Ergotron 97-827 User guide
- Category
- Notebook arms & stands
- Type
- User guide
1 of 11
888-45-322-G-00 rev. C • 01/14
User's Guide
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド : 日本語
ENGLISH
For the latest User Installation Guide please visit: www.ergotron.com
Styleview LCD Height Adjustable
Keyboard Arm Accessory (SV4X)
2 of 11
888-45-322-G-00 rev. C • 01/14
ENGLISH
These symbols alert users of a safety condi-
tion that demands attention. All users should
be able to recognize and understand the
signifi cance of the following Safety Hazards
if encountered on the product or within the
documentation. Children who are not able
to recognize and respond appropriately to
Safety Alerts should not use this product with-
out adult supervision!
Hazard Symbols
Review
Symbol Signal Word Level of Hazard
NOTE
A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING
A WARNING indicates either potential for property dam-
age, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
Safety
Important! You will need to adjust this product and the cart after installation is complete. Make sure all your
equipment is properly installed on the product before attempting adjustments. This product should move
smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or
diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and
easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference.
Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted
load, you should repeat these adjustment steps to ensure safe and optimum operation.
WARNING: Keyboard tray can spring up when
lever is released.
WARNING: E-Brake cover could be broken if the keyboard arm
is panned and slammed into the stowed position.
3 of 11
888-45-322-G-00 rev. C • 01/14
< 3 lbs. (4.1 kg)
90°
12° 6" (152mm)
6' (152 mm)
6" (152mm)
17" (430 mm)
25.4" (645 mm)
23.7" (602 mm)
4.7" (120 mm)
4.7" (120 mm)
6" (152 mm)
4.7" (120 mm)
4.6" (117 mm)
9.6" (243 mm)
3.6" (91mm)
1.4" (35 mm)
6.6" (169 mm) 5" (127 mm)
4" (102 mm)
ENGLISH
Features & Specifi cations
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
4 of 11
888-45-322-G-00 rev. C • 01/14
2
ABC
1
8mm
8mm
1x
1x 1x
8x 8x
M4 x 25mm
M5 Nylock Nut
Alcohol Prep
Sterile
1x
PH2
ENGLISH
Components
Tools Needed
5 of 11
888-45-322-G-00 rev. C • 01/14
1
2
3
ENGLISH
Remove power brick holder if present.
Remove mouse holder.
Remove keyboard from tray.
6 of 11
888-45-322-G-00 rev. C • 01/14
4
a
b
5
M5 Nylock Nut
M5 Nylock Nut
4x
4x
8mm
8mm
8mm
ab
ENGLISH
a. Remove Phillips screws (8) using a PH2
Phillips screwdriver.
NOTE: Use a PH2 Phillips screwdriver to
remove these screws. Some force may
be required to remove these screws if red
loctite is present.
b. Remove 8 nuts to separate
keyboard tray from static
keyboard arm.
Install keyboard tray onto height adjustable keyboard arm using 8 nuts.
7 of 11
888-45-322-G-00 rev. C • 01/14
6
M4 x 25mm
PH2
8x
ENGLISH
Install height adjustable keyboard arm with keyboard tray back onto the cart using
8 Phillips screws.
NOTE: Torque these screws to a minimum of 13in lbs/1.2Nm
If there is a drawer on the cart, you'll need to adjust the keyboard
arm to fi t onto the cart.
Loosen lever and allow keyboard arm to fully extend.
WARNING: Keyboard tray can spring up when
lever is released.
8 of 11
888-45-322-G-00 rev. C • 01/14
9
ab
7
8
Alcohol Prep
Sterile
ENGLISH
NOTE: Keyboard and mouse cables need to be routed as shown. Wipe location with
alcohol pad before sticking the cable managment bracket to the keyboard arm
Attach power brick holder if removed.
Attach mouse holder.
9 of 11
888-45-322-G-00 rev. C • 01/14
10
ENGLISH
NOTES: Be careful when moving the keyboard arm through its range of motion. The keyboard tray can hit the
head unit, mouse ledge, or brick bracket if attached.
Downward travel of this arm is limited to 4" when drawers are installed.
Adjust the height of the keyboard arm.
WARNING: Keyboard tray can spring up when
lever is released.
WARNING: E-Brake cover could be broken if the keyboard arm
is panned and slammed into the stowed position.
10 of 11
888-45-322-G-00 rev. C • 01/14
11
14mm (9/16")
a
b
ENGLISH
Adjustment Step
Release Brake to move riser.
Lift – Up and down
NOTE: Adjustment may require
40 - 60 revolutions.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Important! You will need to adjust this product and the cart after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of
motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the
adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many
turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the
mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
11 of 11
888-45-322-G-00 rev. C • 01/14
ENGLISH
For local customer care phone numbers visit: http://contact.ergotron.com
NOTE: When contacting customer service, refer-
ence the serial number.
Learn more about ergonomic computer use at:
www.computingcomfort.org
Set Your Workstation to Work For YOU!
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain at.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Ergotron 97-827 User guide
- Category
- Notebook arms & stands
- Type
- User guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ergotron 33-387-194 User guide
-
Ergotron LearnFit Installation guide
-
-
Ergotron 97-926-064 User guide
-
-
Ergotron 97-942 User guide
-
-
-
-