Alula Z-Wave RE934Z Installation guide

Brand
Alula
Model
Z-Wave RE934Z
Type
Installation guide

This manual is also suitable for

Verify proper installation and operation using the panel’s installation manual.
Installation
1. Power down the Connect+.
2. Open the cover.
3. Unplug the battery cord.
4. Unplug the power cord.
5. Insert the RE934Z into expansion slot 3 of the Connect+, gently inserting the connector and
snapping the stand-offs into place.
6. Connect battery cord, plug the power, and close the cover to the Connect+.
RE934Z Z-Wave Expansion Card adds home automation capability to the
system. The system will be able to start or join an existing Z-Wave network,
and control Z-Wave capable 3rd party devices.
Features
• Expansion Card that plugs into the Connect+ / BAT-Connect
• Provides communications with Z-Wave devices enabling a broad
range of home automation features
Installation
1. Power down the system.
2. Insert the Z-Wave Expansion Card.
3. Power up the system.
RE934Z Z-Wave
™
Expansion Card
Connect+
™
Encrypted
I
N
S
T
A
L
L
G
U
I
D
E
I
LED Indication
Power
(Green)
ON - When system is AC powered
OFF - When system does not have AC power
Z-Wave
(Red)
(Normally) OFF - ashes with each Z-Wave message received from system
Connect+: Insert the RE934Z into expansion slot 3 of the Connect+, gently inserting the
connector and snapping the stand-offs into place.
BAT-Connect: Insert the RE934Z into expansion Module Slot of the BAT-Connect, gently
inserting the connector and snapping the stand-offs into place.
SLOT 1 SLOT 2
SLOT 3
BACKUP
BATTERY
Connect Family
BAT-Connect
Connect+
Specications subject to change without notice
Physical
Dimensions
Weight
Current Draw
1.8 x 1.7 x 0.1 inches (4.6 x 4.3 x 0.3 centimeters)
1.1 ounces (31.2 grams)
30-35mA (Nominal)
Environmental
Operating Temperature
Maximum Humidity
0°F to 120°F (-17.8°C to 48.8°C)
85% non-condensing relative humidity
Certication
RE934Z FCC, IC
Specications
47-0057-01 • REV B • 2019-10-01
Tech Support Line • (888) 88-ALULA • (888) 882-5852
alula.net
02
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux cnr d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
IC: 8310A-RE934Z
IC Model: RE934Z
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be
received, including interference that may cause undesired
operation.
Changes or modications not expressly approved by Alula could
void the user’s authority to operate this equipment.
FCC ID: U5X-RE934Z
TRADEMARKS
Alula and Connect+ are trademarks owned by Alula Holdings, LLC.
Z-Wave and Z-Wave Plus are registered trademarks of Silicon Labs.
  • Page 1 1
  • Page 2 2

Alula Z-Wave RE934Z Installation guide

Brand
Alula
Model
Z-Wave RE934Z
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents