Avaya Accessory Connection Module Installation guide

Brand: Avaya

Model: Accessory Connection Module

Type: Installation guide

N0023532 Page 1 of 5 Standard 2.00

Accessory Connection Module Installation Guide

This document describes how to install the Accessory Connection Module (ACM) (NTMN71xx). The ACM is an

optional hardware module that you install into the telephone footstand. The ACM provides a port, or ports, to connect

the accessory cartridge interface.

The

3902 has one accessory port. The 3903, 3904, and 3905 have two accessory ports.

Note: The

3901 does not support the ACM.

The plug-in cartridge allows the

3900 Series Digital Telephones to use the following accessories:

• Meridian External Alerter and Recording Interface (MEARI)

• Personal Directory PC Utility (

3904 and 3905)

• Full Duplex Handsfree (FDHF) cartridge (

3904 Phase III only)

•Analog Terminal Adapter (ATA)

• Computer Telephony Integration Adapter (CTIA)

Note: The Meridian SL-100 does not support the CTIA.

Figure 1: Accessory Connection Module (ACM)

553-8967

ACM

Footstand

ACM ribbon cable

Rectangular

opening for

ACM Installation

Telephone and footstand









Standard 2.00 Page 2 of 5 N0023532

Accessory Connection Module Installation Guide

Installing the

Accessory

Connection

Module

1. Press the release latch on the back of the telephone.

2. Pull the footstand away from the back of the telephone.

3. Disconnect the line cord from the base of the telephone.

4. Move the telephone down 7 mm (1/4 inch), then use the hinges to swing the telephone

footstand away from the base of the telephone.

5. Snap the ACM into the rectangular opening in the telephone footstand. Ensure that it is

snapped in securely.

6. Plug the ACM cable connector into the back of the telephone.

7. Place the ACM attached ribbon cable into the track running down the telephone base.

8. Snap the plastic cable cover in place over the ACM ribbon cable.

9. Connect the line cord into the base of the telephone.

10. Connect the hinges to the telephone base and swing the footstand back in place.

11. Snap the footstand into a fixed position.

12. Return the telephone to its original position.

You can access the ACM connector ports through a cutout on the base of the footstand. When you are ready to attach

an accessory, insert your selected accessory cartridge into the ACM.

There are two ports at the back of the telephone footstand on the

3903, 3904, and 3905. Each port can sup-

port one cartridge accessory. The

3903, 3904, and 3905 can use a maximum of two cartridge accessories.

The

3902 supports one cartridge accessory.

Accessory

compatibility

The ACM provides up to two port connections. Some port types are not compatible. For

example, you cannot simultaneously use two data accessories that require a serial port.

The shape and size of the plug-in accessory cartridge prevents you from accidentally con-

necting incompatible accessories. If you are purchasing two accessory cartridges, refer to

Table 1 on page 3 to see if you can use the two accessories with the

3903, 3904, or

3905 at the same time. The 3902 supports only one accessory. See Table 1 on page 3

before you purchase optional hardware accessories.

Note: Not all accessories are supported on all telephones in the

3900 Series portfolio.

Contact your

Avaya distributor for further information.

N0023532 Page 3 of 5 Standard 2.00

Accessory Connection Module Installation Guide

Figure 2: Accessory cartridge

Table 1: Accessory compatibility

ATA CTIA PC Utility FDHF MEARI

Analog Terminal Adapter (ATA)

N/A Yes Yes No Yes

Computer Telephony Integration Adapter

(CTIA)

Yes N/A

Yes

N/A Yes

Personal Directoty PC Utility

Yes

N/A Yes Yes

Full Duplex Handsfree (FDHF)

Yes Yes N/A

Yes

Meridian External Alerter and Recording

Interface (MEARI)

Yes Yes Yes

Yes

N/A

Key-Based Accessory (KBA)

Yes Yes Yes Yes Yes

Display-Based Accessory (DBA)

Yes Yes Yes YeS Yes

Note 1. If either the CTIA or the PC Utility cartridge is installed, no additional cartridge is required. The applicable

software may be purchased separately.

Note 2. FDHF works with the MEARI external alerter functionality; however, the MEARI cannot be used for recording

when FDHF is in operation.

Note 3. FDHF and ATA can be interchanged but cannot be used simultaneously.

553-9154

RS232C

Latch

Standard 2.00 Page 4 of 5 N0023532

Accessory Connection Module Installation Guide

Wall transformers

You need a wall transformer that connects to the ACM to use accessory cartridges.

Contact your

Avaya distributor for further information.

The ACM requires one of the following wall transformers to power the accessory car-

tridges:

• 110 V wall transformer (NTMN80AA)

• EU (EMEA) 230 V wall transformer (NTHC09AA)

• UK 230 V wall transformer (NTHC08AA)

To connect the wall transformer:

1. Insert the accessory cartridge into the ACM. Refer to your accessory installation

guide.

2. Plug the wall transformer into an electrical outlet.

3. Connect the adapter plug, attached to your transformer, into the wall jack.

4. Connect the six-conductor line cord from the telephone to the adapter jack attached

to the wall transformer.

Figure 3: Adapter and wall transformer connections for North America

To IDF

6-conductor

line cord

from telephone

Adapter jack

Adapter

plug

553-9042

123

Plug

Jack

Adapter

Wall

transformer

(110 V or 220 V)

N0023532 Page 5 of 5 Standard 2.00

Accessory Connection Module Installation Guide

Figure 4: EMEA transformer

553-9042

123

Plug

Jack

Adapter

Wall

transformer

(110 V or 220 V)

Avaya Accessory Connection Module Installation guide

Avaya Accessory Connection Module Installation guide

Avaya Accessory Connection Module Installation guide

Related papers

Other documents