ADC Optical Normal Through Panel Pro Patch User manual

Brand: ADC

Model: Optical Normal Through Panel Pro Patch

Category: Patch panels

Type: User manual

This manual is also suitable for

Pro Patch

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 • 1 - 8 0 0 - 3 6 6 - 3 8 9 1

SPEC SHEET

Pro Patch

Optical Normal Through Panel

ADC’s Optical Normal Through Panel is the latest addition to its Pro Patch line of broadcast

patching products. This fiber panel is designed to provide patch by exception, normal through

functionality, similar to copper-based patch panels. Traditional fiber patch panels require a fiber

jumper to be in place at all times. With this newly designed panel, however, all fiber “Source”

and “Destination” connections are on the rear of the panel, with a normal through connection

between the “Source” and “Destination” ports. For greater convenience and reliability, patch and

monitoring capabilities are accessed on the front of the panel.

Module Front Module Rear Chassis Open

Features

Two density options:

• The 3RU chassis houses 6 modules to

provide 24 fiber terminations (12 pairs)

using simplex connectors (SC, FC, ST).

• The 4RU chassis houses 6 modules to

provide 48 fiber terminations (24 pairs)

using small-form-factor connectors (LC).

Functionality:

• Each module contains pairs of “Source” and

“Destination” fibers plus optional monitor

ports and a switch for emergency patching.

• Accommodates 1310 and 1550 singlemode

wavelengths (switch wavelength range is

1290-1330 and 1525-1610).

• Connector ports on front and rear may be

SC, FC, ST or LC.

• IL through module is approximately 0.5 dB

(final specifications TBD).

• Module port is configurable to 90/10, 95/5

or 99/1 split ratios.

Module specifications:

• Modules may be added to the chassis

as needed.

• “Source” and “Destination” terminations

may be made by either splicing raw cable

to pigtails attached to the modules or by

routing connectorized patch cords to the

back of the modules.

• Manual switch on front of module to

change to “Patched” operation.

• LED indicators for “Normal” and

“Patched” operations.

• Modules are available with or without

monitor ports on the front.

Chassis specification:

• 19" EIA flush mounting

• Hot swappable power supply

to power switches inside modules

• 110/220 IEC interface

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 • 1 - 8 0 0 - 3 6 6 - 3 8 9 1

Pro Patch

Optical Normal Through Panel

Module Schematics

The new Pro Patch Optical Normal Through Panel provides patch by exception, normal through functionality.

Fiber “Source” and “Destination” connections are located on the rear of the panel, with a normal through

connection between the “Source” and “Destination” ports. To enable patching functionality, a fiber patch

cord is plugged into the front of the panel and a switch is flipped.

9 / 0 6 • 1 0 3 4 4 7 A E

Pro Patch

Optical Normal Through Panel

A Source

A Destination

B Source

B Destination

90%

Monitor

Patched

90%

10%

Monitor

Source

Destination

Back of Module Front of Module

Switch

90/10 Tap

Switch

A Source

A Destination

B Source

B Destination

90/10 Tap

90%

10 %

Monitor

Normal

Switch

90/10 Tap

90%

10%

Switch

Monitor

Source

Destination

Back of Module Front of Module

Description Catalog Number

Empty chassis with power supply

3 RU chassis with power supply and IEC cord, patch cord storage in rear

3 RU chassis with power supply and IEC cord, splice tray area in rear

4 RU chassis with power supply and IEC cord, patch cord storage in rear

4 RU chassis with power supply and IEC cord, splice tray area in rear

Power supply

Replacement power supply with IEC cord

PPO-3RU-P

PPO-3RU-S

PPO-4RU-P

PPO-4RU-S

PPO-PWR

O r d e r i n g I n f o r m a t i o n

These are preliminary specifications.

Call an ADC distributor for more details. To find a distributior near you visit adc.com/partners.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 • 1 - 8 0 0 - 3 6 6 - 3 8 9 1

The information below explains the ordering numbers contained in the charts on this page.

Pro Patch

Optical Normal Through Panel

Pro Patch™ Preconfigured Panels

9 / 0 6 • 1 0 3 4 4 7 A E

Pro Patch

Optical Normal Through Panel

Modules Loaded

1-6 Number of modules loaded

Catalog Number

PPO - __ __ __ __ __ __ __ __ - __

Panel Size

3 3 RU

4 4 RU

Rear Cable Management/splice

0 Patch cord slack storage

2 Heat shrink splice trays

3 Mass Fusion splice trays

Power Supply

0 No cord

1 With IEC cord

Rear Connector/Splice

2 SMFC

7 SMSC

J SMSC (8º angled polish)

8 SMLC (4 RU only)

0 Pigtail for splicing

4 SMST

Monitor Split Style

0 No monitor

A 90/10

B 95/5

C 99/1

Front Patch Connector Style

2 SMFC

7 SMSC

J SMSC (8º angled polish)

8 SMLC (4 RU only)

4 SMST

Switch Type

0 Standard individual

2 Pair switch together

Monitor Port Connector

0 No monitor

F SMFC (8º angled polish)

J SMSC (8º angled polish)

Q SMALC (4 RU only)

Custom configurations are available. Please contact ADC Technical Assistance Center.

SPEC SHEET

Pro Patch™ Modules

The information below explains the ordering numbers contained in the charts on this page.

Catalog Number

PPO-M __ __ __ __ __ __

Panel Size

3 3 RU

4 4 RU

Front Patch Connector Style

2 SMFC

7 SMSC

J SMSC (8º angled polish)

4 SMST

8 SMLC (4 RU only)

Switch Type

0 Standard individual

2 Pair switch together

Monitor Port Connector

0 No monitor

F SMFC (8º angled polish)

J SMSC (8º angled polish)

Q SMALC (4 RU only)

Rear Connector/Splice

7 SMSC

J SMSC (8º angled polish)

8 SMLC (4 RU only)

0 Pigtail for splicing

4 SMST

2 SMFC

Monitor Split Style

0 No monitor

A 90/10

B 95/5

C 99/1

Web Site: www.adc.com

From North America, Call Toll Free: 1-800-366-3891 • Outside of North America: +1-952-938-8080

Fax: +1-952-917-3237 • For a listing of ADC’s global sales office locations, please refer to our Web site.

ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101

Specifications published here are current as of the date of publication of this document. Because we are continuously

improving our products, ADC reserves the right to change specifications without prior notice. At any time, you may

verify product specifications by contacting our headquarters office in Minneapolis. ADC Telecommunications, Inc.

views its patent portfolio as an important corporate asset and vigorously enforces its patents. Products or features

contained herein may be covered by one or more U.S. or foreign patents. An Equal Opportunity Employer

Custom configurations are available. Please contact ADC Technical Assistance Center.

ADC Optical Normal Through Panel Pro Patch User manual

Brand: ADC

Model: Optical Normal Through Panel Pro Patch

Category: Patch panels

Type: User manual

This manual is also suitable for

Pro Patch

Download PDF

report

ADC Optical Normal Through Panel Pro Patch User manual

This manual is also suitable for

ADC Optical Normal Through Panel Pro Patch User manual

Related papers

Other documents