Viking FDFB5302R Installation guide

Type
Installation guide
INSTALLATION
INSTRUCTIONS
TOP-30, TOP-36, TOP-42, TOP-48
TOP PANEL KIT
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662)455-1200
For Use with Built-In Refrigerator/Freezers and Full Height Wine Cellars
IMPORTANT - PLEASE READ AND FOLLOW
•Before beginning, please read these instructions completely and carefully.
•Do not remove permanently affixed labels, warnings or plates from the product. This may void the warranty.
•Please refer to installation instructions included with the product for site preparations and considerations.
•The installer should leave instructions with the consumer who should retain for local inspector's use and for future
reference.
CAUTION: Always wear gloves when handling top and side panels. Some edges may be sharp enough to cause injury
during handling.
WARNING!
The unit must be fastened to a wall located at the rear of the product. Failure to properly fasten the product
to the wall can result in death or serious injury. See installation instructions included with the product for
proper securing methods.
Parts Included: Required Tools:
(1) Stainless steel top panel Electric drill
(6) Stainless steel wafer head screws (Part number - M0210417) 9/64" (.36 cm) diameter drill bit
(2) Wood screws (min 1.5" long) (Part number - PD020016)
To install top panel with two side panels:
1. The top panel will be fastened to an adjacent wall that is to be located behind the unit. This is to provide an anti-
tip device in lieu of the product being placed into a fixed enclosure. The unit should be anchored to wall studs
(minimum of two). Before positioning the unit in place, locate the wall studs.
2. Locate the unit in front of the area in which it is to be installed (approximately two feet directly in front of the final
position).
3. Place the top panel on top of the unit.
4. Position the side panels behind the cabinet side trim such that the top flanges of the side panels overlap the top
panel.
5. Insure that side panels are fully located behind the side trim and that the rear flanges of the panels are making
contact with the rear of the unit. (figure 1)
6. Using the 6 stainless steel wafer head screws, attach the side panels to the top panel by screwing through the side
panels into the top panel on each side (figure 2)
Side panel
goes behind
trim
Figure 1 Figure 2
VIKING RANGE CORPORATION
111 Front Street • Greenwood, Mississippi 38930 USA (662) 455-1200
Specifications subject to change without notice
For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at www.vikingrange.com
F20235A EN (030211 )
Figure 4
7. Using the panel hole locations as a template, drill ten (10) holes on the cabinet rear with a 9/64" (.36 cm) diameter
drill bit. (figure 3)
8. Attach the panel to the rear of the unit using the ten (10) black #8 sheet metal screws provided.
9. Plug unit into the receptacle and roll the unit so that the rear of the unit makes contact with the wall in the final
location.
10. Adjust to desired height, and level unit by turning the front and rear leveling wheel bolts clockwise to raise the unit
and counterclockwise to lower the unit. Rotate leveling feet until firmly in place against the floor. The unit back
should be tightly located against the back wall.
11. Using the top panel rear flange as an attachment device, locate holes in the flange that are aligned with a
minimum of two wall studs. (figure 4)
12. Using wood screws that are a minimum of 1½" long, attach the top panel flange to the anchoring device (wall
studs or other mechanical device). Ensure that the screw heads will not pull through slots in top panel. Use
washer if necessary to prevent pull through.
Screws
Wall
Studs
Figure 3
(Rear of unit)
Panel hole
locations
  • Page 1 1
  • Page 2 2

Viking FDFB5302R Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI