Sony MHC-V909AV Operating instructions

SONY MHC-V909AV (E) 3-860-316-11(1)Actual page number:

Mini Hi-Fi

Component

System

3-860-316-11(1)

MHC-V909AV

Operating Instructions

01/00-01_MHC-V909AV.11E 98.11.9, 11:44 AM1

2

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Laser component in this product is capable of

emitting radiation exceeding the limit for Class 1.

This caution label is located inside the unit.

This appliance is classified

as a CLASS 1 LASER

product. The CLASS 1

LASER PRODUCT

MARKING is located on

the rear exterior.

This system can play

the following discs:

VIDEO CDs Audio CDs

Disc logo

Contents Audio + Video Audio

(moving pictures)

Disc size 12 cm/8 cm 12 cm/8 cm

Play time 74 min./20 min. 74 min./20 min.

Note on VIDEO CDs

This system conforms to VIDEO CDs without PBC*

functions (Ver. 1.1) and VIDEO CDs with PBC*

functions (Ver. 2.0) of VIDEO CD standards. You

can enjoy two kinds of playback according to the

disc type.

Disc type You can

VIDEO CDs without Enjoy video playback

PBC functions (moving pictures) as

(Ver. 1.1 discs) well as audio CDs.

VIDEO CDs with Play interactive

PBC functions software using menu

(Ver. 2.0 discs) screens displayed on

the TV screen (menu

playback), in addition

to the video playback

function of VIDEO

CDs without PBC

functions.

Moreover, you can

play high or standard

quality still picture.

* PBC = PlayBack Control

This stereo system is equipped with the Dolby Pro

Logic Surround system* and the Dolby B-type noise

reduction system.

* Manufactured under license from Dolby

Laboratories Licensing Corporation.

DOLBY, the double-D symbol a and “PRO

LOGIC” are trademarks of Dolby Laboratories

Licensing Corporation.

02/02-03_MHC-V909AV.11E 98.11.9, 11:44 AM2

3

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Table of Contents

Getting Started

Step 1: Hooking up the system............. 4

Step 2: Setting up your speakers .......... 8

Step 3: Setting the time ........................ 10

Step 4: Presetting radio stations ......... 11

Connecting optional AV components 12

Basic Operations

Playing a VIDEO CD ........................... 15

Playing a CD ......................................... 17

Recording a CD/VIDEO CD .............. 18

Listening to the radio........................... 20

Recording from the radio .................... 22

Playing a tape........................................ 24

Recording from a tape ......................... 26

Singing along: Karaoke ....................... 27

The VIDEO CD/CD Player

Playing a VIDEO CD with PBC

functions (Ver 2.0) ......................... 29

Checking the remaining time ............. 31

Using the on-screen display ............... 32

Locating a specific part of a disc ........ 34

Playing a VIDEO CD from where it was

last stopped..................................... 39

Reducing distortion of the picture with

advanced DNR ............................... 40

Setting the sharpness ........................... 41

Adding trails to moving pictures....... 41

Playing CD tracks repeatedly ............. 42

Playing CD tracks in random order ......

.......................................................... 43

Programming CD tracks ..................... 44

Playing CDs without interruption ..... 45

The Tape Deck

Recording on a tape manually ........... 46

Recording a CD by specifying track

order ................................................ 47

DJ Effects

Looping part of a CD ........................... 49

Flashing part of a CD ........................... 49

Waving the equalizer ........................... 50

Sound Adjustment

Adjusting the sound ............................ 51

Selecting the surround menu ............. 52

Enjoying the Dolby Pro Logic Surround

sound ............................................... 53

Selecting the audio emphasis ............. 53

Adjusting the audio emphasis............ 55

Making a personal audio emphasis

file .................................................... 56

Other Features

Mixing and recording sounds ............ 57

Falling asleep to music ........................ 58

Waking up to music ............................. 58

Timer-recording radio programs ....... 60

Additional Information

Precautions ............................................ 61

Troubleshooting ................................... 62

Specifications ........................................ 65

Glossary ................................................. 67

Index........................................ back cover

02/02-03_MHC-V909AV.11E 98.11.9, 11:44 AM3

4

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Getting Started

Step 1: Hooking up the system

Do the following procedure 1 to 9 to hook up your system using the supplied cords and

accessories.

Left front speaker

Right front speaker

Right

surround speaker

Left

surround speaker

Center

surround speaker

FM lead antenna

AM loop antenna

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM4

5

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

continued

Black (’)

Red (‘)

Insert only the stripped portion.

R

L

+

–

Black (’)

Red (‘)

+

–

R

L

+

Insert only the stripped portion.

1

Connect the front speakers.

Connect the speaker cords to the

FRONT SPEAKER jacks of the same

color.

Keep the speaker cords away from the

antennas to prevent noise.

2

Connect the rear speakers.

Connect the speaker cords to the

SURROUND SPEAKER jacks of the

same color.

Keep the speaker cords away from the

antennas to prevent noise.

Black (’)Red (‘)

Insert only the stripped portion.

R

L

+

–

3

Connect the center speaker.

Connect the speaker cords to the

CENTER SURROUND SPEAKER jacks

of the same color.

Keep the speaker cords away from the

antennas to prevent noise.

4

Connect the FM/AM antennas.

Set up the AM loop antenna, then

connect it.

Extend the FM lead

antenna horizontally.

FM75

AM

AM loop antenna

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM5

6

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

If the color system of your TV is PAL:

Set SYSTEM SELECT to PAL.

Picture recorded in the NTSC color system will be

stretched horizontally and will be displayed with

the upper and lower parts of the screen masked in

black.

Note

Be sure to turn off the system before changing the

SYSTEM SELECT setting.

7 Set VOLTAGE SELECTOR to the

position of your local power line

voltage (except for Thailand and

Malaysian models).

8 Connect the power cord to a wall

outlet.

Demo mode appears in the display.

If the plug on this unit does not fit

your wall outlet, detach the supplied

adapter from the plug (except for

Malaysia and China).

9 Deactivate the demo mode by

pressing DISPLAY/DEMO when

the system power is turned off.

Step 1: Hooking up the system

(continued)

VID

EO

O

U

T

S VIDEO OUT

5 Connect the video input jack of your

TV to the VIDEO OUT jack with the

supplied video connecting cable.

When using a TV

Turn on the TV and select the video input so you

can view the pictures from this system.

Tip

For even higher quality video images, you can use

an optional S VIDEO cord to connect the S VIDEO

input jack on your TV to the S VIDEO OUT jack.

6 Set SYSTEM SELECT (color system)

to the appropriate position (PAL or

NTSC), according to your TV.

If your TV automatically changes the color

system according to the input signal:

The factory setting (AUTO) automatically

changes the color system of the video output

according to the color system of the current

VIDEO CD. If you turn off the system, the

color system will be set to NTSC

automatically when you turn on the system

again.

If the color system of your TV is NTSC:

Set SYSTEM SELECT to NTSC.

Picture recorded in the PAL color system will be

stretched vertically and will be displayed with the

upper and lower parts of the picture cut off.

SYSTEM SELECT

NTSC

PAL

AUTO

VOLTAGE SELECTOR

110-120V 220-240V

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM6

7

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Using the remote

You can use shaded the buttons shown below

to operate Sony TV.

To Press on the remote

Turn the TV on or TV POWER.

off

Switch the TV's TV/VIDEO.

video input

Change the TV TV CH +/–.

channels

Adjusts the volume TV VOL +/–.

of the TV speaker(s)

Tip

With normal use, the batteries should last for about

six months. When the remote no longer operates the

system, replace both batteries with new ones.

Note

If you do not use the remote for a long period of

time, remove the batteries to avoid possible damage

from battery leakage.

TV POWER

TV VOL +/–

TV CH +/–

TV/VIDEO

Inserting two size AA (R6)

batteries into the remote

To attach the center speaker pads

Attach the supplied center speaker pads to

the bottom of the center speaker to stabilize

the speakers and prevent them from slipping.

To attach the front speaker pads

Attach the supplied front speaker pads to the

bottom of the front speakers to stabilize the

speakers and prevent them from slipping.

Tip

You can reinforce the bass sound by connecting an

optional super woofer to the super woofer

connector.

Note

You need to connect both left and right rear

speakers. Otherwise, the sound will not be heard.

When carrying this system

Do the following to protect the CD

mechanism.

1 Press FUNCTION repeatedly until “CD”

appears in the display.

2 Hold down PLAY MODE and press

POWER so “LOCK” appears in the display.

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM7

8

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

2 Place the center speaker so it is

placed at about the same height as

the front speakers (A). Align the

center speaker with the front

speakers or place it slightly back

from the position of the front

speakers (B).

3 Place the rear speakers facing each

other at about 60 to 90 cm above

your listening position.

B

Center speaker

A

Rear speaker

60 to 90cm

Step 2: Setting up

your speakers

Front

speaker

(L)

Front

speaker

(R)

Center speaker

45°

Rear

speaker

(L)

Rear

speaker

(R)

Positioning the speakers

Before you connect them, determine the best

location for your speakers.

1 Place the front speakers at an angle

of 45 degrees from your listening

position.

Connecting the supplied rear and center

speakers enables you to fully enjoy Dolby Pro

Logic Surround sound. Dolby Pro Logic

Surround is a decoding system standardized

in TV programs and movies. Dolby Pro Logic

Surround improves sound image by using

four separate channels. These channels

manipulate the sound to be heard and

enhance the action as it happens on the

screen.

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM8

9

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

1

2,4

3

Adjusting the speaker

volume

To enjoy Dolby Pro Logic Surround sound,

turn the Dolby Pro Logic mode on, then

adjust the volume of each speaker using the

test tone that the system provides.

n

1 Press PRO LOGIC (or PRO LOGIC

ON/OFF on the remote).

“PRO LOGIC ON” appears.

2 Press T.TONE ON/OFF on the

remote.

The test tone is heard from the speakers

in the following order. Adjust the

volume of the test tone.

Front (left) n Center n Front (right)

3 From your listening position, press

CENTER LEVEL +/– and

REAR LEVEL +/– on the remote to

adjust the volume.

The volume levels from each speaker

must become the same.

4 Press T.TONE ON/OFF when you

are done adjusting.

The test tone is turned off.

Tip

If you turn VOLUME (or press VOL +/– on the

remote) all the speaker volumes change.

Rear

POWER

1

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM9

10

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

1 Press CLOCK/TIMER SET.

The hour indication flashes.

2 Turn the jog dial to set the hour.

The clock is on a 12-hour system.

3 Press ENTER/NEXT.

The minute indication flashes.

4 Turn the jog dial to set the minute.

5 Press ENTER/NEXT.

The clock starts working.

Step 3: Setting the

time

You must set the time before using the timer

functions.

1 3,52,4

Tips

• If you’ve made a mistake, start over from step 1.

• Setting the time deactivates the demo mode.

If you want to display the demo mode, press

DISPLAY/DEMO when the power is off.

Note

When setting the time, set the equalizer display to

anything other than Spectrum analyzer pattern 3.

(See “To change the equalizer display” on page 54.)

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM10

11

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Step 4: Presetting

radio stations

You can preset up to 40 stations, 20 for FM, 10

for MW and 10 for SW. For 2 band models,

you can preset up to 30 stations, 20 for FM

and 10 for AM.

1 Press TUNER/BAND repeatedly

until the band you want appears in

the display.

Each time you press this button, the

band changes as follows:

2 band model:

FM ˜ AM

3 band model:

FM n MW n SW

2 Press TUNING MODE repeatedly to

select “AUTO.”

n

3,56214

POWER

TUNED

STEREO

MHz

VOLUME

AUTO

TUNED

STEREO

VOLUME

AUTO

Preset number

3 Turn the jog dial.

The frequency indication changes and

scanning stops when the system tunes in

a station. “TUNED” and “STEREO” (for

stereo programs) appear.

4 Press TUNER MEMORY.

A preset number appears in the display.

5 Turn the jog dial to select the preset

number you want.

6 Press ENTER/NEXT.

The station is stored.

7 Repeat steps 1 to 6 to store other

stations.

To tune in a station with a weak

signal

Press TUNING MODE repeatedly to select

“MANUAL” in step 2, then turn the jog dial

to tune in the station.

To change the preset number

Start over from step 1.

To change the AM tuning interval

The AM tuning interval is factory-preset to 9 kHz.

To change the AM tuning interval, tune in any AM

station first, then turn off the power. While holding

down the ENTER/NEXT button, turn the power

back on. When you change the interval, AM preset

stations will be erased. To reset the interval, repeat

the same procedure.

Tip

The preset stations are retained for half a day even if

you unplug the power cord or a power failure

occurs.

03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM11

12

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

To the audio outputs

of the MD deck

To the audio inputs

of the MD deck

Connecting optional

AV components

To enhance your system, you can connect

optional components. Refer to the

instructions of each component.

Connecting audio

components

Select one of the following two connections,

depending on the equipment to be connected

and method of connecting.

Connecting an MD deck for digital

recording

You can record from a CD to an MD deck

digitally by connecting an optical cable.

To the DIGITAL IN jack of the MD deck

Connecting an MD deck for analog

recording

Be sure to match the color of the plugs and

the connectors. To listen to the sound of the

connected MD deck, press FUNCTION

repeatedly until “MD” appears.

Note

If you cannot select “MD” by pressing FUNCTION,

press POWER while pressing FUNCTION when the

power is turned off. “VIDEO” will be switched to

“MD.” To return to “VIDEO,” do the same

procedure.

Tip

If you connect a turntable with an MM cartridge,

connect it to VIDEO/MD IN using the optional MM

cartridge equalizer and an audio connecting cord.

To listen to the sound, press FUNCTION repeatedly

until “VIDEO” or “MD” appears.

Note

You cannot record from a VIDEO CD to an MD

deck digitally. When you record from a VIDEO CD

to an MD deck, connect an optional audio cable to

the audio output. (See “Connecting an MD deck for

analog recording.”)

04/12-14_MHC-V909AV.11E 98.11.9, 11:45 AM12

13

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

To super woofer

Connecting a VCR

Be sure to match the color of the plugs and

the connectors. To listen to the sound of the

connected VCR, press FUNCTION repeatedly

until “VIDEO” appears.

By connecting the audio output jacks of your

VCR to the VIDEO/MD (AUDIO) IN jacks

using an optional audio cable, you can enjoy

video playback in powerful stereo sound.

Moreover, if you connect the video input on

the VCR to the VIDEO/MD (AUDIO) OUT

jacks and VIDEO OUT (or S VIDEO OUT)

jack using the supplied video connecting

cable (or an optional S VIDEO connecting

cable), you can record the audio and video

signals from a VIDEO CD onto video tape.

Note

If the sound is distorted when selecting “VIDEO,”

switch to “MD” (see “Note” on page 12).

Connecting a super woofer

speaker

You can connect an optional super woofer

speaker.

To the audio outputs

of the VCR using an

optional audio cable

To the video input

of the VCR using a

video cable

To the S VIDEO input of

the VCR using an

optional S VIDEO cable

To the audio inputs of

the VCR using an

optional audio cable

04/12-14_MHC-V909AV.11E 98.11.9, 11:45 AM13

14

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Connecting outdoor

antennas

Connect the outdoor antenna to improve the

reception.

FM antenna

Connect an optional FM outdoor antenna.

You can also use the TV antenna instead.

AM antenna

Connect a 6 to 15 meter (20 to 50 feet)

insulated wire to the AM antenna terminal.

Leave the supplied AM loop antenna

connected.

Important

If you connect an outdoor antenna, ground

from y terminal with the screw clamp. To

prevent a gas explosion, do not connect the

ground wire to a gas pipe.

FM75

AM

y

75-ohm coaxial cable

(not supplied)

Screw clamp

Ground wire (not supplied)

FM75

AM

y

Screw clamp

Ground wire (not supplied)

Insulated wire (not supplied)

04/12-14_MHC-V909AV.11E 98.11.9, 11:45 AM14

Basic Operations

15

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Basic Operations

1 Turn on your TV and select the

video input.

Refer to the operating instructions

supplied with your TV if you need help.

2 Press § OPEN/CLOSE and place

up to two VIDEO CDs on the disc

tray.

If a disc is not placed properly, it will not

be recognized.

To insert a third disc, press DISC SKIP

EX-CHANGE to rotate the disc tray.

3 Press one of the DISC 1~3 buttons.

The disc tray closes and playback starts.

If you press ·∏ (or SELECT CD ( on

the remote) when the disc tray is closed,

playback starts from the CD whose

button is lit green.

Playing a VIDEO CD

You can play both VIDEO CDs without PBC

functions (Ver 1.1) and VIDEO CDs with PBC

functions (Ver 2.0).

You can enjoy two kinds of playback

according to the disc type.

jog dial

·∏

With the label

side up. When

you play a

VIDEO CD

single, place it

on the inner

circle of the

tray.

·∏

§

π

0)

+=

2

1/ALL

DISCS

p

VOLUME

D.SKIP

P

SELECT

CD (

0/)

p

PREV– /

NEXT+

TV POWER

TV VOL +/–

TV CH +/–

Disc tray number Playing time

Track number

VOLUME

ALL 1DISCS

VOL +/–

0/)

DISC SKIP

EX-CHANGE

POWER

3

continued

05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM15

16

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

To Do this

Stop playback Press p.

Pause Press ·∏ (or P on the

remote)*

1

.

Resume playbackPress ·∏ (or SELECT CD (

on the remote).

Select a track or Press NEXT+ to go foward, or

scene PREV– to go back.

Or during playback or pause,

turn the jog dial clockwise (to

go forward) or

counterclockwise (to go back)

and release it when you reach

the desired track*

2

.

Find a point in a Press and hold 0 or )

track or scene*

2

during playback, and release

at the desired point.

Select a CD Press one of DISC 1~3 button.

in stop mode Or press DISC SKIP EX-

CHANGE (or D. SKIP on the

remote).

Play only the Press 1/ALL DISCS repeatedly

VIDEO CD you until “1 DISC” appears.

have selected

Play all VIDEO Press 1/ALL DISCS repeatedly

CDs*

3

until “ALL DISCS” appears.

Remove or Press § OPEN/CLOSE.

change the

VIDEO CDs

Adjust the Turn VOLUME (or press

volume VOL +/– on the remote.

*

1

There may be some disturbance in the video

image.

*

2

Only for VIDEO CDs without PBC functions (Ver

1.1).

*

3

This function cannot be used during menu

playback of a VIDEO CD with the PBC functions

(Ver 2.0).

Tips

• Pressing ·∏ when the power is off

automatically turns the power on and starts

VIDEO CD playback if there is a VIDEO CD in the

tray (One Touch Play).

• You can switch from another source to the VIDEO

CD player and start playing a VIDEO CD just by

pressing ·∏ or the DISC 1~3 buttons

(Automatic Source Selection).

• If there is no VIDEO CD in the player,

“CD NO DISC” appears in the display.

• When a disc is selected or the VIDEO CD placed

in that position is playing, the DISC 1~3 button for

that position lights green.

Playing a VIDEO CD (continued)

05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM16

Basic Operations

17

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Playing a CD

— Normal Play

1 Press § OPEN/CLOSE and place

up to two CDs on the disc tray.

If a disc is not placed properly it will not

be recognized.

To insert a third disc, press DISC SKIP

EX-CHANGE to rotate the disc tray.

2 Press one of the DISC 1~3 buttons.

The disc tray closes and playback starts.

If you press ·∏ (or SELECT CD ( on

the remote) when the disc tray is closed,

playback starts from the CD loaded on

the tray whose button is lit green.

You can play up to three CDs in a row.

With the label

side up. When

you play a single

CD, place it on

the inner circle

of the tray.

·∏

§

π

0)

+=

2

1

Disc tray number

Playing time

Track number

VOLUME

ALL 1DISCS

·∏

p

jog dialDISC SKIP

EX-CHANGE

1/ALL

DISCS

VOLUME

P

=/+

0/)

p

VOL +/–

D.SKIP

0/)

POWER

continued

SELECT

CD (

05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM17

18

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

Recording a CD/VIDEO

CD

— CD Synchro Recording

The CD SYNCHRO button lets you record

audio sources from a CD/VIDEO CD to a

tape easily. You can use TYPE I (normal) or

TYPE II (CrO2) tapes.

1

2

53

π

4

DISC SKIP

EX-CHANGE

DOLBY NR

POWER

Tips

• Pressing ·∏ when the power is off

automatically turns the power on and starts CD

playback if there is a CD in the tray (One Touch

Play).

• You can switch from another source to the CD

player and start playing a CD just by pressing

·∏ or the DISC 1~3 buttons (Automatic Source

Selection).

• If there is no CD in the player, “CD NO DISC”

appears in the display.

• When a disc tray is selected or the CD placed on

that tray is playing, the DISC 1~3 button for the

respective tray lights green.

To Do this

Stop playback Press p.

Pause Press ·∏ (or P on the

remote). Press again to resume

play.

Select a track During playback or pause,

turn the jog dial clockwise (to

go forward) or

counterclockwise (to go back)

and release it when you reach

the desired track. Or press +

(to go forward) or = (to go

back) on the remote.

Find a point in Press and hold down ) or

a track 0 during playback and

release it at the desired point.

Select a CD Press a DISC 1~3 button or

in stop mode DISC SKIP EX-CHANGE (or

D. SKIP on the remote).

Play only the Press 1/ALL DISCS

CD you have repeatedly until “1 DISC”

selected appears.

Play all CDs Press 1/ALL DISCS repeatedly

until “ALL DISCS” appears.

Remove the CD Press § OPEN/CLOSE.

Exchange other Press DISC SKIP

CDs while EX-CHANGE (or D. SKIP on

playing the remote).

Adjust the Turn VOLUME (or press

volume VOL +/– on the remote).

Playing a CD (continued)

05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM18

Basic Operations

19

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

1 Press § and insert a blank tape into

deck B.

2 Press § OPEN/CLOSE and place a

CD.

Then press again to close the disc tray.

If the indicator for the tray you want to

record is not lit green, press DISC SKIP

EX-CHANGE repeatedly so that it lights

green.

3 Press CD SYNCHRO.

Deck B stands by for recording and the

CD player stands by for playback. ·

(for front side) lights up.

4 Press DIRECTION repeatedly to

select A to record on one side.

Select a (or RELAY) to record on

both sides.

5 Press ∏ PAUSE on deck B.

Recording starts.

With the label

side up. When

you play a single

CD, place it on

the inner circle

of the tray.

·∏

§

π

0)

+=

§

‚º

π

ª·

With the side

you want to

record facing

forward.

To stop recording

Press π on deck B or p on the CD player.

Tips

• If you want to record from the reverse side, press

ª so that ª (for reverse side) lights up.

• When you record on both sides, be sure to start

from the front side. If you start from the reverse

side, recording stops at the end of the reverse side.

• When you want to reduce the hiss noise in low-

level high-frequency signals, press DOLBY NR on

the remote so that “DOLBY NR B” appears after

pressing CD SYNCHRO.

Notes

• You cannot listen to other sources while recording.

• You cannot record from a VIDEO CD with PBC

functions (Ver 2.0).

05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM19

20

SONY MHC-V909AV (E) 3-860-316-11Actual page number:

n

TUNED

STEREO

MHz

VOLUME

PRESET

Preset number Frequency

Listening to the radio

–– Preset Tuning

Preset radio stations in the tuner's memory

first (see “Step 4: Presetting radio stations”).

12

3

n

1 Press TUNER/BAND repeatedly

until the band you want appears in

the display.

Every time you press the button, the

band changes as follows:

2 band model:

FM ˜ AM

3 band model:

FM n MW n SW

2 Press TUNING MODE repeatedly

so “PRESET” appears in the display.

MANUAL n AUTO n PRESET

3 Turn the jog dial (or press = or

+ on the remote) to tune in the

desired preset station.

To Do this

Turn off the radio Press POWER.

Adjust the volume Turn VOLUME (or press

VOL +/– on the remote).

STEREO /

MONO

VOLUME

=/+

VOL +/–

TUNER/

BAND

Turn

counterclockwise

(or press =

on the remote)

for lower preset

numbers.

Turn clockwise

(or press +

on the remote)

for higher

preset numbers.

+–

POWER

05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM20

Page is loading ...

Sony MHC-V909AV Operating instructions

Sony MHC-V909AV Operating instructions

Related papers

Other documents