C2435M-A (2/03)
CLCLD5HD Series
Lower Dome for Heavy-Duty Spectra
®
Systems
®
DESCRIPTION
The following are lower domes for the Heavy-Duty Spectra and feature tamper-resistant hardware
and an aluminum trim ring.
Models
CLCLD5HDF-1 Standard clear dome for the CC5BCBW-HF1 Heavy-Duty Spectra system
CLCLD5HDBF-1 Heavy-Duty clear dome for the CC5BCBW-HBF1 Heavy-Duty Spectra system
CLCLD5HDPG-1 Standard clear dome for the CC5BCBW-HP Heavy-Duty Spectra system
LD5HDPG-1 Heavy-Duty clear dome for the CC5BCBW-HBF1 Heavy-Duty Spectra system
INSTALLATION
Pendant Models
Refer to Figure 1.
1. Lightly apply O-ring lubricant to the
O-ring. Install the O-ring in the groove
on the trim ring of the lower dome.
2. Attach the back box trim leash to a re-
tainer screw inside the lower dome.
3. Environmental Models Only – Plug the
two-pin heater connection in the lower
dome into the mating connector in the
back box.
4. Align barrel locks in lower dome with the
holes located on each side of the back
box. Push the lower dome onto the back
box. Press the center pins of the barrel
locks in to secure the lower dome.
In-Ceiling Models
Refer to Figure 2.
1. Attach the back box trim leash to one of
the 8-32 x .275-inch screws that secure
the back box to the mounting ring.
2. Align ball studs (located on the mount
ring) with the ball stud receivers (located
on the inside of the lower dome).
3. Place the lower dome over the back
box.
4. Push the lower dome over the back
box, line up the mounting screw
holes. Use the tamper-resistant
screws and the tool bit supplied with
the ceiling panel (CLCD5-P), and
attach the lower dome to the back
box.
MAINTENANCE
Clean the acrylic dome as needed. Be careful not to scratch the surface of the dome. Use a non-
abrasive cleaning cloth and agent that is safe for acrylic plastic.
Figure 1. Lower Dome Installation,
Pendant Models
Figure 2. Lower Dome Installation,
In-Ceiling Models
TRIM
LEASH
O-RING
BARREL
LOCK
00994
3500 Pelco Way
Clovis, CA 93612-5699
USA
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
International Customers:
Tel +1(559) 292-1981
FAX +1(559) 348-1120
www.pelco.com
REVISION HISTORY
Manual # Date Comments
C2435M 7/01 Original version.
C2435M-A 2/03 Revised per ECO#01-7241. Barrel locks replaced with tamper-resistant screws on in-ceiling models.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 2003, Pelco.
Endura and ExSite are trademarks of Pelco. All rights reserved.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex
®
Series products (multiplexers, server, and keyboard).
• Three years on Camclosure
®
and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
•Two years on standard motorized or fixed focal length lenses.
•Two years on Legacy
®
, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
•Two years on Spectra
®
, Esprit
®
, ExSite
™
, and PS20 scanners, including when used in
continuous motion applications.
•Two years on Esprit
®
and WW5700 Series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura
™
Series distributed network-based video products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
/