Whirlpool GZ5730XR Owner's manual

Brand: Whirlpool

Model: GZ5730XR

Category: Cooker hoods

Type: Owner's manual

(91.4 cm)

(76_2cm) et S6"(91_

Table of Contents/Table des matieres ............................................................................. 2

GZ5730XR Series

GZ5736XR Series

S6rie GZ5730XR

Serie GZ5736XR

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS,

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS,

POUR UTILISATION Rm_SlDENTIELLE UNIQUEMENT.

iMPORTANT:

installer: Leave installation instructions with the homeowner,

Homeowner: Keep installation instructions for future reference.

Save installation instructions for local inspector's use.

iMPORTANT :

lnstallateur : Remettre les instructions d'installation au propri6taire.

Propd_taire : Conserver Ies instructions d'installation pour consultation ulterieure.

Conserver les instructions d'installation pour consultation par I'inspecteur local.

628014A/9763367

TABLEOF CONTENTS

RANGE HOOD SAFETY ............................... 2

iNSTALLATiON REQUIREMENTS ....................... 4

Tools and Parts ..................................... 4

LocationRequirements ............................ 4

ElectricaIRequirements ............................ 4

Venting Requirements ............................. 5

INSTALLATION INSTRUCTIONS ........................6

Prepare Location ................................. 6

Prepare the Hood ................................. 6

Make EIectrica[Connection ......................... 8

Instal[Range Hood ................................ 9

Complete Installation .............................. 9

RANGE HOOD USE .................................. 10

Operation ...................................... 10

RANGE HOOD CARE ................................ 10

CHeaning and Maintenance ........................ 10

REQUESTING ASSISTANCE OR SERVICE .............. 1t

RANGE HOOD WARRANTY ........................... 12

TABLEDESMATIERES

S¢:CURITE DE LA HOT'rE DE CUISINI_:RE .............. 13

EXIGENCES D'INSTALLATION ........................ 15

Outillage et pi6ces ..................................15

Exigences d'ernphcernent ......................... 15

SpecificationselectMques ......................... 16

Exigences concernant I'evacuation................. 16

INSTRUCTIONS D"INSTALLATION ..................... 18

Preparation de H'empHacement ..................... 18

Preparation de la hotte ........................... 18

RaccordernenteIectrique.......................... 20

Installationde [a hottede cuisiniere................21

Achever HnstaIIafion............................. 21

UTILISATION DE LA HOTTE DE CUISINI_:RE ............ 22

Foncfionnement ................................. 22

ENTRETIEN DE LA HoTrE DE OUISINI_:RE ............. 22

Nettoyage et entretien ............................ 22

DEMANDE D"ASSlSTANCE OU DE SERVICE ............ 23

GARANTIE DE LA HOTTE DE CUISINI_:RE .............. 24

RANGEHOODSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RiSK OF FIRE, ELECTRIC

SHOCK, OR iNJURY TO PERSONS, OBSERVE THE

FOLLOWING:

m Use this unit only in the manner intended by the

manufacturer, if you have questions, contact the

manufacturer.

m Before servicing or cieaning the unit, switch the power off at

the service panel disconnecting means to prevent power

from being switched on accidentalIy. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service

panel.

m installation work and electricaJ wiring must be done by

qualified person(s) in accordance with all applicable codes

& standards, including fire-rated construction.

m Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

m When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

m Ducted systems must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls ceilings, attics, crawl spaces, or

garages.

WARNING: TO REDUCE THE RiSK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RiSK OF A RANGE TOP

GREASE FIRE:

m Never leave the surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oiJs siowiy on low or medium settings.

m Always turn hood ON when cooking at high heat or when

flameing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe).

m Clean ventilating fans frequently. Grease shouId not be

allowed to accumulate on fan or filter.

m Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RiSK OF iNJURY TO

PERSONS iN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

m SMOTHER FLAMES with a close fitting Iid, cookie sheet, or

other metal tray, then turn off the gas burner or electric

element. BE CAREFUL TO PREVENT BURNS. if the

flames do not go out immediately, EVACUATE AND CALL

THE FiRE DEPARTMENT.

m NEVER PiCK UP A FLAMING PAN - you may be burned.

m DO NOT USE WATER, including wet dishcloths or towels -

a vioIent steam explosion wiiI result.

m Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

m WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

SAVE THESE iNSTRUCTiONS

iNSTALLATiONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the safety instructions provided with any tools

listed here.

Tools needed:

level

_, compass or 8" (20.3 cm) circle template

_, flat blade screwdriver

Phillips screwdriver

_, pliers

_, metal snips

drill

11/4"and 1/8"drilIbits

_, pencil

ruler

_, keyhole saw

saber saw

duct tape

Parts needed:

_, UL- or CSA-Iisted, 1/,,,(12.5 mm) strain relief

(used with direct wiring only)

_, power supply cable

_, 7" (17.8 cm) round damper if using

7" (17.8 cm) round vent system

2 twist-on electrical wire connectors

IMPORTANT: Observe all governing codes and ordinances.

Hood location should be away from strong draft areas, such as

windows, doors and strong heating vents.

Grounded electricaI outlet is required. See "Electrical

Requirements" section.

It is recommended that the hood be fastened into solid wood. If

fastening into drywall or other material, wall anchors or screws

with toggle nuts (purchased separately) must be used.

This hood is factory set for non-venting (recirculating)

installations. For vented installations see "Installation Instructions"

section.

If this hood will be used as a non-vented installation you will also

need to purchase a 30" (76.2 cm) Filter Kit, No. 4396291 or

36" (91.4 cm) Filter Kit, No. 4396292 from your dealer.

All openings in ceiling and wall where the hood will be installed

must be sealed.

In U.S. only: For power cord connected installations, a UL-listed

range hood cord-connection kit (part no. 99524057) must be

used. Cord kit has not been evaluated for use in Canada.

Product Dimensions

IMPORTANT: The hood must be electrically grounded in

accordance with local codes and ordinances, or in the absence of

local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

[] A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is

required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this hood be provided.

[] Do not ground to a gas pipe.

[] Check with a qualified electrician if you are not sure range

hood is properly grounded.

[] Do not have a fuse in the neutral or ground circuit.

[] The range hood must be connected with copper wire only.

[] The range hood should be connected directly to the fused

disconnect (or circuit breaker) box through flexible armored or

nonmetallic sheathed copper cable.

[] A UL- or CSA-listed strain relid must be provided at each end

of the power supply cable. Wire sizes (copper wire only) and

connections must conform with the rating of the appliance as

specified on the model/serial rating plate.

[] Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70, latest edition, or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C222 No. 0-M91, latest edition, and all local codes and

ordinances.

[] Ventsystem(ifneeded)forinstallationisnotincluded.

[] Ventsystemmustterminatetotheoutside.

[] Donotterminatetheventsysteminanatticorother

enclosedarea.

[] Donotuse4"(10.2cm)laundry-typewallcaps.

[] Usemetalventonly.Rigidmetalventisrecommended.Do

notuseplasticormetalfoilvent.

Forthemostefficientandquietoperation:

[] Thelengthoftheventsystemandnumberofelbowsshould

bekepttoaminimumtoprovideefficientperformance.The

sizeoftheventsystemshouldbeuniform.

[] Donotinstalltwoelbowstogether.

[] Ventsystemcanterminateeitherthroughtherooforwail.

[] Forthemostefficientandquietoperation,itisrecommended

thattherangebeventedverticallythroughtheroofthrough

7"(17.8cm)roundventsystem.

[] Useducttapetosea!alljointsintheventsystem.

[] Usecaulkingtosealexteriorwallorroofopeningaround

thecap.

VentingMethods

Determinewhichoutsideventingmethodneedstobeused.Itis

recommendedthattheventsystembeinstalledbeforeinstalling

thehood.

NOTE:Ifanon-vented(recirculating)installationisdesired,follow

instructionsinthe"MakeElectricalConnection"section.

7" (17.8 cm) round

or 3-1/4" x 10" , roof cap 7" (17,8 cm)

(8,3 x 25,4 cm) round

round damper

(purchased

separately)

i I

24"(61cm) to _

30"(782 cm)

abovecooking

surface

Roof venting Wall venting

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Use 31/4'' x 10" (8.3 x 25.4 cm) or 7" (17.8 cm) round vent with a

maximum length of 65 feet (19.8 m) for vent system. For best

performance, use no more than three 90° elbows. To calculate the

length of system you need, add the equivalent feet for each vent

piece used in the system. See the examples below.

3-1/4" x 10" (8.3 x 25.4 cm) vent system

Recommended standard fittings

Vent piece 31/4"x 10" (8.3 x 25.4 cm)

31/4'' x 10" 5 feet

(8.3 x 25.4 cm) (1.5 m)

90° elbow

31/4"x 10" 12 feet

(8.3 x 25.4 cm) (3.7 m)

flat elbow

31J411 X 10 H 0feet ....

(8.3 x 25.4 cm) (0 m)

wa,oap

3-1/4" x 10"

(8_3x 25_4 cm) _6 ft. 1.8 m _ wall cap

e,bow _ ____ Exampie vent

system

2ft. 1 -- 90 elbow = 5 ft. (1.5 m)

(u_lm_l I_ ' 8 ft. (2.4 m) straight = 8 ft. (2.4 m)

Jh' '

_-_ 1 -- wall cap = 0 ft. (0 m)

h_J system length = 13 ft. (3.9 m)

7" (17.8 cm} vent system

Recommended standard fittings

Vent piece

450elbow

900 elbow

7" (17.8 cm)

wall cap

7" (!7.8 cm) round

2.5 feet

(0.8m)

5.0 feet

(1.5 m)

0 feet

(0m)

Vent piece

31/4,,x 10,,

(8.3 x 25.4 cm

to 7" (17.8 cm)

31/4,,x 10,,

(8.3 x 25.4 cm

to 7" (17.8 cm)

90° elbow

_" (!7.8 cm) round

4.5 feet

/14©.....

90° elbow _6 ft. (1.8 m)_l wall cap

_.q -----._--_ Example vent

( I

ft.

system length = 13 ft. (3.9 m)

iNSTALLATiONiNSTRUCTiONS

1. If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to upper

cabinet or rear wall. Slide cardboard or hardboard under

range before moving range across floor to prevent damaging

floor covering. Otherwise put a thick, protective covering over

countertop, cooktop or range to protect from damage

or dirt.

2. Determine which venting method (roof or wall venting or

non-venting) you need to use. This range hood is shipped for

non-vented installation.

7" {17,8 cm) round vertica_ vent system

wall 5" 1V4"(3.2 cm) 2"

(122 cm) dia. hole (5_1cm)

wall W' (3.0 ram) 1F,"

pilot holes (3.8 cm)

Hood size A

30" (76,2 cm) 13_%'' (35,4 cm)

36" (91,4 cm) 16_5A6'' (43,0 cm)

wood shim strips

(recessedcabinet

bottoms only)

3V4" x 10" {8,3 x 25,4 cm} horizonta_ vent system

centerline

"",,q 1¼" (3,2cm)

3¾"

(9_8cm)

(3.2ram) 511/_,,__7,/,, ' (19(19c2)m)

(13.3 cm)

Drill four W' (3.0 mm) pilot holes for hood mounting screws. If

cabinet has recessed bottom, add wood shim strips on each

side.

From the following diagrams, select the diagram for your

installation.

Vented installations: Cut the vent system and electricN wiring

access holes as required.

Non-vented installations: Drill only the 1_/_"(3.2 cm) dia. wiring

access hole required.

[] If wiring through the top, use location shown in vertical

vent systems.

[] If wiring through the back, use location shown in

3%" x t0" {8,3 x 25,4 era) rectangular vertica_ vent system

5w'

horizontal vent system.

Set the hood on a protective covering such as cardboard or a

large towel. Remove the 7" (17.8 cm) round vent plate from

5" 1W' wall 1V4"(3.2 cm) 2"

(12.7cm) (3,2cm) dia, hole (5,1cm)

A. 7" (17.8 cm) round vent plate

top of hood. Set vent plate and mounting screws aside,

Remove tape holding standard filters in place. Remove both

filters. Insert flat blade screwdriver into slots in filters. Push

, B

A. Filterslots

B.Flatbladescrewdriver

each filter toward back of hood, lift out and set aside,

Remove damper/vent connector from inside the hood. Set

js _

A _ IJ

A,Damper/ventconnector

connector, mounting screws and parts bag aside,

Remove wiring cover from inside the hood. Set cover and

A. Hiring cover

mounting screw aside,

Depending on your installation, remove either top or back

wiring knockout and install a 1/2"UL- or CSA-listed strain

A. Strainrelief

relief,

For r_or_=vented installations

Go to "Make ElectricaI Connection" section,

For vented installations

1, Remove the five screws holding the light panel in place and

set them aside.

2, Disconnect the light assembly wiring connector.

Make sure not to disconnect any wires.

3, Remove the light panel and set aside.

A \

A. Light panel

Remove the air chute held in place with one screw.

A,Airchute

Remove baffle from air chute.

A, Baffle

Rotate baffle and reinsert it back into the air chute so that the

baffle tabs fit all the way into the slots in the air baffle.This will

close off the air flow through the non-vented slots on top of

the hood.

A. Tabslots

B. Tabs

Replace air chute.

Connect light assembiy wiring connector and replace light

panel.

NOT_:: Make sure not to trap wires between the support fin

and light panel.

Remove either top or rear rectangular knockout, if using 7"

(17.8 cm) round vent, remove both top rectangular knockout

and the semi-circular knockout.

Direct Wiring installation

--- __.

A. Semi-circularknockout

B.Toprectangularknockout

C.Rearrectangularknockout

10, install damper:

Vortical vent

position

B Horizontal vent

position

A. Up to 1" (2.5 cm) side-to-side adjustment

B. Pivot

C. Damper/vent connector

Rectangular vent only:

Attach damper/vent connector over knockout opening. Make

sure damper pivot is nearest to top/back edge of hood,

Remove tape from damper flap.

NOTE: For horizontal vent systems, it is recommended that

the rectangular ventwork be attached to the damper/vent

connector and sealed with duct tape before installing the

hood.

Round vent only:

Replace round vent plate removed in step 1 of "Prepare the

Hood" section.

Install a 7" (17.8 cm) round damper (must be purchased

separately). The damper flap must open freely in the direction

of air flow (away from range hood),

NOTE: Damper/vent connector and round vent plate can be

installed up to 1" (2.5 cm) on either side of hood center if

ventwork is off-center, in extreme off-center installations, one

end of the vent connector may need to be trimmed to clear

the electrical strain relief.

Electdcam Shock Hazard

Disconnect power before servicing.

Replace all parts and panemsbefore operating.

Failure to do so can resuJt in death or emectrical shock,

EmectdcaI Shock Hazard

Electrically ground the blower.

Connect ground wire to green ground screw in

wiring box.

Paimureto do so can resumt in death or eiectricam shock.

1, Disconnect power.

2, If not previously done, run wiring through wall or cabinets

according to electrical codes and ordinances,

3, Stand hood up as shown, (Keep on protective cover to

protect hood and cooking sudace,) Feed the power supply

cable through the strain relief.

i_¸ ,

4, Use twist-on connectors and connect black wires together.

5, Use twist-on connectors and connect white wires together.

6, Connectthepowersupplygroundwiretothegreenground

connectorandtightensecurely.

3, Positiontherangehoodsothatthelargeendofthekeyhole

slotsareoverthescrews.Thenpushthehoodtowardthewall

sothatthescrewsareintheneckoftheslots.

.... A

A. Green ground connector

7, Securely tighten the strain relief.

8, Replace the wiring cover.

UL-Listed Power Supply Cord Kit {U.S. Only}

1, Connect a ULqisted Power Cord Kit (part no=99524057) (U.S=

only) following the kit instructions for connecting the wires.

2, Replace the wiring cover.

A, Keyhole slots (4)

B. Mounting screw

4, Tighten mounting screws to cabinet, making sure mounting

screws are in narrow neck of slots.

On vented installations:

5, Make sure that damper blade opens and closes freely.

6, Connect ventwork to hood. Sea! joints with duct tape to make

them secure and air tight.

Remove the 4 hood mounting screws from the parts bag and

install in previously drilled 1/8"(3.0 mm) pilot holes. Leave

screw heads about 1/4"(6.4 mm) away from shim strips.

1, Install (2) PAR20, 50W maximum halogen bulbs or (2) R16,

40W maximum incandescent bulbs. Bulbs purchased

separately.

2, Replace filters.

NOTE: Filter slot must be toward front of hood.

For non-vented installations: Attach the charcoal filters (not

supplied) to the aluminum filters with the special blue and

yellow strips facing toward the cooking surface. Make sure

fan blade turns freely.

3, Reconnect power.

4, Check for proper operation.

2, Lift range hood into final position, feeding electrical wire

through wiring opening. To avoid damage, do not push on fan

blade.

RANGEHOODUSE RANGEHOODCARE

Hood control panel

0 A --% ......................B

HIGH LO

A. Fanswitch

B.Lightswitch

Operating the fan

A 3-position rocker switch controls the fan. The left position is low

speed, center position is off, and the right position is high speed,

An indicator light shows that the fan is on,

Operating the _ight

A 3-position rocker switch controls the lights. The left position is

low light intensity, center position is off, and the right position is

high light intensity,

Replacing the light bulbs

Before you begin, make sure that the range hood is turned off

and that the lamps have had sufficient time to cool. Halogen

bulbs burn extremely hot. See bulb packaging for further

information.

Replace with (2) PAR20, 50W maximum halogen bulbs or

(2) R16, 40W maximum incandescent bulbs.

: !::: ::: :

Be sure lights are cool before cleaning the hood,

To clean hood

1, Disconnect power,

2, Remove filters,

3, Use a damp cloth and a mild detergent to wipe all grease-

laden surfaces. Use care when cleaning fan blade - it must

not become bent or misaligned, Do not allow water to enter

the motor,

4, Make sure all surfaces are completely dry before replacing

filters,

5, Reconnect power,

Motor is permanently lubricated. Do not oil or disassemble motor,

A_uminum mesh filters

Clean often using hot water and a mild detergent. Filters are

dishwasher safe.

Charcoal fiRers (non-vented installations)

[] Clean filter surfaces frequently with a damp cloth and mild

detergent, Do not immerse filters in water or put in

dishwasher,

[] Special blue and yellow strips will blend to green when it is

time to change the filter. These strips work best when facing

toward the cooking surface,

[] 30" (76.2 cm) Filter Kit No. 4396291 or 36" (91.4 cm) Filter Kit

No. 4396292 is available from your dealer.

REQUESTINGASSISTANCEORSERVICE

if you need assistance or service in U.S.A.

Call the Whirlpool Customer hteraction Center toll=free at

1-800-253-1301o Our censuBtants are available to assist you°

When calling: Please know the purchase date, and the complete

model and serial number of your appliance This information wilI

help us better respond to your request.

Our consultants provide assistance with:

_, Features and specifications on our full Iine of appliances

_, Installation information

_, Use and maintenance procedures

_, Accessory and repair parts sales

_, Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.)

_, Referrals to Iocal dealers, service companies, and repair parts

distributors

Whirlpool designated service technicians are trained to fulfill the

product warranty and provide after-warranty service, anywhere in

the United States.

To locate the designated service company in your area, you can

also look in your telephone directory Yellow Pages.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory-authorized parts. These parts will fit right and

work right, because they are made to the same exacting specifi-

cations used to build every new Whirlpool appliance.

To locate factory-authorized parts in your area, call our Customer

Interaction Center telephone number, your nearest authorized

service center, or 1-800-442-1111.

For further assistance

If you need further assistance, you can write to Whirlpool with any

questions or concerns at:

Customer Interaction Center

c/o Correspondence Dept.

2000 North M-63

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

if you need assistance or service in Canada

For product related questions, please cail the Whirlpool Canada

LR Customer Interaction Center toll free: 1-800=461=5681

Monday to Friday 8:00 a.m. - 6:00 p.m. (EST).

Saturday 8:30 a.m. - 4:30 p.m. (EST).

Our consultants provide assistance with:

[] Features and specifications on our full line of appliances.

[] Referrals to Iocal dealers.

For parts, accessories and service in Canada

Call 1=800-807=6777° Whirlpool Canada LR designated service

technicians are trained to fulfill the product warranty and provide

after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool Canada

LR with any questions or concerns at:

Customer Interaction Center

Whirlpool Canada, LR

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

WHIRLPOOLCORPORATIONMAJORAPPLIANCEWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter Whirlpool ") will pay for FSP replacement parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if

another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help

can be found by checking the "Assistance or Service" section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,

call 1-800-807-6777. 8/05

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your appliance to

better help you obtain assistance or service if you ever need it=

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label/plate, located on your appliance=

Dea_er _a_e

Address

Phone number

Model number

Serial number

Purchase date

Page is loading ...

Whirlpool GZ5730XR Owner's manual

Brand: Whirlpool

Model: GZ5730XR

Category: Cooker hoods

Type: Owner's manual

Download PDF

report

in other languages

français: Whirlpool GZ5730XR Le manuel du propriétaire

Whirlpool GZ5730XR Owner's manual

Whirlpool GZ5730XR Owner's manual

in other languages

Related papers

Other documents