Kathrein UFC 965si Operating instructions

Operating manual UFC 965

English

Receiver Order no. Operating manual valid as of software version:

UFC 965si 20210187

1.00

UFC 965sw 20210186

HDTV Cable Receive

r

2

Dear customer,

this operating manual is intended to help you make the fullest use of the extensive range of functions offered

by your new receiver.

We have tried to make the operating instructions as easy as possible to understand, and to keep them as

concise as possible. To help you understand particular specialist terms that cannot be translated, we have

added a short glossary at the end of the manual.

The power switch is an environmentally friendly feature. If you will not be using your receiver for an extended

period, you should use the on/off switch to disconnect it from the power supply and save energy. For shorter

breaks, you can use the remote control to switch the receiver to standby, which uses only a minimal amount

of energy.

We hope your reception will always be brilliant and you will enjoy using your new HDTV receiver.

Your

KATHREIN team

Preface

3

Information on Audio MPEG Inc. and S.I.SV.EL, S.P.A:

This unit makes use of legally protected technologies, which are protected by patents in the USA and also

by other intellectual property rights in other countries.

KATHREIN-Werke KG has obtained licences from Audio MPEG Inc. and Societa‘ Italiana per lo sviluppo

dell‘elettronica, S.I.SV.EL, S.P.A to use these technologies. These licences carry certain restrictions, which

apply also to you as the customer. Accordingly this unit may only be used by the end customer for private

non-commercial purposes and for the licensed content. It may not be used for commercial purposes. The

use of products or processes that are sold or used with this unit is not included in this statement. The use of

reverse engineering is not permitted in respect of the licensed technologies, nor is disassembly.

Legal Information

Manufactured under licence from Dolby Laboratories. "Dolby" and the double-D

symbol are registered trademarks of Dolby Laboratories.

The terms HDMI and HDMI High-Deﬁ nition Multimedia Interface, and the HDMI

logo are trademarks or registered trademarks of HDMI Licensing LLC in the USA

and other countries.

®

Software changes/use of applications

Any modiﬁ cations to the receiver software, or the use of applications not provided by Kathrein will invalidate

the warranty! You will have to bear the costs yourself for shipping and repairing any receiver that requires

attention due to modiﬁ cations to the software and use of applications other than those provided by Kathrein!

Therefore use only software and applications provided by Kathrein for your receiver. These are available for

download from our website (www.kathrein.de).

Kathrein assumes no liability for the loss of recordings/data on internal hard disks or external storage media.

The software installed on the device/product before dispatch from the factory is suitable for its function and

is of the quality usual for this type of software. It has not been technically possible to fully eliminate all bugs

during the software development process. However the software as delivered is defective only if it fails to

perform the functions usual for the device/product. A shortcoming that causes only an insigniﬁ cant reduction

in quality does not rank as a defect. Functional shortcomings in the software or program that result from

hardware defects, ambient conditions, incorrect operation or the like do not rank as software defects.

CI+ and the CI+ logo are trade marks or registered trade marks of CI Plus LLP.

The UFC 965 satisﬁ es the minimum requirements of CI+.

Note on Macrovision:

The product is equipped with copyright technology, which is protected by patents in the USA and by other

intellectual rights of the Rovi Corporation. Use of reverse engineering or disassembly is prohibited.

4

List of Contents

Preface............................................................... 2

Legal Information ............................................. 3

List of Contents ................................................ 4

Safety Instructions - Important Notes ............ 6

Receiver Features/Scope of Supply ............. 10

Receiver features ........................................... 10

Scope of supply .............................................. 10

Features........................................................... 11

Special features ............................................. 11

Further features .............................................. 11

Connections ................................................... 11

Connection and Set-Up .................................. 12

Front/rear view of the receiver

(front flap open) .............................................. 12

Inserting batteries into the remote control ...... 13

Connecting the receiver ................................. 14

TV connection ................................................ 14

Audio connection ............................................ 15

Digital .................................................................... 15

Analogue ............................................................... 15

Connecting up the video/DVD recorder ......... 15

First installation .............................................. 16

Basic Functions .............................................. 19

Remote control in live mode (TV/radio) .......... 20

I want to watch TV ... ...................................... 21

I want to listen to the radio ... ......................... 22

I want to access teletext ... ............................. 23

I want to watch time-shift TV ... ...................... 24

I want to record a programme immediately ... 25

I want to record a programme that is

scheduled for later (timer list) ........................ 26

I want to play back a recording ... .................. 27

I want to delete a recording ... ........................ 28

Alphanumeric entries ..................................... 29

Switching between TV and radio operation .... 30

Adjusting the volume ...................................... 30

Channel selection ........................................... 30

... direct .................................................................. 30

... from channel list ................................................ 30

Channel banners (information) ....................... 32

Audio selection ............................................... 34

Subtitle selection ............................................ 34

Teletext ........................................................... 35

One Touch Recording (OTR) -

recording direct to hard disk ........................... 36

Picture-in-picture ............................................ 37

Electronic Programme Guide (EPG) ............. 38

General information on the programme

guide .............................................................. 38

Calling up the EPG ......................................... 39

Navigation (remote control buttons

in the EPG) ..................................................... 40

EPG views ...................................................... 41

"Current" view ........................................................ 41

"Preview" view (channel guide) ............................. 42

Recording list view ................................................ 43

Timer recording .............................................. 43

Programme present in the EPG ............................ 44

Programme not present in the EPG ...................... 44

Specifying a recording mode ................................. 45

Recording (Timer) list view .................................... 47

Editing a scheduled recording ............................... 47

Timer overlap ......................................................... 48

Search function .............................................. 49

Recording Archive

(Playing Back/Editing Recordings) ............... 50

Calling up the recording archive

(My recordings) .............................................. 50

Navigation (remote control buttons

in the recording archive) ................................. 51

Recording archive views

(sorting the recordings) .................................. 52

Playing back a recording ................................ 53

Editing recordings .......................................... 56

Delete .................................................................... 57

Rename ................................................................. 57

Selecting several recordings ................................. 58

Folders in the recording archive ..................... 59

Create new folder ... .............................................. 59

Editing folders (rename/delete) ............................. 60

5

List of Contents

Main Menu ....................................................... 61

Calling up the main menu and introduction .... 61

Overview of the main menu submenus .......... 62

Main Menu - Installation ................................. 63

Calling up the menu ....................................... 63

Auto Scanning ................................................ 63

Manual Scanning ........................................... 64

Blind Scanning ............................................... 65

Defaults Setting .............................................. 66

Main Menu - System Setup ............................ 67

Calling up the menu ....................................... 67

Language Setting ........................................... 67

Language selection and country setting ......... 68

OSD Setting ................................................... 68

Video Setting .................................................. 69

Audio Setting .................................................. 70

Time Setting ................................................... 71

Other Setting .................................................. 72

System Information ........................................ 73

Main Menu - Channel Setup ........................... 74

Calling up the menu ....................................... 74

Delete Channels ............................................. 74

Delete All Channels ........................................ 75

Favourite Channels ........................................ 75

Edit Channels ................................................. 76

Main Menu - Parental Lock ............................ 78

Calling up the menu ....................................... 78

Channel Lock ................................................. 78

Lock Control ................................................... 79

Change PIN Code .......................................... 80

Main Menu - Software Manager ..................... 81

Calling up the menu ....................................... 81

System Recovery ........................................... 81

Main Menu - Multimedia ................................. 82

Calling up the menu ....................................... 82

Reservation Setting ........................................ 82

PVR Setting (optional) .................................... 84

Player Setting ................................................. 84

Storage ........................................................... 85

Software update ............................................. 86

Game ............................................................. 87

Main Menu - Conditional Access .................. 88

Calling up the menu ....................................... 88

Operation from the Front Panel

(without remote control) ................................ 90

Backup operation ........................................... 90

Technical Appendix ........................................ 91

Technical data ................................................ 91

Brief Technical Glossary ................................ 93

Troubleshooting ............................................. 95

Service ........................................................... 95

6

Safety Instructions - Important Notes

Mains power cable

Make sure that the mains cable

(power supply cable) is not damaged.

Units with a damaged mains cable

must be disconnected from the mains

(unplug it at the socket) and repaired

by an electrical specialist before being

used. Only use the power supply unit

supplied (if available)!

Risk of fatal injury due to electric

shock!

Danger!

Cleaning

Disconnect the mains plug before

cleaning the unit. Use a dry cloth for

cleaning and only clean the outer

surface. Never open the casing of the

unit.

Touching the parts inside the unit

carries a risk of death due to electric

shock!

Playing children

Make sure that children do not push

any objects into the ventilation slots.

Risk of fatal injury due to electric

shock!

Earthing

The antenna system must be earthed

or equipotentially bonded as speciﬁ ed.

EN 60728/11 and any national

regulations must be complied with.

Risk of voltage surges due to lightning

strikes!

Power supply voltage

Operate the unit at the speciﬁ ed

mains voltage only (indicated on the

rear of the receiver or on the external

power supply unit). The unit may only

be connected to the mains and turned

on once it has been connected to the

antenna and to the TV set or the cable

network and PC.

If the mains voltage is too high, there

is a risk of ﬁ re!

Moisture, direct sunlight, heat,

naked ﬂ ames

Protect the unit against moisture,

dripping and splashed water (do not

place any ﬁ lled objects such as vases

on top of the unit). Do not place the

unit close to a heater or expose it to

direct sunlight and do not operate it

in damp locations. Only use the unit

in a moderate climate, not in tropical

conditions! Do not place naked ﬂ ames

such as candles on top of the unit!

There is a risk of ﬁ re!

Ventilation

The heat generated in this unit is

adequately dissipated. However,

the unit should never be installed

in a cupboard or on shelves with

inadequate ventilation. Never cover

the cooling slots on the unit (e.g.

with other equipment, magazines,

tablecloths, clothing or curtains)!

Batteries

If your unit was supplied with batteries

(e.g. for the remote control), take care

that the batteries are not exposed

to excessively high temperatures,

direct sunlight or ﬁ re. Replace the

batteries only with types that are

identical or equivalent, otherwise the

batteries or the remote control may be

damaged. Also comply with the safety

instructions stated on the batteries:

There is a risk of explosions!

Warning!

These two pages contain important information about the operation, installation location and connection of

the unit. Read these instructions carefully before setting up the device.

Do not

cover

7

Safety Instructions - Important Notes

Periods of extended absence,

thunderstorms, mains socket

accessibility

In order to disconnect the unit from

the mains completely, the mains plug

must be unplugged from the mains

power socket! Therefore install the

unit close to a mains socket and make

sure this socket is accessible at all

times, so that you can disconnect the

unit from the mains if necessary.

If you are away for an extended

period, and during thunderstorms,

always switch the unit off at the mains

and unplug the power plug from the

socket. This also applies to the other

equipment connected to the unit.

Isolation from the cable network is

also recommended. Note any timer

programming (receiver) and turn the

unit on again promptly before the

recording time.

Installation location

All electronic equipment generates

heat. The temperature rise of this unit

does however lie within the permissible

range. Sensitive furniture surfaces and

veneers may become discoloured by

the effects of constant heat over time.

The feet of the unit can also cause

colour changes to treated furniture

surfaces. If necessary, place the unit

on a suitable stable and ﬂ at base!

Repairs

Ensure that any repairs to your unit

are carried out by qualiﬁ ed personnel.

Opening the unit and attempting to

repair it yourself will void all warranty

claims!

Improper work on the unit may

jeopardise the electrical safety of the

unit.

The manufacturer accepts no liability

for accidents caused by the user

opening the unit casing!

Connections

Incorrect wiring of the connections

can lead to malfunctions or defects on

the unit!

Important!

Do not place any objects on top of

the unit. Unless stated to the contrary

in the "Connection and set-up" and

"Installation" sections in the manual

supplied, maintain a clearance of at

least 10 cm above the unit, 2 cm to

either side and 5 cm behind the unit,

to allow unobstructed dissipation of

the heat generated.

There is a risk of ﬁ re!

Electronic equipment is not domestic

waste - it must be disposed of

properly in accordance with directive

2002/96/EC OF THE EUROPEAN

PARLIAMENT AND THE COUNCIL

dated 27

th

January 2003 concerning

used electrical and electronic

appliances.

At the end of its service life, take

this device to a designated public

collection point for disposal.

Used batteries are special waste!

Do not throw used batteries into

your domestic waste; take them to a

collection point for used batteries!

8

Product return/original packaging

Make sure that the ventilation slots on the unit are not blocked or covered in any way.

otherwise the unit may overheat.

There is a risk of ﬁ re!

You must not disconnect the receiver from the mains while it is in operation!

This can lead to a loss of data and corruption of the software.

Safety Instructions - Important Notes

Please keep the original packaging in case you need to return the product at any time. The receivers are

fragile due to their construction and are only adequately protected by the original packaging. If the receiver

is not shipped correctly the guarantee/warranty on it will be rendered void.

Before you disconnect the receiver from the mains, you must switch it to the standby mode by pressing the

standby button (on/off) on the remote control. In standby mode, any changed or new data that are broadcast

will be saved by the receiver. As soon as the receiver is in the standby mode, it can be disconnected from

the mains at any time.

Ventilation slots on the unit

Switching the receiver off

Warning!

Channel assignment

The channels available on the cable network are subject to continual change. When such changes occur

it is necessary to reset the channels. The information for these settings can be found on the Internet or in

relevant magazines.

Updating the receiver software

Your receiver was equipped in the factory with the latest software version available at that time. We are,

however, constantly working on adapting the software to the wishes of our customers and to developments

in technology. Further information on this can be found in the sections "Main Menu - Multimedia", "Software

update".

9

The information in this operating manual was correct at the time of going to print. We reserve the right

however to make changes at any time and without prior notice. If new software is released for your

receiver, and this affects the information in the operating instructions (e.g. changes to the menus and/or

functions), if we believe it necessary we will make available new operating instructions for download at

"www.kathrein.de".

Make a note of the receiver's basic settings (these are set during ﬁ rst installation), so you can restore them

if necessary!

Please be aware of your responsibility towards your fellow human beings. Keep this manual

for any questions that arise later, and if the receiver passes to another owner, pass it on to the

new owner.

For compliance with the EMC Directives, the USB connection cable between the receiver and hard disk

must not be longer than 50 cm.

Miscellaneous

Safety Instructions - Important Notes

10

Receiver Features/Scope of Supply

■ UFC 965

■ Remote control

■ HDMI cable

■ 2 Batteries AAA 1.5 V

■ Operating manual

■ Safety instructions (multi-lingual)

The UFC 965/CI+ HDTV receiver is suitable for the reception of digital cable TV and radio channels. The

receiver can be used to receive both high resolution and also conventional TV. In addition a CI+ interface

for a CI+/CI module is ﬁ tted, for decoding Pay-TV channels. Via the optical audio output, the receiver

can output the Dolby

*)

Digital data stream (AC 3) to a Dolby Digital system. The integrated EPG is not

only a clearly laid out electronic TV guide, but also enables programmes to be copied directly from the

related EPG view to the timer. The USB port on the unit's rear panel permits the connection of external

storage media (USB stick/hard disk) for recording TV and radio broadcasts. The receiver is available

in a silver or black casing.

*)

Dolby is a registered trademark of Dolby Laboratories

Receiver features

Scope of supply

11

Features

Special features

Further features

Connections

1)

CI+/CI modules are not included with this product

2)

Only with hard disks from the Kathrein product range or with suitable hard disks (www.kathrein.de)

3)

In accordance with NorDig speciﬁ cation Desc. 1.0, must be supported by the network operator

Technical data subject to change.



Guided ﬁ rst installation with country

setting



Common Interface for one CI+/CI module

1)



Recording of TV and radio broadcasts on

an external USB hard disk

2)



Timeshifting using external USB hard

disk

2)



EPG with intuitive timer programming



Compatible with the UFO

®

compact signal

processing system



Automatic channel list sorting

3)



Reception of digital cable TV and radio

channels



Video decoding of MPEG-2 and

MPEG-4/H.264 signals (HDTV)



Up-scaler for scaling up the PAL signal

to 1080p



Nine favourite channel lists



Language selection for multilingual

broadcasts



On screen display (OSD) in more than

20 languages



5,000 channel memory positions



Videotext decoder with 800 page memory

capacity



4-character display



Power switch



Standby: 0.5 W



2 x IEC connector (f)/(m) (1 x input,

1 x output)



1 x USB 2.0 (rear panel)



1 x CI+/CI slot



1 x HDMI out



1 x YPbPr component output



1 x Analogue video (composite colour) -

Cinch



2 x Analogue audio (l/r) - Cinch



1 x Digital audio (S/PDIF optical)



1 x Power connection 230 V/50 Hz

12

HDMI = High-Deﬁ nition Multimedia Interface (digital interface for video and audio)

Front/rear view of the receiver (front ﬂ ap open)

Connection and Set-Up

*

)

CA modules and smart cards are not included

with this product

**

)

Pressing the Off switch does not full

disconnect the unit from the mains (see the

sections "Safety Instructions - Important

Notes" and "Periods of extended absence,

thunderstorms, mains socket accessibility")

Rear view:

1. Aerial output (loop-through socket)

2. Input socket for digital cable connection

3. 3 x Cinch connections for component outputs

labelled = Y/Pb/Pr

4. Scart socket for TV connection

5. Optical digital data stream output

6. Audio outputs (R/L) cinch sockets

7. Video output (CVBS)

8. USB 2.0 port (USB-A connector)

9. HDMI connection

10. Mains power cable

11. Power switch **

)

Front view (ﬂ ap open):

1. On/Off button (operation/standby)

2. Channel selection button down

3. Channel selection button up

4. 4-digit LED display

5. Common Interface for ﬁ tting one CI/CI+

module for Pay-TV cards *

)

1 2 3

4

OPTICAL

TV

RL

RF

INPUT

Y

Pb

Pr

47-862MHz

5V

0,5A max.

USB 2.0

Manufactured under license from

Dolby Laboratories. Dolby and the

double-D symbol are trademarks

of Dolby Laboratories.

LOOP

OUT

VIDEO

OFF

ON

90-240V~

50/60Hz

18W

1 2 3 4 5

6 7 8 9

10

11

5

13

Connection and Set-Up

Remove the cover on the rear of the remote control. Insert the two batteries supplied into the remote

control. Ensure correct polarity of the batteries; the + and – markings are indicated inside the battery

compartment. Slide the cover back onto the housing until it locks in place.

Inserting batteries into the remote control

To open:

Gently press here and pull

backwards

14

HDMI

Scart

TV

OPTICAL

TV

RL

RF

INPUT

Y

Pb

Pr

47-862MHz

5V

0,5A max.

USB 2.0

Manufactured under license from

Dolby Laboratories. Dolby and the

double-D symbol are trademarks

of Dolby Laboratories.

LOOP

OUT

VIDEO

OFF

ON

90-240V~

50/60Hz

18W

Connect the receiver (HDMI or alternatively TV Scart socket) to the TV set using an HDMI or Scart cable

(see the connection example above).

Connecting the receiver

TV connection

Connection and Set-Up

Connect the RF IN input of the receiver to the antenna socket. Use a coaxial cable with

a standard IEC connector.

If the IEC connector is not yet ﬁ tted to the cable, strip the insulation from the cable

as shown in the following illustration and carefully ﬁ t the connector to the end of the

cable so that it is securely ﬁ tted.

When ﬁ tting the connector, make sure that no strands of the braid are touching the

inner conductor, otherwise a short circuit will occur.

The quality of the reception signal depends on a good connection at this point!

Screw on

Turn back

Slit open longitudinally (3x)

15

There are two ways you can access the digital audio.

HDMI

The stereo audio is transmitted to your TV set via the HDMI interface. If your TV set also supports

Dolby Digital, you can also receive the Dolby Digital audio via the HDMI interface (providing it is

broadcast by the channel provider). On this issue refer to the operating instructions for your TV set.

SPDIF Dolby Digital output (optical)

The SPDIF output is intended for the connection of a Dolby Digital system (see "Advanced connection

example" in the technical appendix). Connect the SPDIF output and the Dolby Digital system using an

appropriate cable.

If you want to play the sound on your hi-ﬁ system, connect the audio cinch sockets to the input sockets

on the hi-ﬁ system, using an appropriate cable (see "Advanced connection example" in the technical

appendix).

Connect the receiver (TV Scart socket) to the video recorder/PVR using a Scart cable (necessary only if

the TV set and receiver are not already connected using a Scart cable).

For system reasons, the same video signals are present at both the TV Scart socket and also the video

cinch output.

Audio connection

Digital

Analogue

If you are recording to an external video recorder/DVD, remember not to operate the receiver

during recording, otherwise all the on-screen displays will appear on your recording.

During recording with a video/DVD recorder, no channel may be viewed other than the one being

recorded. Only if the recording is on to a USB hard disk can any other channel be viewed.

If the receiver is started by means of a timer recording, there will be no picture on your TV set.

Only when the standby button (On/Off) is pressed will a TV picture be visible or the receiver begin

operation.

Connection and Set-Up

Connecting up the video/DVD recorder

SPDIF = Sony Philips Digital Interface Format (digital output for Dolby Digital AC 3 audio)

Tip!

16

Before you start to use the UFC 965, read the sections "Safety Instructions

- "Important Notes" and "Connection and Set-Up" through to the item "First

installation".

Do not connect the unit to the mains until all installation work has been properly

carried out.

The guidance provided in the "First installation" section assumes that the receiver has been

properly connected as per the "Safety Instructions - Important Notes" and "Connection and

Set-Up" chapters through to the "First installation" section.

Required buttons on remote control for ﬁ rst installation:



...



Number input



(blue)

Proceed to the next step in the

ﬁ rst installation



(red)

Go back one step in the

ﬁ rst installation



Conﬁ rm the changed

values/setting;

call up the submenus



Select/change individual

menu parameters, navigation



Cancel entry, go back

First switch your TV set on and select the AV-/HDMI input you have used to connect the receiver to your

TV set. Switch on the receiver at the power switch on the rear of the unit. Now perform the ﬁ rst installation.

If you have any questions or encounter problems, contact your specialist dealer.

The following on-screen display appears:

Always check the bar at the bottom of

the on-screen display. This provides

information on what to do next.

Use the



buttons to select the desired menu language and conﬁ rm your selection using the



button. The following languages are available: English, German, Turkish, Russian, French, Arabic,

Italian, Portuguese, Spanish, Polish, Czech, Swedish, Norwegian, Finnish, Greek, Serbian, Hungarian,

Croatian, Danish, Dutch and Albanian.

First installation

Connection and Set-Up

Tip!

17

The following on-screen display appears:

Connection and Set-Up

Use the



buttons to select the country in which the receiver is to be operated and press the



button to conﬁ rm your selection. The following countries are available: England, Germany, Turkey,

Russia, France, Italy, Portugal, Spain, Poland, Czech, Sweden, Norway, Finland, Greece, Serbia,

Hungary and Switzerland.

The following on-screen display appears:

Select the line you want to change using the



buttons. Make the settings using the



buttons.

Daylight Saving:

Select the currently applicable setting (daylight saving either "On" or "Off" for winter).

Time Zone:

Select your time zone here (e. g. for Germany select "Berlin, Rome").

Local Time:

Is generated automatically from the cable signal

Press the



button.

18

Connection and Set-Up

The following on-screen display appears:

The receiver automatically starts a channel search. The channel search may take a few minutes. The

following on-screen display then appears (example):

Press the



button. First installation is then complete. The receiver automatically shows the TV picture

for the ﬁ rst channel.

19

Basic Functions

Following an overview of the remote control, a simple explanation will be provided of the receiver’s

most important functions (with all the required buttons on the remote control). The explanations in the

sections "I would like to ..." merely demonstrate the most simple use of the relevant receiver functions

without going into any great detail.

For more detailed explanations of the functions, refer to the relevant sections.

20

Basic Functions

Remote control in live mode (TV/radio)



(red) = Call up favourites list



(green) = Picture-

in-picture function

Volume "-" (softer)

Volume "+" (louder)

Call up teletext and subtitles

Operation (on)/standby (off)

Overview of the button functions

on some menus

Number pad

Call up main menu

Mute

Channel selection

Call up channel information (info

banner and detailed information)



(yellow) = Call up other

settings (Options menu)



(blue) = Switch between

TV/radio mode

Call up EPG (Electronic

Programme Guide)

Call up recording archive



= Navigation/channelor

options, channel change



= Call up channel list,

conﬁ rmation/call up selection

Call up recording list



= Pause/start time-shift



= Start recording (OTR)



= Stop playback/

Time-shift/Record



= Fast rewind



= Start playback



= Fast forward

Leave on-screen displays/

menus in steps

OTR = One Touch Recording

Time-shift TV

Page is loading ...

Kathrein UFC 965si Operating instructions

This manual is also suitable for

Kathrein UFC 965si Operating instructions

Related papers

Other documents