit (front view)

Listening to radio broadcasts

UX-GN7V[US]EN-05.fm Page 15 Tuesday, February 10, 2009 6:03 PM

Listening to radio broadcasts

16

1 Press [TUNER] to select “TUNER

FM” or “TUNER AM” in the display

window.

• Pressing [TUNER] selects a radio broadcast

as the sound source.

2 Hold down 4 or ¢.

• The radio frequency starts changing in the

display window.

• When the main unit has received a broad-

cast, the frequency automatically stops

changing.

• You can select a specific radio station while

searching for a broadcast. Press 4 or

¢ to stop the search when the desired

frequency appears in the display window.

NOTE

• If an FM stereo broadcast is difficult to hear

because of noise, you may be able to hear the

broadcast more easily by pressing [TUNER/

PLAY MODE] to switch the sound to monaural

reception. In this case, the (monaural) indica-

tor lights up in the display window. To return the

sound to stereo reception, press [TUNER/PLAY

MODE] again. The (stereo) indicator lights up

in the display window.

Presetting radio stations in the main unit allows

you to easily tune in to a radio station. You can

store up to 30 FM radio stations and up to 15 AM

radio station.

1 Select a radio station you want to

store.

• Refer to “Selecting a radio station” shown on

the left.

• You can also preset selected stereo or mon-

aural reception for an FM broadcast.

2 Press [ENTER/SET].

• “SET” flashes in the display window for a

few seconds.

3 While “SET” is flashing, press the

number buttons to select the pre-

set number you want to assign.

4 Press [ENTER/SET].

• “STORED” appears and the selected radio

station is stored.

NOTE

• When you store a radio station to a preset num-

ber to which another radio station has previously

been stored, the newly set radio station replaces

the previously stored radio station.

• When the power cable of the main unit is discon-

nected from the AC outlet or the power is inter-

rupted, the preset radio station settings may be

lost within a few days. If the setting is lost, set

the preset radio station again.

■ When an FM or AM radio broadcast is

selected as the source

Press the number buttons to select

the preset number of the radio station

to which you want to tune in.

Selecting a radio station Tuning in to a preset radio

station

Presetting radio stations

Tuning in to a preset radio station

UX-GN7V[US]EN-05.fm Page 16 Thursday, February 5, 2009 10:05 AM

17

Playing back sources from external devices

1 Press [AUDIO IN].

• “AUDIO IN” is selected as the source in the

display window.

2 Start playback on the connected

device.

3 Adjust the volume or the sound

settings for your preference.

• Refer to page 11.

NOTE

• Before connecting or disconnecting an external

device, press [VOLUME ] repeatedly to set the

volume of this system to the minimum. You can

also use the [VOL –] control on the main unit.

You can select the gain of the signal from the

[AUDIO IN] terminal.

Press [DVD/AUDIO IN LEVEL] while

holding down [SHIFT].

• Each time you press [DVD/AUDIO IN LEVEL],

the signal gain setting toggles between “NOR-

MAL” and “HIGH” in the display window.

• Select “NORMAL” for normal operation.

Playing back sources from

external devices

Selecting the signal gain

Playing back sources from external devices

UX-GN7V[US]EN.book Page 17 Monday, January 19, 2009 11:51 AM

Page is loading ...

JVC SP-UXGN9V User manual

This manual is also suitable for

JVC SP-UXGN9V User manual

Related papers

Other documents