39
Keep-warm Function
By using the buttons 70, 80 and 90, the temperature will be
kept steady for 2 hours. The appliance then enters standby
mode.
NOTE:
Not for 100 °C! The keep warm function cannot be
combined with this temperature. After the water has
been heated to 100 °C, the appliance switches off after
60 seconds.
Child Lock
You can lock the buttons to prevent the appliance from
being switched on accidentally.
• Press and hold the 70 and 100 buttons simultaneously
for about 3 seconds to enable child lock. A bar is ashing
in the display.
• You have two options for disabling child lock again. The
bar in the display will disappear.
- Simultaneously press the buttons 70 and 100 once
more for about 3 seconds.
- Remove the appliance from the base.
Mains Lead
Completely unwind the length of mains lead that you require
from the bottom section of the base. Please ensure that the
mains lead does not become tangled up.
Connected Wattage
The total power consumption of this appliance can be up to
1100 W. Do not use any multiple sockets, as this appliance
is too powerful.
Electrical Connection
1. Check whether the mains voltage that you want to use,
corresponds with that of the appliance. You will nd the
information about it on the rating plate.
2. Only connect the appliance to a properly installed safety
socket.
Switching the Appliance On / Off
• Press any button to switch the appliance on. A beep will
sound and the current water temperature appears in the
display.
• To switch the appliance off, press and hold the 100 button
for about 3 seconds. A beep will sound and the display
goes off.
Preparation
Before using for the rst time, boil fresh water at least three
times in the appliance. Use only water without any additives
or ingredients.
Operation
NOTE:
Always use fresh, cold water.
1. Place the appliance on a at surface.
2. Remove the lid by using the handle (2) to pull it up.
3. Then ll in the water (max. 0.5 litre). You can read the
lling level on the water level indicator of the kettle.
4. Open the tea strainer by twisting it slightly towards
OPEN.
5. Choose your tea dosage. Mount the tea strainer to the
push rod again. Therefor slightly twist it towards LOCK.
NOTE:
• For some teas with large herbal leaves (e. g.
peppermint) we recommend shredding or crushing
them so that it can develop its aroma better.
• The tea strainer should only be immersed in water
if the desired temperature has been reached.
6. Put the lid back on.
7. Place the appliance ush on the base.
8. Switch on the appliance.
9. Use the corresponding button to select a temperature.
The number of the button lights up and the appliance is
switched on.
10. You can dip the tea strainer into the water once you
boiled it. Use the handle (3) to slide the push rod down.
Use the push rod to determine when and for how long
the tea is supposed to brew.
NOTE:
• When the temperature is reached, you will hear a
beep.
• The lamp on the temperature button lights up. The
appliance will now keep the temperature stable for
2 hours and then switch off.
• The keep warm will remain active, even if you take the
jug from the base for up to a minute.
• Not for 100 °C! The keep warm function cannot be
combined with this temperature.
WARNING: Risk of burns!
• The hosing becomes hot during operation, do not
touch it.
• Be aware of escaping steam when removing the lid.
• The tea strainer becomes hot! Be careful when remov-
ing. If necessary, use a potholder. The tea strainer will
continue to drip!
Ending / Terminating Operation
There are two options to interrupt the boiling process or to
terminate it:
• The appliance will switch off after the boiling process.
• To switch the appliance off, press and hold the 100 button
for about 3 seconds.