Watlow Electric RAYMAX 1330 User manual

Watlow Electric
Brand
Watlow Electric
Model
RAYMAX 1330
Type
User manual

This manual is also suitable for

Watlow Electric RAYMAX 1330 is a radiant heater that features specially insulated heater emitter strips for higher performance. It has a rugged stainless steel construction that protects it from contaminants and eliminates the need for fragile glass or ceramic elements. The field replaceable emitter strips allow you to avoid the cost of buying a whole new radiant heater. It also has no reflectors, eliminating the need for cleaning or replacing. The one-inch thick backside insulation provides better heating efficiency.

The RAYMAX 1330 is suitable for applications such as thermoforming plastics and composites, circuit board soldering, heat shrinking of plastic, terminal box, thermowell, and mounting studs. It has a maximum watt density of 30 W/in2 and a maximum face temperature of 700°C (1300°F). The typical peak energy wavelength is 3 microns.

Watlow Electric RAYMAX 1330 is a radiant heater that features specially insulated heater emitter strips for higher performance. It has a rugged stainless steel construction that protects it from contaminants and eliminates the need for fragile glass or ceramic elements. The field replaceable emitter strips allow you to avoid the cost of buying a whole new radiant heater. It also has no reflectors, eliminating the need for cleaning or replacing. The one-inch thick backside insulation provides better heating efficiency.

The RAYMAX 1330 is suitable for applications such as thermoforming plastics and composites, circuit board soldering, heat shrinking of plastic, terminal box, thermowell, and mounting studs. It has a maximum watt density of 30 W/in2 and a maximum face temperature of 700°C (1300°F). The typical peak energy wavelength is 3 microns.

Aluminized Steel Insulation
Cap with 1 in. (25 mm) Thick
Insulation Blanket
High Performance
Mineral Insulation
Sin
uated
Element
Wire
High Emissivity
Coating
3 in. (76 mm) Wide
Replaceab
le Stainless
Steel Emitter
Stainless
Steel Case
RAYMAX
®
1330
RAYMAX
®
1330—
Features Specially
Insulated Heater
Emitter Strips for
Higher Performance
The RAYMAX
®
1330 is the only radiant heater that features
specially insulated heater emitter strips for higher performance.
Watlow developed a unique compacted mineral insulation to
electrically insulate the element wire, with a result of superior heat
transfer and higher operating capabilities.
Because of its rugged stainless steel construction, the RAYMAX
1330 will last longer. And this relatively new heater features a high
emissivity black coating and a uniform, full surface heat source for
better efficiency.
© 2005 Watlow Electric Manufacturing Company Printed in the USA on Recycled Paper, 15% Postconsumer Waste
Features and Benefits
Field replaceable emitter strips
• Allow you to avoid the cost of buying a whole new
radiant heater
Rugged metal construction
• Protects the heater from contaminants
No reflectors
• No cleaning or replacing
No fragile glass or ceramic elements
• No worries involved
One-inch thick backside insulation
• Provides better heating efficiency
12001 Lackland Road
St. Louis, Missouri 63146 USA
Phone:
+1 (314) 878-4600
FAX: +1 (314) 878-6814
Internet: www.watlow.com
e-mail: info@watlow
.com
STL-1330-0805
Applications
• Thermoforming plastics and composites
• Circuit board soldering
• Heat shrinking of plastic
•
T
er
minal box
• Thermowell
• Mounting studs
•
Thermocouple welded to hot face
How to Order
T
he RAYMAX 1330 and radiant band/strip emitters are
available made-to-order only. It is helpful to have the
following information available:
• Heated width and length (or diameter for band emitters)
•
Total wattage
• Voltage and phase
• Mounting studs, if desired
•
Mounting legs and leg height, if desired
• Terminal location
• Terminal box, if desired
• Thermocouple or thermowell, if desired
Availability
Made-to-Order:
Consult Watlow
2
15
/
16
in.
(74.6 mm)
L
Overall = Heated + 1
3
/
16
in.
5
/
32
in.
1
/
4
in.
3
/
4
in.
Optional
Type K
T/C
9
/
16
in.
2
9
/
16
in.
(65 mm)
Overall Width =
Heated Width
+
1
/
16
in.
(1.58 mm)
Overall Length =
Heated Length
+ 2 in.
(50.8 mm)
7
/
8
in.
(0.875 mm)
1
1
/
2
in.
(38 mm)
2
1
/
2
in.
(63 mm)
Heated width: 3.187 in (81 mm) 19.125 in (485.77 mm) 3.187 in (81 mm)
Length: 12 in (305 mm) 30.5 in (775 mm) any
HHeeaatteerr DDiimm.. MMiinniimmuumm MMaaxxiimmuumm IInnccrreemmeennttss
Radiant Band and Strip Emitters
Constructed using Watlow’s exclusive mineral insulation, rugged
stainless steel sheath and high emissivity coating, these heaters
can operate at temperatures to 700°C (1300°F), and 30 W/in
2
(4.7 W/cm
2
).
Applications
• Heating rotating drums and rollers
• Tube ovens
• Small spot heating
• Heat shrinking and curing wire coatings
• Heat laminating wheels
Sizes
Strip Emitters:
Width: 3 inches (76.2 mm)
Length: 6 inches (152.4 mm) min
31 inches (76.2 mm) max
Band Emitters:
Width: 1 inch (25.4 mm) min
2 inch (50.8 mm)
3 inch (76.2 mm) max
Applications and Technical Data
Sizes and Ratings
Thickness
• 2.562 inches (65 mm)
Volts
• 120, 240, 480VÅ(ac), 1-phase. 3-phase available on units
w
ith three or six emitters.
Maximum Watt Density
• 30 W/in
2
(4.7 W/cm
2
)
Maximum Face Temperature
• 700°C (1300°F)
Typical Peak Energy Wavelength
• 3 microns
To be automatically connected to the nearest North American Technical and Sales Office call:
1-800-WATLOW2
International
T
echnical and Sales Offices: China,
+86 (21) 5211-0231 • France
,
+33 (01) 3073-2425 • German
y
,
+49 (0) 7253-9400-0 •
Ital
y
,
+39 (02) 458-8841 • Japan, +81 (03) 3518-6630 • K
orea,
+82 (02) 575-9804 • Mala
ysia,
+60 (4) 641-5977 • Me
xico,
+52 (442) 217-6235 •
Singapore
,
+65 6773-9488 • Spain, +34 91 675 12 92 • Sweden, +46 31 7014959 • T
aiwan,
+886 (0) 7-288-5168 •
United Kingdom, +44 (0) 115-964-0777
  • Page 1 1
  • Page 2 2

Watlow Electric RAYMAX 1330 User manual

Watlow Electric
Brand
Watlow Electric
Model
RAYMAX 1330
Type
User manual
This manual is also suitable for

Watlow Electric RAYMAX 1330 is a radiant heater that features specially insulated heater emitter strips for higher performance. It has a rugged stainless steel construction that protects it from contaminants and eliminates the need for fragile glass or ceramic elements. The field replaceable emitter strips allow you to avoid the cost of buying a whole new radiant heater. It also has no reflectors, eliminating the need for cleaning or replacing. The one-inch thick backside insulation provides better heating efficiency.

The RAYMAX 1330 is suitable for applications such as thermoforming plastics and composites, circuit board soldering, heat shrinking of plastic, terminal box, thermowell, and mounting studs. It has a maximum watt density of 30 W/in2 and a maximum face temperature of 700°C (1300°F). The typical peak energy wavelength is 3 microns.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents