r
o
This tripod lets you secure the R-09HR in place at the angle you want. A cushion that dampens vibration is built into the screw hole
n the back o
the dedicated cover, absorbing vibration
rom the
oor and reducing unwanted noise
Extend the le
s of the tripod
ompletely and lift the lock lever
to re
ease t
e
oc
Orient t
e tripo
so t
at its
o
o
aces u
, then
osition it so that
t
e
egs are on t
e same si
e as
the micro
hone.
Cover Stand Set for
OP-R09HR-C
Owner’s manual
Before using this product, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” These sections
provide important information concerning the proper operation of the product. Additionally, in order to feel assured that you have
gained a good grasp of every feature provided by your new product, Owner’s manual should be read in its entirety. The manual should
be saved and kept on hand as a convenient reference.
e
ca
e
over
This protects the R-09HR
rom damage and prevents inadvertent operation while
ou’re carr
ing it inside a bag
Orient as shown in the gure and
nsert t
e R-09HR into t
e cover.
To keep it from falling out, fasten
t
e two
utton snaps s
own
y
t
e arrows
f you’re using a commercially available
trap, pass it through the ring
Open the tripod legs completel
.
djust the angle, then lower the
ever at t
e position w
ere you
want to secure t
e unit in p
ace
ote that reversing the orientation o
he legs may cause the unit to tip over
Ti
ten t
e screw.
ING THE
NIT
AFELY
Do not open or per
orm any internal modi
ica-
ions on the product
Do not attempt to repair the product, or re-
ace parts wit
in it (except w
en t
is manua
rovides speci
ic instructions directing you to
do so). Refer all servicing to
our retailer, the
earest Ro
an
Service Center
or an aut
o-
ized Roland distributor
In households with small children
an adult
hould provide supervision until the child is
capable o
ollowing all the rules essential
or
he sa
e operation o
the product.
Protect the product
rom strong impact. (Do
ot
rop it!)
Tr
to prevent cords and cables from becom-•
ing entang
e
. A
so, a
cor
s an
ca
es
hould be placed so they are out o
the reach
f
hil
r
n
Keep t
e a
apter screw inc
u
e
wit
t
e •
o
tiona
Mic Stan
A
a
ter (OP-R09M) in a
a
e place out o
children’s reach, so there is no
chance of it being swallowed accidentall
MP
RTANT N
TE
Do not expose t
e pro
uct to
irect sun
ig
t,
place it near devices that radiate heat, leave
t insi
e an enc
ose
ve
ic
e
or ot
erwise
sub
ect it to temperature extremes. Excessive
heat can deform or discolor the product
Be sure the tripod is spread out adequately.
is a
ows t
e tripo
to stan
wit
reater
stability.
se the setu
in a
lat, level location.
se the setup only a
ter con
irming the
stabilit
of all attached devices. Avoid use in
ocations w
ere win
or ot
er con
itions ma
ause the e
ui
ment to to
le and
all
Always detach the device
rom the tripod
before moving it. Carr
ing the device while
t is sti
attac
e
to t
e tripo
may cause t
e
evice to separate
rom the tripod and
all
Do not leave the device attached to the tri
od.
he topple and fall, resultin
in unanticipated
amage to t
e pro
uct
ake care not to allow fin
ers to become•
pinched when extending and retracting the
tripo
e
s
Roland assumes no liability whatsoever for an
amages, loss o
income, or claims b
an
third
arty arising
rom the inappropriate use o
this
ro
uct
Roland assumes no liability whatsoever for an
amage to the device resulting
rom the product
roppin
or fallin
Maintenance
or every
ay c
eaning wipe t
e pro
uct wit
so
t, dry cloth or one that has been slightly
am
ene
wit
water. To remove stu
orn
irt, use a cloth impregnated with a mild,
non-abrasive deter
ent. Afterwards, be sure
to wipe the product thoroughly with a so
t,
r
cloth.
ever use benzine, thinners, alcohol or
solvents of an
kind, to avoid the possibilit
o
iscoloration and
or de
ormation.
Speci cations
D
i
v
ain material: Polyurethan
Tri
od
(two-stage exten
ing/retracting type
etracted len
th: 98 mm/3.9 inches
Overall height in use (Approx. ):
90 mm/3.5 inc
es
Wei
t: 35
/1.2 oz
ax. capacit
for loaded weight:
1000 g
35.3 oz
In the interest of
roduct im
rovement, the
s
eci
ications and/or a
earance o
this
roduct
re sub
ect to chan
e without prior notice.
Attac
t
e microp
one stan
a
apter to t
e microp
one
stan
.
Attach the micro
hone stand
dapter to the dedicated cover
ountin
on a Microphone Stand
sing a Microphone Stand Adapter (OP-R09M; Sold Separately
Using a microphone stand adapter lets
ou mount the R-09HR on a microphone stand (such as the Roland ST-100MB)
A
just t
e ang
e, t
en tig
ten
e retainin
screw.
oosen the retaining screw
opyrig
t © 2008 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION