3/'08
23(5$7,210$18$/
AM/FM-MPX DVD/VCD/SVCD/CD/MP3/MP4 Player
Receiver w/USB Interface & SD/MMC Card Reader
ZZZS\OHDXGLRFRP
&217(176
Contents ------------------------------------------------------ 1
Welcome ----------------------------------------------------- 2
Note on Installation ---------------------------------------- 2
Precautions -------------------------------------------------- 2
Installation --------------------------------------------------- 3 – 4
Wiring Diagram --------------------------------------------- 5
Main Unit – Controls Location -------------------------- 6
Main Unit – General Operation ------------------------- 7 – 8
Main Unit – Radio Operation ---------------------------- 9
Main Unit – Disc/USB/SD/MMC Operation----------- 10 – 11
Remote Handset – Control Location------------------- 12
Remote Handset – General Operation --------------- 13 – 14
Remote Handset – Radio Operation ------------------ 15
Remote Handset – Disc/USB/SD/MMC Operation- 16 – 17
Specification ------------------------------------------------- 18
Simple Trouble Shooting Guide ------------------------ 19
1
:(/&20(
Thank you for purchasing our company multi-media player! To operate the unit correctly,
please read the operation manual carefully before using. Keep this operation manual for
future reference.
127(21,167$//$7,21
The unit is designed for 12V DC negative ground operation system only. Before installing
the unit, make sure your vehicle is connected to DC 12V negative ground electrical system.
The negative battery terminal must be disconnected before making connections. By doing
so, it can reduce the chance of damaging the unit to short circuit.
Be sure to connect the colour coded leads correctly accordingly to the wiring diagram.
Incorrect connections may cause the unit malfunction or damage the vehicle’s electrical
system.
Be sure to connect the speaker(-) leads to the speaker(-) terminal. Never connect the left
and right channel speaker wires together or to the vehicle body.
Do not block vents or radiator panels of the unit. Blocking them will cause heat to build up
inside the unit and may cause damage or fire.
After the completion of installation (or after replacing the battery of vehicle), make sure to
press the RESET button on the main unit with pointed object (such as ball-point pen) to set
the unit to its initial status.
35(&$87,216
- This unit can play the following discs (12 cm) and media files: DVD+R/RW / DVD-
R/RW / MP4 / DivX / AVI / SVCD / VCD / MP3 / WMA / CD-R/RW / JPEG
- Do not attempt to modify the unit, modifying the unit may cause the malfunction and
damage of the unit.
- Stop the vehicle before carrying out any operation that could interfere with your driving.
- Do not work in extreme high or low temperature. The normal temperature for operation
is between -20 and +60 degree Celsius.
- To enjoy optimum sound and images while playing, handle the discs as follows:
. to hold the discs by the edge so the surface will not be damaged with finger prints
. do not attach label or sticker to the discs surface
. do not put paste residue or ink on the surface of discs
. wipe the discs with a dry soft cloth from the center gold toward the outer edge
. do not bend the discs
. do not store the discs in the following places: areas exposed to direct sunlight, humid
or dusty.
2
,167$//$7,21
3
,167$//$7,21
Mounting Method B
This mounting method is used
for most Japanese cars. The
actual mounting method
should depend on the type of
cars and the supplied parts.
Note:
- Store small articles in
places not accessible to
children
- Install only with the
supplied screws
- Installation varies on
type of cars and supplied
parts. You should have
the unit installed by
qualified technician
To Detach the Front Panel
Before detaching the front
panel, be sure to turn off the
unit. Press the release button
and the front panel will fold
down to the level, slide the
front panel to the right and
pull it off forward you.
To Replace the Front Panel
First, insert the right hand side
of the front panel into the
main unit. Then push the left
hand side of the front panel
into the main unit until it locks
firmly.
Precautions
Do not touch the connectors
on the front panel and main
unit, it will result in poor
electrical contact. Only wipe
the connectors with a clean
and dry cloth. Put the front
panel into the carry case after
it detached from the main unit.
4
:,5,1*',$*5$0
5
/2&$7,212)0$,181,7&21752/6
7 2 11 6 14 5 4 3
12 10 13 9 8 18 19 20 21 22 23 15 24
16 1 17
25
1. Unit Reset 14. Preset Station Button (1-6)
2.
Power On/Off Control (
)
15. Auto Memory Store/Scan (APS)
3.
Panel Open Button (
)
16. Disc Slot
4. Remote Control Sensor (IR) 17. Disc Eject ( )
5. LCD Display 18. Pause Control (Źűű)
6. Mode Selector (MOD) 19. Intro Play Control (INT)
7. Clock Display & Adjustment (CLK) 20. Repeat Play Control (RPT)
8. Volume Control & Function Selector 21. Random Play Control (RDM)
9. Mono/Stereo Selector (MO/ST) 22. Video System Selector (5)
10. Mute Control (MUT) 23. Audio Channels Selector (6)
11. Band Selector (BAND) 24. USB Slot
12. Auxiliary Input Jack (AUX IN) 25. SD/MMC Card Port
13. Tuning / Tracks Control (
ŹŹű
/
ŲŻŻ
)
Note
Printings & symbols on the above drawing may be varied from the exact main unit. Referred
to the main unit for exact functions & features that applied.
6
0$,181,7²*(1(5$/23(5$7,21
RESET OF THE UNIT
Operating the unit for the first time or after replacing the car battery, it is necessary to reset
the unit. Press RESET (1) on the main unit with a pointed object (such as a ball point pen)
to reset the unit to initial setting by the factory (default stage). When there are errors occur
or malfunction appears on the unit, press RESET (1) can also resume the unit to default
stage. It will also erase all the setting and memorized functions of the unit.
POWER ON/OFF CONTROL
Press (2) to turn on the unit, press it again to turn off the unit. All the memorized setting
will retain after the unit turned off.
MODE SELECTOR
Continuously pressing MOD (6) to choose your desired modes among radio, disc, USB
input, SD/MMC card input and auxiliary input operation.
VOLUME & AUDIO CONTROL
Rotate VOLUME CONTROL (8) clockwise to increase the sound level, rotate it anti-
clockwise to decrease the sound level. Continuously pressing FUNCTION SELECTOR (8)
to activate the following audio control modes: BASS (BAS) Æ TREBLE (TRE) Æ
BALANCE (BAL) Æ FADER (FAD) Æ VOLUME (VOL) Æ, by rotating FUNCTION
SELECTOR (8) clockwise or anti-clockwise to have your desired setting.
Note
When preset equalizer control is in activated, bass and treble will resume to its default stage.
PRESET EQUALIZER CONTROL
Press and hold FUNCTION SELECTOR (8) for two seconds to activate the preset equalizer,
rotate FUNCTION SELECTOR (8) clockwise or anti-clockwise to select your desired audio
equalization in the following orders: ļ DSP OFF ļ CLASSIC ļ POP ļ ROCK ļ
Note
When preset equalizer control is activated, bass and treble will resume to its default stage.
MUTE CONTROL
Press MUTE (10) to cut down the sound output, press it again to release the mode and
recover to the previous volume level.
USB SLOT
Insert USB device to the USB SLOT (24) to have playback of multi-media files that recorded.
SD/MMC CARD PORT
Insert SD/MMC card to the SD/MMC CARD PORT (25) to have playback of multi-media
files that recorded.
7
0$,181,7²*(1(5$/23(5$7,21
AUXILIARY INPUT JACK
Insert an external device to this AUX IN (12) jack in order to have output of that external
device through the unit.
CLOCK DISPLAY & ADJUSTMENT
During unit operation, press CLK (7) to recall the time display on LCD DISPLAY (5). Press
it again or after 5 seconds, the LCD DISPLAY (5) will return to its original status.
Time Setting
At clock display mode, press and hold CLK (7) until the hour digit starts blinking. Rotary
FUNCTION SELECTOR (8) clockwise or anti-clockwise to adjust the hour and confirm the
setting by pressing CLK (7), it will then change to minute setting. Rotary FUNCTION
SELECTOR (8) clockwise or anti-clockwise to adjust minute setting and confirm the setting
by pressing CLK (7).
LCD DISPLAY
The LCD DISPLAY (5) shows the status of operation on the unit.
REMOTE CONTROL SENSOR
Using the remote control handset to operate different functions of the unit by pointing the
remote control handset to the remote control sensor IR (4) and press the control key on the
remote control handset for operation.
RELEASE OF FRONT PANEL
Press (3) to fold down the front panel to the level. After the folded down of front panel,
you can detach the removable front panel from the main unit for anti-theft security purpose.
8
0$,181,7²5$',223(5$7,21
RADIO BAND SELECTOR
At radio mode, repeatedly pressing BAND SELECTOR (11) to select the desired radio band
in the following orders: Æ FM1 Æ FM2 Æ FM3 Æ AM1(MW1) Æ AM2(MW2) Æ
MANUAL TUNING UP/DOWN
At radio mode, press ŹŹű/ŲŻŻ (13) for two seconds to activate the manual tuning mode.
At this manual tuning mode, press ŹŹű/ŲŻŻ (13) repeatedly to tune the radio frequency
upward or downward to your desired frequency. When a radio station signal is received,
pressing the preset number 1 – 6 (14) for 2 seconds can store the station on the respective
preset number. In case the manual tuning mode has not been operated for 5 seconds, it
will resume to automatic tuning mode.
AUTOMATIC SEEK UP/DOWN
At radio mode, press ŹŹű/ŲŻŻ (13) for automatic seeking the frequency upward or
downward to the next strong station received. By pressing the preset number 1 – 6 (14) for
two seconds can store the station on the respective preset number.
AUTO MEMORY STORE
At radio mode, press APS (15) for two seconds to start searching from the current
frequency and storing the strongest signal stations into the corresponding preset station
number 1 – 6 (14). The searching will stop until one cycle search is finished.
AUTO MEMORY SCAN
At radio mode, press APS (15) shortly to scan all the preset stations on the selected radio
band and stop for several seconds on each preset station scanned. During scanning, press
APS (15) again to stop this scanning and the current radio station will be broadcasted.
PRESET MEMORY
At radio mode, press any one of the preset number 1 – 6 (14) button to select a station
which had been stored in the memory. Press any one of the preset number 1 – 6 (14)
button for two seconds can store the current broadcasting station in the memory. This unit
can store up to 30 stations (FM1 x 6, FM2 x 6, FM3 x 6, AM1 x 6, AM2 x 6).
MONO / STEREO CONTROL
Press the MO/ST (9) to select stereo or mono mode. The desired mode “STEREO” or
“MONO” will appear on the LCD DISPLAY (5) shortly. When stereo signal is received,
stereo indicator will appear on LCD DISPLAY (5).
9
0$,181,7²',6&86%6'00&23(5$7,21
MODE SELECTION
During unit operation, press MOD (6) repeatedly to select the disc mode, USB input mode
and SD/MMC card input mode for your desired operation.
INSERT & EJECT OF DISC
To insert a disc, put it into the DISC SLOT (16), the unit will automatically insert the disc into
the mechanism and start playing. To eject the disc from the DISC SLOT (16), press the
(17) button and disc will automatically come out.
USB SLOT
Insert USB device to the USB SLOT (24) to play media files that recorded. The device will
have playback automatically after the USB device inserted.
SD / MMC CARD PORT
Insert SD or MMC card to the SD/MMC CARD PORT (25) to play media files that recorded.
The device will have playback automatically after the SD/MMC card inserted.
PLAY & PAUSE
At disc or USB/SD/MMC device playback mode, press Źűű(18) to pause playback and
“PAUSE” appears on the LCD DISPLAY (5). Press it again to resume to normal playback.
SELECT TRACKS
At disc or USB/SD/MMC device playback mode, press ŹŹű/ŲŻŻ (13) repeatedly to
choose tracks upward or downward for playback.
TRACK FAST FORWARD / FAST REWIND
At disc or USB/SD/MMC device playback mode, press and hold ŹŹű/ŲŻŻ (13) for two
seconds to fast forward or fast rewind the track. Press on time for x2, two times for x4, three
times for x8, four times for x20, 5 times for returning to normal playback. During fast
forward or fast rewind mode, press Źűű(18) to resume to normal playback.
REVIEW ALL TRACKS
At disc or USB/SD/MMC device playback mode, press INT (19) to play first 10 seconds of
each track of the disc or device. During intro play, “INT” appears on the LCD DISPLAY (5).
Press it again to stop intro play and playback will resume on the current track.
REPEAT PLAYBACK
At disc or USB/SD/MMC device playback mode, press RPT (20) to continuously repeat
playback the same track/chapter/title of the disc or device. During repeat playback mode,
“RPT” appears on the LCD DISPLAY (5). Press it again to stop this repeat playback.
10
0$,181,7²',6&86%6'00&23(5$7,21
RANDOM PLAYBACK
At disc or USB/SD/MMC device playback mode, press RDM (21) to play all tracks on disc or
device in random order and “RDM” appears on the LCD DISPLAY (5). Press it again to
resume to normal playback at the current track.
VIDEO SYSTEM SELECTOR
At video playback mode, press NUMBER BUTTON 5 (22) continuously to select the video
system in PAL / NTSC / AUTO modes.
AUDIO CHANNELS SELECTOR
At video playback mode, press NUMBER BUTTON 6 (23) continuously to select the audio
output channels that recorded in the devices.
Note
Depends on different type of discs and media files that recorded, not all operations as
described in the above operation manual can be functions.
11
5(027(+$1'6(7²&21752/6/2&$7,21
2
1
3
4
7
9
8
24
10
11
12
13
Remove this tab
before using the
remote control
14
15
17
16
6
18
20
19
23
21
22
25
26
27
5
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
Power On/Off Control
Play & Pause Control
Band Selector / OSD
Directional Keys
Menu
Enter / Confirm Key
TV System Selector /
LO/DX Selector
System Setup
Playback Setting Key
Sub-Title Selector
Disc/Track Repeat Control
Preset Equalization Control
Number Keys
Stop Mode
Sound Mute Control
Mode Selector
Clock Display & Adjustment
Title / PBC / AMS Control
Slowly Playback Control
MO/ST Selector / Channel
Selector / Language Selector
Fast Forward/Rewind Control
Tuning / Track Select Control
Audio & Video Control
Volume Control
Audio Files Playback
Photo Files Playback
Video Files Playback
Note
Printings & symbols on the above drawing may be varied from the exact remote control
handset. Referred to your remote control handset for exact functions & features that applied.
12
5(027(+$1'6(7²*(1(5$/23(5$7,21
13
5(027(+$1'6(7*(1(5$/23(5$7,21
POWER ON/OFF CONTROL ( )
Press
(1) to turn on the unit. Press it again to turn off the unit. All the memorized setting
will retain after the unit turned off. When the unit is turned off, press any one of the control
key can also turn on the unit.
MODE SELECTOR (MODE)
Press MODE (16) to choose your desired modes among radio, disc, USB input, SD/MMC
card input and auxiliary input operation.
VOLUME & AUDIO/VIDEO CONTROL (VOL+ / VOL– / SEL)
Repeatedly press VOL+ / VOL– (24) to increase or decrease the sound level. Press SEL
(23) to move the audio/video control through bass, treble, balance and fader. When the
desired mode is selected, pressing VOL+ / VOL– (24) to adjust the control level. When the
selected mode has not been adjusted for several seconds, it will return to its original
operating mode.
(Note: When preset equalizer control is activated, bass and treble will resume to its default
stage)
PRESET EQUALIZER CONTROL (EQ)
Repeatedly press EQ (12) to select your following desired audio equalization: Æ CLASSIC
Æ POP Æ ROCK Æ DSP OFF Æ
(Note: When preset equalizer control is activated, bass and treble will resume to its default
stage)
MUTE CONTROL (
)
Press (15) to cut down the sound output, press it again to release the mode and recover
to the previous volume level.
CLOCK DISPLAY & ADJUSTMENT (CLK)
During unit operation, press CLK (17) to recall the time display on LCD display. Press it
again or after 5 seconds, the LCD display will return to its original status.
Time Setting & Adjustment
During clock display, press and hold CLK (17) until the hour digit starts blinking. Press
VOL+ / VOL– (24) to adjust hour and confirm the setting by pressing SEL (23), it will then
change to minute setting. Press VOL+ / VOL– (24) to adjust minute and confirm the setting
by pressing CLK (17).
14
5(027(+$1'6(75$',223(5$7,21
MODE SELECTION (MODE)
During unit operation, press MODE (16) repeatedly to select the radio mode for radio
operation.
RADIO BAND SELECTOR (BAND)
During radio operation, press BAND (3) repeatedly to select the desired radio band in the
following order: > FM1 > FM2 > FM3 > AM1(MW1) > AM2(MW2) >
AUTO MEMORY STORE (A/PS)
During radio operation, press A/PS (18) for 2 seconds to start searching from the current
frequency and storing the strongest signal stations into the corresponding preset station
number 1 – 6 (13). The searching will stop until one cycle search is finished.
AUTO MEMORY SCAN (A/PS)
During radio operation, press A/PS (18) shortly to scan all the preset stations on the
selected radio band and stop for several seconds on each preset station scanned. During
scanning, press A/PS (18) again to stop this scanning and the current radio station will be
broadcasted.
MANUAL TUNING CONTROL (
ŹŹű
/
ŲŻŻ
)
During radio operation, repeatedly press ŹŹű/ŲŻŻ (22) for manual tuning the radio
frequency upward or downward
MANUAL SEEK CONTROL (
ŹŹ
/
ŻŻ
)
During radio operation, press ŹŹ
/
ŻŻ (21) to seek the radio frequency upward or
downward and stop when a radio station received. Fine tune the radio station by pressing
ŹŹű/ŲŻŻ (22) repeatedly.
PRESET STATIONS SELECTION (1 – 6)
During radio operation, press any one of the number keys 1 – 6 (13) to select a station
which had been stored in the memory. Press the desired number key for several seconds,
the current station broadcasting will be stored into this number key. The unit can store up to
30 stations: FM1 x 6, FM2 x 6, FM3 x 6, AM1 x 6, AM2 x 6
STEREO / MONO SELECTOR (MO/ST)
During radio operation, press MO/ST (20) to select FM reception in stereo or mono mode.
The desired mode “STEREO” or “MONO” will appear on the LCD display shortly. When
stereo signal is received, stereo indicator will appear on LCD display.
LOCAL / DISTANT SELECTOR (LO/DX)
During radio operation, press LO/DX (7) to switch between a local (LOCAL) setting for
reception of strong stations, and a distant (DX) setting for reception of weak stations.
15
5(027(+$1'6(7²
',6&86%6'00&,138723(5$7,21
MODE SELECTION (MODE)
During unit operation, press MODE (16) repeatedly to select the disc mode, USB input
mode and SD/MMC card input mode operation.
ON SCREEN DISPLAY (OSD)
During disc & USB/SD/MMC input operation, press OSD (3) to display the contents of the
current playing source on screen (an external device not included in this unit). Depends on
the disc or file type, it may display the disc type, title number, total title numbers, chapter
number, total chapter numbers, playing time, elapsed time as well as audio output channel.
PLAY / PAUSE CONTROL (
Źűű
)
During disc & USB/SD/MMC input playback mode, press Źűű(2) to pause playback. Press
it again to resume normal playback.
STOP MODE (STOP)
During disc & USB/SD/MMC input playback mode, press STOP (14) can stop the current
playback temporary, press it again will stop the playback in entirely. During temporary stop,
press Źűű(2) can resume the playback at current position.
TRACKS UP/DOWN SELECTION (
ŹŹű
/
ŲŻŻ
)
During disc & USB/SD/MMC input playback mode, repeatedly press ŹŹű/ŲŻŻ (22) to
choose tracks upward or downward. Press the number keys 0-9/+10 (13) can also select
the desired number of track for playback. The +10 (13) key is used to select track for every
10 tracks upward.
FAST FORWARD & FAST REWIND CONTROL (
ŹŹ
/
ŻŻ
)
During playback mode, press ŹŹ / ŻŻ (21) to fast forward or fast rewind the tracks.
Press one time for x2, two times for x4, three times for x8, four times for x20, 5 times for
returning to normal playback. During fast forward or fast rewind mode, press Źűű(2) to
resume normal playback.
SLOWLY PLAYBACK CONTROL (SLOW)
During video playback mode, press SLOW (19) to start playback in slow motion. Press one
time for 1/2 slow advance, two times for 1/3 slow advance, three times for 1/4 slow advance,
four times for 1/5 slow advance, five times for 1/6 slow advance. Six times for 1/7 slow
advance, seven times for returning to normal playback. During slow motion playback, press
Źűű(2) can resume to normal playback
REPEAT PLAYBACK (REPEAT)
During playback mode and depends on the type of disc or file recorded, press the REPEAT
(11) key continuously to repeat playback of the same chapter, title, track or the whole
device/disc. Press REPEAT (11) again to stop this repeat playback.
16
5(027(+$1'6(7²
',6&86%6'00&,138723(5$7,21
PLAYBACK SETTING KEY (GOTO)
During disc & USB/SD/MMC input operation mode, use GOTO (9) key for desired playback
setting on screen (an external device not included in this unit). Depended on the disc & file
type and at playback mode, press GOTO (9) key and by using the directional Ÿ/ź/Ż/Ź (4)
and ENTER (6) keys to set on screen the desired tracks, title, chapter or time for playback.
AUDIO CHANNEL SELECTION (
)
During disc & USB/SD/MMC playback mode, press (20) to select different audio output
channels that recorded in the device.
SUB-TITLE SELECTION (SUB-T)
During DVD & USB/SD/MMC playback mode, press SUB-T (10) to select different sub-title
that recorded on DVD or the devices.
TITLE / PBC / MENU SELECTOR (TITLE / PBC / MENU)
DVD Mode
At DVD playback mode, press TITLE (18) or MENU (5) to show on screen (an external
device not included in this unit) the menu of the entire disc. By using the Ÿ/ź/Ż/Ź (4) and
ENTER (6) keys to select and set on screen your desired mode and tracks for playback.
VCD Mode
At VCD playback mode, press MENU (5) will start the sequence playback at the beginning.
USB/SD/MMC Input Mode
At video & photo playback mode, press TITLE (18) will stop the playback and the screen
(external device not included in this unit) will show the chapter and title of the device that
played.
SYSTEM SETUP (SET UP)
During disc playback / USB input / SD/MMC card input mode, press SET UP (8) to start the
system set up. A setup menu appears on screen (the unit has to be connected to an
external screen that is not included in the unit). By using Ÿ/ź/Ż/Ź (4) and ENTER (6)
keys to make the setup of system, language, audio, video, speaker and digital output.
Press SET UP (8) again to resume the screen to its original status.
VIDEO SYSTEM SELECTOR
At video playback mode, press LO/DX (7) to select the video system in PAL / NTSC / AUTO
modes.
MEDIA SELECTOR
At playback mode, press the number key 4 / 5 / 6 (25 / 26 / 27) to shift playback among
audio files, photo files and video files respectively (available on disc or device with different
media files recorded).
Note
: Depends on different type of discs and media files that recorded, not all operations as
described in the above operation manual can be functioned.
17
63(&,),&$7,21
GENERAL
Power Requirement --------------------------------------------- DC 12 Volts, negative ground
Load Impedance ------------------------------------------------- 4 Ohms
Maximum Power Output --------------------------------------- 80 watts x 4 channels
Tone Control – Bass (at 100 Hz) ----------------------------
Treble (at 10 KHz) --------------------------
+/-8 dB
+/-8 dB
DISC SECTION
Disc Play ----------------------------------------------------------- DVD / VCD / MP3 / CD
Mounting Angle ---------------------------------------------------
+/- 30
VIDEO SECTION
Video System ----------------------------------------------------- AUTO / PAL / NTSC
Video Output Level ---------------------------------------------- 1.0Vp-p 75 Ohms
Horizontal Resolution ------------------------------------------- 500
AUDIO SECTION
Maximum Output Level ----------------------------------------- 2 Vrms (+/-3 dB)
Frequency Response ------------------------------------------- 20 Hz to 20 KHz
Signal to Noise Ratio ------------------------------------------- 85 dB
Channel Separation --------------------------------------------- 80 dB
AM RADIO SECTION
Frequency Range ------------------------------------------------ 530 – 1710 KHz
IF --------------------------------------------------------------------- 450 KHz
Usable Sensitivity (-20 dB) ------------------------------------ 25 dB
FM RADIO SECTION
Frequency Range ------------------------------------------------ 87.5 – 107.9 MHz
IF --------------------------------------------------------------------- 10.7 MHz
Usable Sensitivity (-20 dB) ------------------------------------ 15 dB
Signal to Noise Ratio ------------------------------------------- 60 dB
Stereo Separation (at 1 KHz) --------------------------------- 30 dB
Frequency Response ------------------------------------------- 30 Hz – 15 KHz
Note: Specification and design; functions and features; unit illumination; colour and display segment are
subject to change without prior notice. Photo or drawing as shown on gift box or operation manual might
be varied from the exact unit. Depends on the input devices, operation might be varied from the
operation manual described.
18
6,03/(7528%/(6+227,1**8,'(
352%/(06&$86(662/87,216
No power
- Check and make sure the connecting wires are connected correctly
- Check whether the fuse is blown. Replace with the proper value fuse if necessary.
No sound
- Check and make sure the speaker wires are connected correctly.
No picture
- Check whether the video wire is connected to the video device.
Unit hand-up
- Press the RESET button to reset the unit to its default stage.
No function when pressing the buttons
- Press the RESET button to reset the unit to its default stage.
Poor effect or unable to receive radio
- Check whether the radio antenna is inserted or properly connected.
- Antenna may not be the proper length. Make sure the antenna is fully extended.
- Antenna may be poorly grounded. Check and make sure the antenna is properly grounded.
Stereo cannot be received under radio mode
- Tune the radio frequency accurately.
- The broadcasting signal is too week, set the mode to MONO.
Disc inserted but cannot play
- Check whether the disc inserted upside down.
- Check whether the disc is dirty or badly cracked.
- Lens is dirty. Clean lens by using the lens clean disc.
Picture without colour or no sound under disc/USB/SD/MMC playback mode
- Improper setting of colour system. Set again to “PAL” or “NTSC”.
- The disc is dirty or damaged. Wipe the disc with a dry soft cloth or replace a new disc.
Abnormal moving, skipping or sound during playback
- The disc is dirty or damaged. Wipe the disc with a dry soft cloth or replace a new disc.
Remote handset does not work
- Replace new battery of the remote handset.
- Point the remote handset directly at the remote sensor of the main unit.
- Clean the surface of the remote sensor.
Note
After the above efforts, if the unit still cannot be worked normally, consult your service
dealer. Never attempt to disassemble the unit by yourself. No service part inside the unit.
19 IB-B049-0006-00
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Pyle PL94MU User manual
-
PYLE Audio PLCG53 User manual
-
PYLE Audio PLCD42M User manual
-
PYLE Audio PLCD44 User manual
-
PYLE Audio PLCD38 User manual
-
Radio Shack PLCD39 User manual
-
PYLE Audio PLCD45MP3 User manual
-
Pyle MIN-T66 User manual
-
-
PYLE Audio PLCDUSB78MP3 User manual
Other documents
-
Craig CD6961BT Owner's manual
-
Voyager MP5000 User manual
-
Orava AR-112 User manual
-
Pyramid Car Audio CD Player CDR88DFX User manual
-
RM RM-5777 Instruction & Owner's Manual
-
Lanzar VBD2300USBMP3 Owner's manual
-
Aiwa CDC-X126 Operating Instructions Manual
-
Premier SCR-5381USDR User manual
-
Boss Audio Systems 612UA User manual
-
Hyundai H-CMD4009 Black User manual
