CURT 45048 Installation guide

Type
Installation guide

CURT 45048 is a 2 1/2 inch receiver tube extension that can be used to extend the length of your vehicle's receiver hitch. It has a gross load capacity of 6,000 lbs when used as a weight carrying hitch at 34 inches, and 8,000 lbs at 24 inches. It also has a trailer weight capacity of 600 lbs at 34 inches, and 800 lbs at 24 inches. The receiver tube extension comes with a 5/8" hitch pin and clip, and it can be installed in just a few minutes. It is important to note that you should not exceed your vehicle's recommended towing capacity when using this product.

CURT 45048 is a 2 1/2 inch receiver tube extension that can be used to extend the length of your vehicle's receiver hitch. It has a gross load capacity of 6,000 lbs when used as a weight carrying hitch at 34 inches, and 8,000 lbs at 24 inches. It also has a trailer weight capacity of 600 lbs at 34 inches, and 800 lbs at 24 inches. The receiver tube extension comes with a 5/8" hitch pin and clip, and it can be installed in just a few minutes. It is important to note that you should not exceed your vehicle's recommended towing capacity when using this product.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS.
TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY A STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
34"- 6,000 LBS, 24"- 8,000
34"- 600 LBS, 24"- 800
30
2
2 1/2 INCH RECEIVER TUBE EXTENSION
3/10/2011
45048
4
NO DRILLING REQUIRED
Parts List
DESCRIPTIONPART NUMBERQTYITEM
5/8" HITCH PIN & CLIP
F-511
SAFETY CHAINS
SOLD SEPARATELY
VEHICLE RECEIVER HITCH
TOOLS REQUIRED
HACK SAW
1. Trim receiver tube extension at dotted line on sticker if used at 24".
2. Slide receiver tube extension into 2 1/2" receiver tube, install hitch pin and clip as shown. Attach safety
chain from vehicle to receiver tube extension safety chain loop.
3. Place desired ballmount in end of receiver tube extension and install hitch pin and clip.
4. Attach trailer to ballmount along with the trailers safety chains to receiver tube extension chain plate,
and plug in trailer lights. (NOTE: Trailer lights may require wire extensions.)
HITCH PIN
SOLD SEPARATELY
  • Page 1 1

CURT 45048 Installation guide

Type
Installation guide

CURT 45048 is a 2 1/2 inch receiver tube extension that can be used to extend the length of your vehicle's receiver hitch. It has a gross load capacity of 6,000 lbs when used as a weight carrying hitch at 34 inches, and 8,000 lbs at 24 inches. It also has a trailer weight capacity of 600 lbs at 34 inches, and 800 lbs at 24 inches. The receiver tube extension comes with a 5/8" hitch pin and clip, and it can be installed in just a few minutes. It is important to note that you should not exceed your vehicle's recommended towing capacity when using this product.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI