Maytronics Dolphin X40 Plus Quick start guide
- Category
- Robotic vacuum cleaners
- Type
- Quick start guide
Your robot has a Weekly Timer feature that enables
you to set an automatic cleaning schedule for
the week ahead.
When the power supply is switched on, you can press the
Weekly Timer button to select one of the following cleaning
schedule options for the week ahead:
Dolphin Power Supply
Advanced Operation
(Dolphin X40+):
1. You can program the power supply at any time.
See the relevant section below for more details on each program.
2. If no program is selected, the robot will perform a single cleaning
cycle.
Weekly Timer
The robot will automatically work every day for a full cycle,
The robot will automatically work every alternate day for a full cycle,
The robot will automatically work every 3 days,
When the LED under the Full Cycle icon is lit: The robot will work in the regular manner.
When the LED under the Fast mode icon is lit: The robot will work in fast mode.
In this mode, the cycle duration is one hour and the robot cleans the pool floor only.
Note: Once Fast Mode is selected, the robot will continue to work in Fast Mode every time. To revert
to the standard cleaning method, press the button. The LED under the Full Cycle icon will light up.
After selecting one of the above options, the robot will start to operate at the next occurrence
of the programmed start time.
Note: A fourth click will cancel the cleaning schedule program (without a visible indication).
If the robot is working in Weekly Timer mode, the Weekly Timer button constantly blinks between cycles.
At the end of the week, the power supply automatically switches off and you need to reschedule the robot.
Regular/Fast Mode
Your robot has a Fast Mode feature that enables you to select
a fast cleaning cycle instead of a standard cleaning cycle.
that is, once a day for 7 days.
that is, 4 times in a week.
that is, 3 times in a week.
Three clicks
Two clicks
One click
R
Bluetooth Connection
Weekly Timer
Smartphone Control
Fast Mode
Delayed Operation
ON/OFF
Note: If you are programming the robot using a smartphone, it cannot be
manually programmed using the Power supply.
dolphinpoolrobot.com/mydolphin-app-ios dolphinpoolrobot.com/mydolphin-app-android
8151470
Download the app
Delayed Operation
Your robot has a Delay feature that enables you to delay the cleaning
start time. This delay allows the dirt to settle at the bottom of the pool.
When the Power supply is switched on, you can press the Delayed Operation
to delay the cleaning start time.
When the LED under the Delayed Operation icon is lit:
The robot will automatically start working after a two-hour delay.
During that time, the ON button continuously blinks, waiting to start.
Once started, the ON button blinks continuously until the robot starts working.
This is a one-time operation. Delayed Operation needs to be activated each time it is required.
Bluetooth Connection
Your robot has a Bluetooth® Connection indicator. When the LED indicator is on,
it indicates that the smartphone paired with the robot is identified nearby.
This only works if the phone’s Bluetooth® is activated.
Refer to the Smartphone Control section for more information about smartphone connectivity.
Smartphone Control
The Smartphone Control feature is available with the Dolphin X40+
To activate it, download and activate the MyDolphin™ application.
R
Download full user manual
www.maytronics.com.au/99996214-PW
Quick start guide
• Unplug the power supply before servicing.
• Do not pull the Pool cleaner from the pool
using the cable.
• Use the Pool Cleaner in the following water
conditions only: Chlorine Max 4 ppm;
pH 7.0 - 7.8; Temperature 6 -34°C (43-93°F);
NaCI Maximum = 5000 ppm.
•
Specifications:
Motor protection: IP 68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologies,
long lasting performance and easy maintenance. You and your family will be free to
enjoy swimming with full confidence that your pool is completely clean.
• Use the originally supplied power supply only.
• Do not use an extension cable in any case
whatsoever.
• Ensure the electrical outlet is protected by
a ground fault interrupter (GFI) or an earth
leakage interrupter.
• Keep the power supply out of standing water.
• Do not enter the pool while the Pool Cleaner
is working.
• When working, the Power Supply should be
placed in the shade.
• If the pool robot is fitted with combined or
wonder brushes, gently aqueeze the brushes
until they are soaked with water.
• Release minimal required floating cable
length to ensure proper pool coverage. Leave
excess cable rolled outside the pool.
Dolphin X40 PLUS
Thank you for purchasing a Maytronics Robotic Pool Cleaner.
• After each cleaning cycle wash the filter bag or
cartridge. Clogged filter bags reduce scanning
and cleaning efficiency.
• Once a week unplug the cable from the power
supply, unwind the tangled portions of the
cable, straighten it out and leave it in the sun
for several houres.
• Store the pool cleaner in a shady place on
its Caddy, if not on a caddy, place the pool
cleaner upside down.
Cautions & Warnings
Helpful hints
Caddy Assembly
DIN 127B A2 M5 x 2
2
3
5
7
2
4
4
DIN 1587 A2 M5
x 2
3
WN 1412 A2 KA50X16
x 6
4
DIN 7985 A2 M5X35
x 2
1
4a
4b
A
B
A
B
3
2
3
2
1
1
1
2
3
3
2
1
6
8
1
9
B
A
8mm (
5
/
16
”)
4
4
4
4
4
Download full user manual
www.maytronics.com.au/99996214-PW
Attach the floating cable to the power supply.
Robot operation
Maintenance
Set Up
Into the pool
Operation
Out of the pool
Storage
Periodic filter cleaning
Cleaning the impeller
Cleaning the filter
away from the edge of the pool.
Position the power supply at least 3m/10ft
Turn the power supply ON.
The Pool Cleaner will now
operate until it has reached
the end of the cleaning cycle.
It is highly reccomended to clean the filter basket after each cleaning cycle.
Note: Don’t let the filter cartridges dry out before cleaning.
Unplug the power supply before servicing
Clean the debris trapped in the impeller opening,
according to the following steps:
Lift up the basket.
Open the latch to
release the bottom
lid in order to remove
the debris.
Clean the filter basket
with a hose.
Open the filter cover.
If you notice debris trapped in the impeller:
Coil the cable and store in a cool, dry place on the Caddy.
Do NOT store the robot where it will be exposed to direct sunlight, excessive heat or to frost.
Unplug the power supply before servicing
Put the Pool
Cleaner into the
pool.
Release the Pool
Cleaner and let it
sink to the floor
of the pool.
Make sure that the
floating cable is
free of any
obstructions.
6
Dismantle the 4 ultra-fine filter panels of the outer basket according to the following steps:
Holding down the handle
remove the inner net basket.
Dismantle the panels,
starting with pressing on
panel no.1 using your
thumbs.
Continue to dismantle the panels in the
order of their nombers: no.2--> no.3-->
no. 4.
1
2
1
2
4
5
1
2
3
1
2
ON
6a
2
1
3
1
3
2
3
5
2
7
1
4
6b
6c
6d
Cable Tip:
Unwind the
cable &
stretch it out
poolside so
that it has
no kinks
-
1
-
2
-
3
-
4
Maytronics Dolphin X40 Plus Quick start guide
- Category
- Robotic vacuum cleaners
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Maytronics Dolphin Wave 50 User manual
-
-
Maytronics 8152200 User manual
-
Maytronics Dolphin Wave 30 User manual
-
-
-
-
Maytronics 9999096X-USW User manual
-
-
Other documents
-
Dolphin 8151790 User manual
-
ROBOTIC Basic 4-UNI User Instructions
-
Dolphin Supreme M4 User Instructions
-
Dolphin 8151810 4-UNI Operating instructions
-
-
-
Dolphin S200 User manual
-
FLOTIDE XR2 Robotic Swimming Pool Cleaner User manual
-
Interline Robotic Pool Cleaner User guide
-
Zodiac LAZERNAUT User manual
