ENG
ENG
AK68-00029F
DVD PLA
DVD PLA
YER
YER
DVD-C5050
DVD-C5050COVER 12/4/02 3:32 PM Page 1
2
Precautions
Ensure that the mains supply in your house complies whit that indicated on the identification sticker
located at the back of your play. Install your player horizontally, on a suitable base (furniture),
with enough space around it for ventilation (7~10cm). Make sure the ventilation slots are not covered.
Do not stack other, or heavy devices on top over the player. Do not place the player on amplifiers or
other equipmentwhich may become hot. Before moving the player ensure the disc tray empty.
This player is designed for continuous use. Switching off the DVD player to the stand-by mode dose
not disconnect the electricity supply In order to separate the player completely from the mains,it has
to be disconnected by unplugging the main plug, especially when left unused for a long period of time.
1. Setting up
Protect the player from moisture(dripping or splashing and that no objects filled with liquids,such as vases,
shall be placed on the player), and excess heat(e.g.fireplace) or equipment creating strong magnetic
or electric fields (i.e.speakers...) disconnect the power cable from the mains electricity supply if the player
malfunction. Your player is not intended for industrial use but for domestic purposes only. Use of this
product is for personal use only. Condensation If your player or disc have been stored in a cold atmosphsre.
as for example during transportation in the winter, wait for approximately 2 hours until they have reached
room temperature.
2. Caution
Never open the player or any of its components. It can be dangerous for you or certain fragile components.
You could receive an electric shock or touch the laser beam. Do not place your eyes close to the opening of
the disc tray or any other opening to look inside the player.
3. For your safety
Be careful handle your discs with care. Hold a disc whit finger on the border or hole. Always place disc
with the label facing upward (in case of a single side disc ). Always use a soft cloth to clean disc if
necessary, wipe from the centre to the border. Always put disc back into their cases after playing and store
in vertical position. Always place the disc properly into the tray using the proper guide area. Never use
record cleaning sprays, benzine, static electricity liquids or any other solvent, if the disc surface is dirty.
Wipe gently with a soft damp(water only) cloth, never wipe the disc in a circular motion, since circular
scratches are likely to occur and could case noise during playback.
4. Disc
The battery used in this product contains the chemicals that are harmful to the environment.
Do not dispose of batteries in the general household waster. It is recommended that the replacement
of the battery should be done by technician.
5. Battery
For safety reasons, be sure to disconnect the AC power cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for cleaning.
• Wipe the cabinet with a soft cloth.
6. Maintenance of cabinet
DVD-C5050 12/4/02 3:16 PM Page 2
3
Precautions
1
2
3
4
5
D
I
S
C
D
I
S
C
S
K
I
P
E
X
C
H
A
N
G
E
S
T
A
N
D
B
Y
O
N
1
2
3
4
5
DISC
DISC SKIP
EXCHANGE
STANDBY ON
1
2 3
4 5
1
2
3
4
5
DISC
DISC SKIP
EXCHANGE
STANDBY ON
1
2
3
4
5
DISC
DISC SKIP
EXCHANGE
STANDBY ON
1
2
3
4
5
D
I
S
C
D
IS
C
S
K
I
P
E
X
C
H
A
N
G
E
S
T
A
N
D
B
Y
O
N
DVD-C5050 12/4/02 3:16 PM Page 3
Before You Start
Accessories
Install Batteries in the
Remote
If remote doesn’t operate
properly:
1
1
Open the battery cover on the
back of the remote.
2
2
Insert two AA batteries. Make
sure that the polarities (+ and -)
are aligned correctly.
3
3
Replace the battery cover.
• Check the polarity + - of the batteries
(Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by
obstacles.
• Check if there is any fluorescent
lighting nearby.
4
Remote Control
User’s Manual
Batteries for Remote Control
(AA Size)
Video/Audio Cable
DVD-C5050 12/4/02 3:16 PM Page 4
TABLE OF CONTENTS
General Features
............................................................................................................
6
Disc Type and Characteristics ........................................................................................ 7
Description-Front Panel ..................................................................................................8
Description-Rear Panel ....................................................................................................9
Tour of the Remote Control ............................................................................................10
Choosing a Connection ................................................................................................12
Playing a Disc ..............................................................................................................14
Operating the Disc Changer..........................................................................................16
Using the Search & Skip Functions..........................................................................
17
Using the Display Function ............................................................................................18
Repeat Play..................................................................................................................19
Program Play & Random Play........................................................................................20
S.FIT Play ....................................................................................................................21
Digest Play ..................................................................................................................22
Using the Disc View Function ........................................................................................23
Slow Repeat play..........................................................................................................24
Selecting the Audio Language ......................................................................................25
Selecting the Subtitle Language......................................................................................26
Changing the Camera Angle ........................................................................................27
Using the Instant Replay Function ..................................................................................28
Using the Bookmark Function ........................................................................................29
Using the Zoom & 3D Sound Functions............................................................................................30
MP3 Play ....................................................................................................................31
Using the Setup Menu ..................................................................................................33
Setting Up the Language Features..................................................................................34
Setting Up the Parental Control......................................................................................36
Setting Up the Audio Options........................................................................................37
Setting Up the Display Options......................................................................................38
Controlling a TV with the Remote ..................................................................................39
Troubleshooting ............................................................................................................40
Specifications ..............................................................................................................41
5
SETUP
CONNECTIONS
BASIC
FUNCTIONS
ADVANCED
FUNCTIONS
CHANGING
SETUP MENU
REFERENCE
DVD-C5050 12/4/02 3:16 PM Page 5
General Features
DVD Changer
The DVD Changer holds 5 discs and provides
full random play with fast disc changes.
Excellent Sound
Dolby Digital, a technology
developed by Dolby Laboratories provides
crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures
can be viewed.
Slow Motion
An important scene can be viewed in slow
motion.
Programmed Play
You can program tracks to play in desired
order.
Parental Control
The parental control allows users to set the
level necessary to prohibit children from
viewing harmful movies such as those with
violence, adult subject matter, etc.
Various On-Screen Menu Functions
You can select various
languages(Audio/Subtitle) and screen
angles while enjoying movies.
Repeat
You can repeat a song or movie simply by
pressing the REPEAT button.
MP3
This unit can play discs created from MP3
files.
Instant Replay
This function is used to replay the previous
10 seconds of the movie from the current
position.
COPY PROTECTION
• Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player
directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD
discs.
• This product incorporates copyright protection technology that is protected by methods claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
6
* Discs which cannot be played with this player :
• DVD-ROM • DVD-RAM
• CD-ROM • CDV
• CDI
• HD layer of super Audio CD
• CDGs play audio only, not graphics.
* Ability to play back may depend on recording
conditions :
• DVD-R • CD-RW
• DVD+RW, -RW
NOTE
DVD-C5050 12/4/02 3:16 PM Page 6
Disc Type and Characteristics
Disc Markings
Play Region Number
This DVD player is capable of playing the following types of discs with the
corresponding logos:
12Cm
8Cm
Single-sided
240 min.
Double-sided
480 min.
Single-sided
80 min.
Double-sided
160 min.
Audio
+
Video
Audio
+
Video
Audio
• CD is recorded as a
Digital Signal with better
audio quality, less
distortion and less
deterioration of audio
quality over time.
• Video with CD sound, VHS
quality & MPEG-1
compression technology.
• DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
• Various screen and audio
functions can be easily
selected through the on-
screen menu.
VIDEO-CD
AUDIO-CD
12Cm
8Cm
74 min.
20 min.
12Cm
8Cm
74 min.
20 min.
Disc Types
(Logos)
Recording
Types
Disc Size
Max.
Playing Time
Characteristics
DVD
~
DIGITAL
SOUND
STEREO
PAL
• Play
Region
Number
• PAL broadcast
system in U.K,
France,
Germany, etc.
• Dolby
Digital disc
• Stereo disc
• Digital
Audio disc
• DTS disc
• MP3 disc
Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc
to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
7
SETUP
DVD-C5050 12/4/02 3:16 PM Page 7
8
Description-Front Panel
1
2
3
4
5
Front Panel Controls
Front Panel Display
STANDBY/ON
• Use to turn your player on and off (standby).
STANDBY LAMP
• When the unit is first plugged in, the indicator lights.
When power is pressed on, the lamp goes out.
EXCHANGE
• Press this button when you want to change a disc
without stopping playback of the current disc.
DISC SKIP
• Use to skip a disc in order.
HEADPHONES JACK
• You can attach headphones here for private listening.
VOLUME LEVEL
• Use to adjust headphones volume level.
DVD CHANGER(TRAY)
• Press OPEN/CLOSE to open and close the
disc changer.
FRONT DISPLAY
• Operation indicators are displayed here.
PLAY/PAUSE
• Begin or pause disc play.
SKIP/SEARCH
• Use to skip or search a scene or music.
STOP
• Stops disc play.
OPEN/CLOSE
• Press to open and close the disc tray.
DISC SELECT
• Use to select the desired disc loaded in the
DVD CHANGER.
Angle indicator. You can select multiple angles
of a scene recorded by different cameras.
Disc type indicators
Reverse play / Pause / Forward play
Lights when 3D surround is turned on.
DVD : Title number
DVD : Chapter number.
Video/Audio CD : Track number
Repeat play mode
Linear PCM audio output
Dolby Digital Disc
DTS (Digital Theater System) output
MP3 indicator
MPEG-2 Audio output
Displays various messages concerning
operations such as PLAY, STOP, LOAD, ...
no DISC : No disc loaded.
OPEN : The disc tray is open.
LOAD : Player is loading disc information.
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
7.
8.
9.
10.
11.
12.
13.
DVD-C5050 12/4/02 3:16 PM Page 8
SETUP
9
Description-Rear Panel
Rear Panel
S-VIDEO
Y,Pb,Pr
VIDEO OUT
SELECT
DIGITAL AUDIO OUT JACKS
• Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver.
Use to connect to an A/V Amplifier that contains a Dolby Digital or DTS decoder.
ANALOG AUDIO OUT JACKS
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
VIDEO OUT JACKS
• Use a video cable to connect to the Video input jack on your television.
COMPONENT VIDEO OUT JACKS
• Use these jacks if you have a TV with Component Video in jacks. These jacks provide Pr, Pb and Y
video. Along with S-Video, Component Video provides the best picture quality. The Y, Pb, Pr must be
selected in the VIDEO OUT SELECT.
S-VIDEO OUT JACK
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality
picture. The S-Video must be selected in the VIDEO OUT SELECT.
VIDEO OUT SELECT SWITCH
• Use the switch to set video out.
• If Y, Pb or Pr is selected, S-Video will not work.
• If S-Video is selected, Y, Pb or Pr will not work.
NOTE
• Select the VIDEO OUT SELECT switch in the STOP or Power off mode.
1.
2.
3.
4.
5.
6.
DVD-C5050 12/4/02 3:16 PM Page 9
10
Tour of the Remote Control
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DVD-C5050 12/4/02 3:16 PM Page 10
11
SETUP
Tour of the Remote Control
DVD Function Buttons
DVD POWER Button
NUMBER Buttons
STEP Button
• Advances play one frame at a time.
VOLUME Buttons
TV/VIDEO Button
ZOOM Button
S.FIT Button
SEARCH Buttons
• Allows you to search forward/backward
through a disc.
STOP Button
RETURN Button
• Returns to a previous menu.
SETUP Button
• Brings up the DVD player’s Setup menu.
SUBTITLE Button
ANGLE Button
• Use to access various camera angles on a DVD.
MENU Button
• Brings up the Disc menu.
CLEAR Button
• Use to remove menus or status displays from
the screen.
SLOW Button
TV POWER Button
3D Button
OPEN/CLOSE Button
CHANNEL Buttons
DIGEST Button
PLAY/PAUSE Button
• Begin/Pause disc play.
SKIP Buttons
• Use to skip the title, chapter, or track.
BOOKMARK Button
DISPLAY Button
• Displays the current disc mode.
AUDIO Button
• Use this button to access various audio
functions on a disc.
ENTER/DIRECTION Button
(UP/DOWN or LEFT/RIGHT Button)
• This button functions as a toggle switch.
TOP MENU Button
• Takes you to the menu on the DVD disc or
CD/VCD.
REPEAT Button
• Allows you to repeat play a title, chapter,
track, or disc.
MODE Button
• Allows you to program a specific order.
I. REPLAY Button
•
This function is used to replay the previous 10
seconds of the movie from the current position.
DISC SKIP
• Use to skip a disc in order.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
DVD-C5050 12/4/02 3:16 PM Page 11
Choosing a Connection
The following show examples of connections commonly used to connect the DVD player with a
TV and other components.
Before Connecting the DVD Player
Connection to an Audio System
• Always turn off the DVD player, TV, and other components before you
connect or disconnect any cables.
• Refer to the owner’s manual of the additional components you are
connecting for more information on those particular components.
Method 1
Method 2
Analog Audio Out Digital Audio Out
2ch Amplifier
Audio Input Jacks
Dolby Digital Decoder
Digital Audio Input Jack
AUDIO
DVD
OR
12
DVD-C5050 12/4/02 3:16 PM Page 12
Choosing a Connection
Connection to a TV (For Video)
TV (Normal, Widescreen, Projection, etc..)
Good picture
Basic Audio
Better picture
Best picture
Method 1
Method 2
Method 3
Audio Output Jacks
OR OR
AV Cable
S-Video
Cable
Video Cables
Video Output Jack
S-Video Jack
Component Video
Jacks
DVD
TV
• Method 1 DVD Player + TV with Video Input Jack
• Method 2 DVD Player + TV with S-Video Input Jack
(If S-Video is selected in the VIDEO OUT SELECT.)
• Method 3 DVD Player + TV with Component Video Jacks
(If Y, Pb or Pr is selected in the VIDEO OUT SELECT.)
NOTE
• If Y, P
b or Pr is selected, S-Video will not work.
• If S-Video is selected, Y, P
b or Pr will not work.
13
CONNECTIONS
DVD-C5050 12/4/02 3:16 PM Page 13
Playing a Disc
Before Play
Play
• Turn on your TV and press the TV/VIDEO button to select the video mode.
• Turn on your Audio System and select AUX, CD or DVD.
After plugging in the player, the first time you press the DVD POWER
button, this screen comes up :
If you want to select the language, press a NUMBER button.
(This screen will only appear the very first time you plug in the player.)
1
1
Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray opens.
2
2
Place a disc gently into the tray with the disc’s label
facing up.
3
3
Press the PLAY/PAUSE button or OPEN/CLOSE button
to close the disc tray.
4
4
Stopping Play
Press the STOP button during play.
5
5
Removing Disc
Press the OPEN/CLOSE button.
6
6
Pausing Play
Press the PLAY/PAUSE or STEP button on the remote during play.
- Screen stops, no sound.
- To resume again, press PLAY/PAUSE button once again.
14
DVD-C5050 12/4/02 3:16 PM Page 14
Playing a Disc
RESUME function
When you stop disc play, the player remembers where you stopped, so when you press PLAY again, it will pick up
where you left off. (unless the disc is removed, the STOP button is pressed twice or the player is unplugged.)
• If the player is left for 5 minutes in pause mode, it will stop.
• If the player is left in left in the stop mode for more than 30 minutes, the power will autonatically shut off.
(Automatic Power - Off Function)
• If the player is left in the stop mode for more than one minute without any user interaction, a screen saver
will be activated, and the TV screen will fade in and out repeatedly. Press the PLAY button to resume
normal play.
• This icon indicates an invalid button press.
NOTE
7
7
Step Motion Play (Except CD)
Press the STEP button on the remote during play.
- Each time the button is pressed, a new frame will appear.
- No sound is heard during STEP mode.
- Press PLAY/PAUSE to resume normal play.
(You can only perform step motion play in the forward direction.)
8
8
Slow Motion Play (Except CD)
Press the FWD SEARCH or REV SEARCH button on the remote during PAUSE or STEP mode.
- By pressing the FWD SEARCH or REV SEARCH button, you can select slow motion play for
1/8, 1/4 or 1/2 of normal speed.
- No sound is heard during slow mode.
- Press PLAY/PAUSE to resume normal play.
- When playing a VCD, the reverse slow motion play will not work.
15
BASIC
FUNCTIONS
DVD-C5050 12/4/02 3:16 PM Page 15
16
Operating the Disc Changer
The DVD Changer holds 5 discs and provides full random play with fast disc changes.
Exchange allows you to change up to 4 discs except the
disc currently playing.
Exchanging Discs
1
1
Press the EXCHANGE button on the front of the
player when in the play mode. The tray opens
with two slots available for you to load or
change discs.
2
2
Press the DISC SKIP button on the remote or on
the front of the player to turn the platter to the
other two slots. Load or change the third and
fourth discs.
• To change all the discs, first press the STOP button, then the
OPEN/CLOSE and DISC SKIP buttons.
3
3
Press the EXCHANGE, OPEN/CLOSE or the
desired number's DISC SELECT button on the
front of the player to close the disc tray.
Use the Disc Skip function to change to another of the
discs currently in the disc platter.
Using the DISC SKIP function
1
1
While in play or stop mode, press the DISC
SKIP button. The platter turns clockwise to the
next available disc.
2
2
To directly select a disc, press the desired
number of the DISC SELECT buttons on the front
of the unit to play back the disc in the desired
number's slot.
• Empty disc slots are automatically skipped during disc skip.
DISC EXCHANGE
DVD-C5050 12/4/02 3:16 PM Page 16
Using the Search & Skip Functions
During play, you can search quickly through a chapter or track or use the skip
function to jump to the next selection.
Searching through a Chapter or Track
Skipping Tracks
1
1
During play, press the FWD SEARCH (ï) or REV SEARCH (î)
button on the remote.
• Press the REVERSE or FORWARD SEARCH button on the remote and press
again to search at a faster speed on the DVD, VCD, CD.
1
1
During play, press the NEXT SKIP
(ï )
or BACK SKIP
( î)
button.
• When playing a DVD, if you press the NEXT SKIP button, it moves to the
next chapter. If you press the BACK SKIP button, it moves to the
beginning of the chapter.
One more press makes it move to the beginning of the previous chapter.
• When playing a VCD 2.0 in MENU OFF mode, a VCD 1.1 or a CD, if
you press the NEXT SKIP button, it moves to the next track.
If you press the BACK SKIP button, it moves to the beginning of the
track. One more press makes it move to the beginning of the previous
track.
• If a track exceeds 15 minutes when playing a VCD and you press the NEXT
SKIP button, it moves forward 5 minutes.
If you press the BACK SKIP button, it moves backward 5 minutes.
• When playing a VCD 2.0 in the MENU OFF or Track View function,
if you press the NEXT SKIP button, it moves to the next MENU or the
next Track View display.
If you press the BACK SKIP button, it moves to the previous
MENU or the previous Track View display. (See page 23.)
17
DVD
VCD
CD
2X, 4X, 8X, 16X, 32X, 128X
4X, 8X
2X, 4X, 8X
• Depending on the disc, audio may not be heard when a disc is in 2X play mode.
BASIC
FUNCTIONS
DVD-C5050 12/4/02 3:16 PM Page 17
When Playing a DVD
When Playing a CD/VCD
1
1
During play, press the DISPLAY button on
the remote.
- Current title, chapter number, elapsed time, audio,
subtitle and volume control will be displayed.
• Use the NUMBER buttons to enter a different title,
then press the ENTER button.
• Use the LEFT/RIGHT or NUMBER buttons to enter
a chapter number, then press the ENTER button.
• To enter the time from which you want to start,
use the UP/DOWN buttons to select, then use the
NUMBER buttons to enter the time. Then press the
ENTER button.
• Use the LEFT/RIGHT buttons to change the values
of the current audio, subtitle and volume.
• To make the screen disappear, press the DISPLAY
button again.
1
1
During play, press the DISPLAY button on
the remote.
- Current track number, elapsed time and volume
control will be displayed.
• Use the UP/DOWN buttons to select a track.
Use the LEFT/RIGHT buttons or NUMBER buttons
to enter a different track number, then press the
ENTER button.
• To enter the time from which you want to start,
use the UP/DOWN buttons to select, then use the
NUMBER buttons to enter the time.
Press the ENTER button.
• To change the value of the volume, use the
LEFT/RIGHT buttons.
- To make the screen disappear, press the DISPLAY
button again.
*
In VCD 2.0 mode (MENU ON mode), only the
volume control will appear on screen.
A
1-DVD
T : 01
C : 02
0 : 01 : 09
ENG 5.1CH
ENG
64
1-VCD
T : 01
0 : 01 : 09
64
1-CD
T : 01
0 : 01 : 09
64
• What is a Chapter?
Each Title on a DVD is usually divided into
chapters (similar to tracks on an audio CD).
• What is a Title?
A DVD may contain several different titles.
For example, if a disc contains four different
movies, each might be considered a title.
NOTE
VCD
CD
18
Using the Display Function
DVD-C5050 12/4/02 3:16 PM Page 18
Repeat Play
Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.
When playing a DVD
1
1
Press the REPEAT button on the remote. Repeat
screen appears.
2
2
Select Chapter, Title or A-B using the
LEFT/RIGHT buttons.
- Repeat A-B
• Press the REPEAT button. Select A-B on screen with the
LEFT/RIGHT buttons or press the A-B button on the remote.
• Press ENTER at the point where you want the repeat play
to start (A). The B is automatically highlighted.
• Press ENTER at the point where you want the repeat play
to stop (B).
3
3
Press ENTER.
4
4
To return to normal play, press REPEAT again,
then press the LEFT/RIGHT buttons to select Off
and press ENTER.
NOTE
• DVD repeats play by chapter or title, CD and VCD repeat play by disc or track.
See page 31 to MP3 disc repeat play.
• Depending on the disc, the Repeat function may not work.
• If the title or track is completed before marking the end (B), the end of title or track becomes B automatically.
• When in VCD 2.0 mode (MENU ON mode), this function does not work.
DVD
VCD/CD
19
BASIC
FUNCTIONS
DVD-C5050 12/4/02 3:16 PM Page 19
20
Program Play & Random Play
PROGRAM RANDOM
NOTE
• Depending on the disc, the Program and Random Play function may not work.
• When in VCD 2.0 mode (MENU ON mode), these functions do not work.
• To resume normal play, press the CLEAR button.
• Random Play can only operate when the discs are the same type.
Program Play (DVD/VCD/CD)
Random Play (DVD/VCD/CD)
1
1
Press the MODE button.
2
2
Use the LEFT/RIGHT buttons to select
PROGRAM. Press the ENTER button.
All discs in the unit will be read first.
3
3
Use the LEFT/RIGHT buttons to select the first
chapter (or track) to add to the program. Press
the ENTER button. The selection numbers appear
in the Program Order box.
4
4
Press the PLAY/PAUSE button. The disc will be
played in programmed order.
• Use the DISC SKIP key to program another disc.
1
1
Press the MODE button.
2
2
Use the LEFT/RIGHT buttons to select RANDOM.
Press the ENTER button.
3
3
Press Left/Right buttons to select All discs or Disc.
The disc(s) will be played in random order.
Chap. (T:01)
Program order
(ALL)
02 03 04
05 06 07 08
DISC
2. --- 3.CD 4. --- 5.VCD
01
RETURN CLEAR ENTER PLAY
PROGRAM 01
1.DVD
RETURN CLEAR ENTER PLAY
PROGRAM 02
Chap. (T:01)
Program order
(ALL)
03
1.02
04
05 06 07 08
DISC
01 02
1.DVD 2. --- 3.CD 4. --- 5.VCD
DVD-C5050 12/4/02 3:16 PM Page 20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/