AMX MSA-RMK-07 Installation guide

Category
Mounting kits
Type
Installation guide

AMX MSA-RMK-07 lets you mount a 7" Modero S Series Wall/Flush Mount Touch Panel directly on an equipment rack. The kit includes a rack mount frame, screws, and washers for a stable installation mount.

Here are some of the key features and use cases for the AMX MSA-RMK-07:

  • Stable installation mount: The MSA-RMK-07 provides a secure and stable mounting solution for your Modero S Series Touch Panel, ensuring that it stays in place even in demanding environments.
  • Easy to install: The kit comes with all the necessary hardware and instructions, making it easy to install the rack mount kit in minutes.

AMX MSA-RMK-07 lets you mount a 7" Modero S Series Wall/Flush Mount Touch Panel directly on an equipment rack. The kit includes a rack mount frame, screws, and washers for a stable installation mount.

Here are some of the key features and use cases for the AMX MSA-RMK-07:

  • Stable installation mount: The MSA-RMK-07 provides a secure and stable mounting solution for your Modero S Series Touch Panel, ensuring that it stays in place even in demanding environments.
  • Easy to install: The kit comes with all the necessary hardware and instructions, making it easy to install the rack mount kit in minutes.
Installation Guide
MSA-RMK-07 7” Modero S Series
®
Rack Mount Kit
Overview
The MSA-RMK-07 Modero S Series
®
Rack Mount Kit (FG2265-15) is an optional accessory
for the MSD-701 7” Modero S Series Wall/Flush Mount Touch Panel (FIG. 1). The kit allows
the touch panel to be mounted directly on an equipment rack, and includes a rack mount
frame, screws and washers.
Product Specifications
Installation of the MSA-RMK-07
The MSA-RMK-07 offers a stable installation mount for the MSD-701 through the panel’s
Back Box.
NOTE: All doors, covers, and other obstacles preventing installation of the Rack Mount Kit
should be removed before installation is attempted. Due to the size of the Modero S Series
panel, it may not be possible to close racks that contain a rack door once installation is
complete.
To install the MSA-RMK-07:
1. Secure the Rack Mount Panel to the rack with #10 screws. Make sure that the
installation flanges (FIG. 2 and FIG. 3) face away from the front of the rack (FIG. 1).
2. Insert the Back Box into the Rack Mount Panel, making sure that the Back Box is in
the correct orientation. The stand-ups on the installation flanges will pass through the
Back Box and help anchor it in place.
3. Pass a washer through a #6 screw and insert it in a stand-up screw hole (FIG. 2).
Repeat this procedure at the opposite of the Back Box. Note that the Rack Mount
Panel has only two stand-ups, located opposite each other on the Installation flanges.
WARNING: The maximum recommended torque to be used on the Back Box installation
screws is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the screws, such as
with powered screwdrivers, can strip out the screw holes or damage the plastic back box.
.
4. With the Back Box anchored in the Rack Mount Panel (FIG. 4), you may now install the
MSD-701 into the Back Box.
NOTE: For more information on installing the MSD-701 into its back box, please refer to the
MXD/T-700 Operation Reference Guide, available from www.amx.com.
FIG. 1 MSA-RMK-07
MSA-RMK-07 (FG2265-15) Specifications
Dimensions
(HWD):
5.22” x 19.00” x 2.10” (13.26 cm x 48.26 cm x 5.33 cm)
Weight:
2.2 lbs (1 kg)
Included
Accessories:
MSA-RMK-07 Installation Guide (93-2265-15)
Rack Mount Panel, 7" Modero Wall Touch Panel (62-2265-20)
Screws, #10-32 x 625" Long, Black (4) (80-0186)
Washers, #2, Black Nylon (4) (80-0342)
Other AMX
Equipment:
MSD-701 7” Modero S Series Wall Mount Touch Panel (FG2265-02)
19.00” (48.26 cm)
5.22”
(13.26 cm)
2.11”
(5.33 cm)
Front View
Top View
Side View
5.22”
(13.26 cm)
2.11”
(5.37 cm)
Up
Installation
Flanges
Stand-Ups
Up
FIG. 2 Installation of the Back Box into the MSA-RMK-07, front view
FIG. 3 Installation of the Back Box into the MSA-RMK-07, rear view
FIG. 4 Final assembly of the MSA-RMK-07 with back box
Installation
Flange
Screws
Washers
Installation
Flange
Screws
Washers
Rack Mount Panel
Back Box
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
9/13
©2013 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2265-15 REV: A
A Note About Wall and Rack Installation
Some products are installed in areas of differing temperature and cooling methodologies.
These include products installed in walls, racks, cabinets, etc. Those areas may have
different temperatures and/or cooling approaches that must be taken into consideration to
maintain the product within the specified operating temperature.
FIG. 5 shows an AMX device installed in a wall with a filled volume (such as with insulation or
concrete), as well as with a closed volume (such as between studs in an otherwise finished
wall). The diagram shows how heat generated by the device or other devices may have no
way to escape, and may build up to levels that may affect device operation.
In FIG. 6, the diagram displays an AMX device in a typical rack mounting, with full air
circulation around the front and back of the device. In this case, the main concern is with heat
building up between components, possibly to levels that may affect device operation.
Installation Recommendations
During any installation, a lack of ventilation may produce conditions that may adversely affect
the device’s operation. In these circumstances, special care must be made to make sure that
temperatures within enclosed areas do not exceed the device’s maximum rated temperature.
FIG. 5 Heat convection in filled or closed volume, limited or no convection
FIG. 6 Heat convection in rack-mounted devices
  • Page 1 1
  • Page 2 2

AMX MSA-RMK-07 Installation guide

Category
Mounting kits
Type
Installation guide

AMX MSA-RMK-07 lets you mount a 7" Modero S Series Wall/Flush Mount Touch Panel directly on an equipment rack. The kit includes a rack mount frame, screws, and washers for a stable installation mount.

Here are some of the key features and use cases for the AMX MSA-RMK-07:

  • Stable installation mount: The MSA-RMK-07 provides a secure and stable mounting solution for your Modero S Series Touch Panel, ensuring that it stays in place even in demanding environments.
  • Easy to install: The kit comes with all the necessary hardware and instructions, making it easy to install the rack mount kit in minutes.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI