H67
© 2008 AS America Inc.
RENAISSANCE™ WHIRLPOOL
AND BATHING POOL
HIGH GLOSS
Revised 2/08
RENAISSANCE™ WHIRLPOOL
AND BATHING POOL
Comfortable bathing design with form-tted
backrest and molded-in armrests
❏ 2732.018 Whirlpool featuring System I
• Acrylic with berglass reinforcement
• Factory installed and tested whirlpool system
• 1.25 HP single speed, self-draining pump/motor
• Factory-installed power cord with plug
• Six multi-directional color-coordinated
jets including two in back rest area
• One color-coordinated air volume control
• Deck-mounted, color-coordinated air switch
On/Off control
• Dual, molded-in arm rests
❏ 2732.002 Bathing Pool Only
Nominal Dimensions:
1524 x 832 x 502mm
(60" x 32-3/4" x 19-3/4")
Compliance Certications -
Meets or Exceeds the Following Specications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SEE REVERSE FOR PRODUCT DIMENSIONS
AND SPECIFICATIONS
To Be Specied - Required:
❏ Bath Filler: (specify nish)
❏ Bath Drain: 1583.470 (specify nish)
To Be Specied - Optional:
❏ 5 Foot Apron: 9260.018 (specify color)
❏ Universal Tile Bead Kit: 751755-100
❏ Grab Bar Kit: 9822.200-two per kit (specify nish)
For color/nish availability and other faucet choices, please
see the Product Selector and Pricing Guide.
H68
© 2008 AS America Inc.
RENAISSANCE™ WHIRLPOOL
AND BATHING POOL
HIGH GLOSS
Revised 2/08
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION.
SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3 WALL TILING BEAD. KIT AND APRON No.9260.018 AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
60"
(1524mm)
33"
(838mm)
5-7/8"
(149mm)
12"
(305mm)
6"
(152mm)
3"
(76mm)
8-1/2"
(216mm)
16-1/2"
(419mm)
33"
(838mm)
19-3/4"(H)
(502mm)
18-1/4"(C)
(464mm)
C/L OF
OVERFLOW
16-1/2"
(419mm)
CUT OUT IN FLOOR
FOR DRAIN
DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE
OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.
60 x 32-3/4 x 19-3/4 In.
(1524 x 832 x 502mm)
65 Lbs. (29 Kg.)
524 Lbs. (237 Kg.)
55 Gal. (208 L.)
41 Gal. (155L.)
40-1/2 x 20-1/2 In.
(1029mm x 521mm)
52-1/2 x 26-1/2 In. (1334mm x 673mm)
13-3/4 In. (349mm)
38 Lbs./Sq. Ft. (187 Kgs/Sq. m.)
GENERAL SPECIFICATIONS FOR 2732 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.25 HP, 9.7 AMPS, 120V.PUMP
60 x 32-3/4 x 19-3/4
(1524 x 832 x 502mm)
GENERAL SPECIFICATIONS FOR 2732 BATHING POOL
51 Lbs. (23 Kg.)
509 Lbs. (230 Kg.)
55 Gal. (208 L.)
40-1/2 x 20-1/2 In. (1029 x 521mm)
52-1/2 x 26-1/2 In. (1334 x 673mm)
13-3/4 (349mm)
37 Lbs./Sq.Ft. (182 Kgs./Sq.m)
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
-
1
-
2
American Standard Whirlpool and Bathing Pool 2732.002 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard 2771018W.020 User manual
-
American Standard 6000.STE2 User manual
-
-
-
-
-
-
-
-
American Standard 2774.018W User manual
