Philips RQ1187 User manual

Always here to help you

User manual

Register your product and get support at

www.philips.com/welcome

RQ1100

Series

Page is loading ...

6

General description (Fig. 1)

A Shaver

1 Display

2 Shaver on/off button

3 Protection cap

4 RQ11 Shaving unit

B CRP331Trimmer(specictypesonly)

C JetCleanSystem(specictypesonly)

1 Shaver holder

2 ’Cleaning chamber empty’ symbol

3 Cleaning symbol

4 Drying symbol

5 Jet Clean System on/off button

6 Cleaning chamber release button

D Adapter

E Foldable charger

F Cleaning brush

G HQ200Cleaninguid(specictypesonly)

H Pouch(specictypesonly)

The display

Note: If there is a protective foil on the display, remove it before you use the

shaver for the rst time.

The various shaver types have different displays, which are shown in the

guresbelow.

- RQ1180

- RQ1160

- RQ1150

ENGLISH

Charging

- Chargingtakesapprox.1hour.

RQ1180

- Whentheshaverischarging,rstthebottomcharginglightashes,

then the second charging light, and so on until the shaver is fully

charged.

- Quick charge: When the shaver contains enough energy for one shave,

thebottomcharginglightalternatelyashesorangeandwhite.

RQ1160/RQ1150

Note: The displays of the various shaver types look different, but work in the

same way.

- Whentheshaverischarging,rsttheplugsymbolandthebattery

symbolashalternately.Aftersometime,theplugsymbolgoesoutand

thebatterysymbolcontinuestoashuntiltheshaverisfullycharged.

- Quick charge: When the shaver contains enough energy for one shave,

thealternateashingoftheplugsymbolandbatterysymbolstopsand

onlythebatterysymbolashes.

Battery fully charged

RQ1180

- When the battery is fully charged, all charging lights light up

continuously.Afterapprox.30minutes,thedisplayautomatically

switchesoffagain.

RQ1160/RQ1150

Note: The displays of the various shaver types look different, but work in the

same way.

- When the battery is fully charged, the battery symbol lights up

continuously.Afterapprox.30minutes,thedisplayautomatically

switchesoffagain.

Battery low

RQ1180

- When the battery is almost empty (when there are only 5 or fewer

shavingminutesleft),thebottomcharginglightashesorange.

- When you switch off the shaver, the bottom charging light continues to

ashforafewseconds.

RQ1160/RQ1150

Note: The displays of the various shaver types look different, but work in the

same way.

- When the battery is almost empty (when there are only 5 or fewer

shavingminutesleft),theplugsymbolashes.

- Whenyouswitchofftheshaver,theplugsymbolcontinuestoashfor

afewseconds.

ENGLISH 7

Remaining battery capacity

RQ1180

- The remaining battery capacity is indicated by the number of charging

lightsthatareon.

Travel lock

Youcanlocktheshaverwhenyouaregoingtotravel.Thetravellock

preventstheshaverfrombeingswitchedonbyaccident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter the travel lock mode.

, The lock symbol lights up on the display.

Note: The displays of the various shaver types look different, but show the

same symbol.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

, The motor starts running to indicate that the travel lock has been

deactivated.

Theshaverisnowreadyforuseagain.

Note: When you place the shaver in the plugged-in charger or Jet Clean System,

the travel lock is automatically deactivated.

Replace shaving head holder

Note: The displays of the various shaver types look different, but show the

same symbol.

For maximum shaving performance, we advise you to replace the shaving

headholderevery12months.

- To remind you to replace the shaving head holder, the appliance is

equipped with a replacement reminder which is activated automatically

afterapprox.12months.Thereplacementreminderisrepeatedat

9successiveshavesoruntilyouresettheshaver.

Charging

Chargingtakesapprox.1hour.

RQ1180/RQ1160: A fully charged shaver has a shaving time of up to

50minutesor15days.

RQ1150: A fully charged shaver has a shaving time of up to 40 minutes or

12days.

Chargetheshaverbeforeyouuseitforthersttimeandwhenthedisplay

indicates that the battery is almost empty (see section ‘Battery low’ in

chapter‘Thedisplay’).

ENGLISH8

Quick charge

After the shaver has charged for 5 minutes, it contains enough energy for

oneshave.

Charging in the charger

1 Insert the small plug into the charger.

2 Unfold the charger (‘click’).

3 Put the adapter in the wall socket.

4 Put the shaver in the charger (1) and press it backwards until it locks

into place (2).

, The display shows that the shaver is charging (see section ‘Charging’

in chapter ‘The display’).



1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

3 Hold the shaver upside down above the holder with the back of the

shaver pointing towards the holder.

Note: RQ1180 only: when you turn the shaver upside down, the battery

indication on the display is also turned upside down so you can still see to what

level the battery is charged.

4 Place the shaver body in the holder behind the two clips (1) and

press it down until it locks into place (2).

Note: The shaver cannot be placed in the Jet Clean System when the protection

cap is on the shaving unit or when the trimmer is placed on the shaver.

, The display shows that the shaver is charging (see chapter

‘The display’).

ENGLISH 9

Using the shaver

Shaving

Skin adaptation period

Yourrstshavesmaynotbringyoutheresultyouexpectandyourskin

mayevenbecomeslightlyirritated.Thisisnormal.Yourskinandbeardneed

timetoadapttoanynewshavingsystem.

Weadviseyoutoshaveregularly(atleast3timesaweek)foraperiodof

3weekstoallowyourskintoadapttothenewshaver.Duringthisperiod,

use your new electric shaver exclusively and do not use other shaving

methods.Ifyouusedifferentshavingmethods,itismoredifcultforyour

skintoadapttothenewshavingsystem.

1 Press the on/off button once to switch on the shaver.

, RQ1180: The display lights up for a few seconds.

2 Move the shaving heads over your skin in circular movements.

- Donotmakestraightmovements.

3 Press the on/off button once to switch off the shaver.

, RQ1180: The display lights up for a few seconds and then shows the

remaining battery capacity.

Wet shaving

Youcanalsousethisshaveronawetfacewithshavingfoamorshavinggel.

To shave with shaving foam or shaving gel, follow the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure that the shaving unit

glides smoothly over your skin.

4 Press the on/off button once to switch on the shaver.

5 Move the shaving heads over your skin in circular movements.

Note: Rinse the shaver under the tap regularly to ensure that it continues to

glide smoothly over your skin.

6 Dry your face and thoroughly clean the shaver after use (see chapter

‘Cleaning and maintenance’).

Note: Make sure you rinse all foam or shaving gel off the shaver.

ENGLISH10



Youcanusethetrimmertogroomyoursideburnsandmoustache.

1 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

2 Insert the lug of the trimmer into the slot in the top of the shaver

(1). Then press down the trimmer (2) to attach it to the shaver

(‘click’).

3 Press the on/off button once to switch on the trimmer.

, RQ1180: The display lights up for a few seconds.

4 You can now start trimming.

5 Press the on/off button once to switch off the trimmer.

, RQ1180: The display lights up for a few seconds to show the

remaining battery capacity.

6 Pull the trimmer straight off the shaver.

Note: Do not twist the trimming unit while you pull it off the shaver.

7 Insert the lug of the shaving unit into the slot in the top of the shaver

(1). Then press down the shaving unit (2) to attach it to the shaver

(‘click’).

ENGLISH 11

Cleaning and maintenance

Never use scouring pads, abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the shaver, its accessories and the Jet

Clean System (specic types only).

- The best and most hygienic way to clean the shaver is in the Jet Clean

System(specictypesonly).Youcanalsorinsetheshaverunderthetap

orcleanitwiththebrushsupplied.

- Cleantheshaveraftereveryshaveforoptimalshavingperformance.

- Youcancleantheoutsideoftheshaverwithadampcloth.

- Regularcleaningguaranteesbettershavingperformance.

Cleaning the shaving unit

Be careful with hot water. Always check if the water is not too hot,

to prevent your hands from getting burnt.

1 Switch off the shaver. Remove it from the charger or remove it from

the Jet Clean System (specic types only).

2 Rinse the shaving unit under a hot tap for some time.

Note: You can also clean the shaving unit with the cleaning brush supplied.

3 Pull the shaving head holder off the bottom part of the shaving unit

and rinse it under a hot tap for 30 seconds.

Note: You can also clean the shaving head holder with the cleaning brush

supplied.

4 Carefully shake off excess water and let the shaving head holder dry.

Never dry the shaving unit with a towel or tissue, as this may damage the

shaving heads.

5 Reattach the shaving head holder to the bottom part of the shaving

unit (‘click’).

ENGLISH12

Cleaning the shaving unit in the Jet Clean System



TheJetCleanSystemhasanautomaticcleaningprogram.Whenyoupress

the on/off button, the Jet Clean System starts cleaning in this automatic

cleaningprogram.

Preparing the Jet Clean System for use

Fillthecleaningchamberbeforerstuse.

1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

, The holder automatically moves to the highest position.

3 Simultaneously press the release buttons on both sides of the

cleaning chamber (1). Then lift the Jet Clean System off the cleaning

chamber (2).

, The cleaning chamber remains behind.

4 Fill the cleaning chamber with HQ200 cleaning uid to a level

between the two lines.

5 Place the Jet Clean System back onto the cleaning chamber.

Makesurethereleasebuttonsclickbackintoplace.

Using the Jet Clean System

Note: If you use the shaver with shaving foam or shaving gel, we advise you

to rinse it under the hot tap before you clean it in the Jet Clean System. This

guarantees an optimal lifetime for the cleaning uid.

1 Hold the shaver upside down above the holder with the back of the

shaver pointing towards the holder.

2 Place the shaver body in the holder behind the two clips (1) and

press it down until it locks into place (2).

, The display shows that the shaver is charging (see chapter ‘The

display’).

3 Press the on/off button on the Jet Clean System to start the cleaning

program.

, The shaver display stops showing the charging indication.

2

1

ENGLISH 13

, The cleaning light starts to ash and the shaver is automatically

lowered into the cleaning uid.

, The cleaning light ashes throughout the cleaning program,

which takes a few minutes.

, During the rst phase of the cleaning program, the shaver

automatically switches on and off several times and moves up and

down.

, During the second phase of the cleaning program, the shaver is

placed in the drying position, indicated by the ashing drying symbol.

This phase takes approx. 2 hours. The shaver stays in this position

until the end of the program.

, After the cleaning program, the charging indication appears on the

shaver display (see chapter ‘The display’).

Note: If you press the on/off button of the Jet Clean System during the cleaning

program, the program aborts. In this case, the cleaning or drying light stops

ashing and the holder moves to the highest position.

Note: If you remove the adapter from the wall socket during the cleaning

program, the program aborts. The holder remains in its current position. When

you put the adapter back into the wall socket, the holder moves to the highest

position.

- Whenthecleaninguiddropsbelowtheminimumlevel,the‘cleaning

chamberempty’symbolstartstoashandtheholderreturnstoits

startingposition.

- IfyouusetheJetCleanSystemtocleanyourshavereveryday,you

needtorellthecleaningchamberapprox.every15days.

Cleaning the Jet Clean System

Cleanthecleaningchamberevery15days.

YoucanwipetheoutsideoftheJetCleanSystemwithadampcloth.

1 Simultaneously press the release buttons on both sides of the Jet

Clean System (1). Then lift the Jet Clean System off the cleaning

chamber (2).

, The cleaning chamber remains behind.

2 Pour any remaining cleaning uid out of the cleaning chamber.

Youcansimplypourthecleaninguiddownthesink.

3 Rinse the cleaning chamber under the tap.

The cleaning chamber is not dishwasher-proof.

4 Fill the cleaning chamber with HQ200 cleaning uid to a level

between the two lines.

5 Place the Jet Clean System back onto the cleaning chamber.

Makesurethereleasebuttonsclickbackintoplace.

ENGLISH14

Extra-thorough cleaning method

Make sure the appliance is switched off.

1 Pull the shaving head holder off the bottom part of the shaving unit.

2 Slide the green retaining frame in the direction of the arrows

indicated on the retaining frame.

3 Lift the retaining frame out of the shaving head holder.

4 Remove the cutter from the shaving guard.

Note: Do not clean more than one cutter and shaving guard at a time, since

they are all matching sets. If you accidentally put a cutter in the wrong shaving

guard, it may take several weeks before optimal shaving performance is

restored.

5 Clean the cutter with the cleaning brush supplied.

ENGLISH 15

6 Clean the inside of the shaving guard.

7 After cleaning, place the cutter back into the shaving guard with the

cutter legs pointing downwards.

8 Place the retaining frame back onto the shaving head holder.

9 Slide the guard back into place (‘click’).

10 Reattach the shaving head holder to the bottom part of

the shaving unit.

ENGLISH16

Cleaning the trimmer

Cleanthetrimmereverytimeyouhaveusedit.

1 Switch on the appliance with the trimmer attached.

2 Rinse the trimmer under a hot tap for some time.

3 After cleaning, switch off the appliance.

Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop

of sewing machine oil every six months.

Replacement

For maximum shaving performance, we advise you to replace the shaving

headholderevery12months.

Only replace the shaving head holder with an original RQ11 Philips

Shaving Head Holder.

Replacement reminder

To remind you to replace the shaving head holder, the appliance is

equipped with a replacement reminder which is activated automatically

afterapprox.12months.Thereplacementreminderisrepeatedat

9successiveshavesoruntilyouresettheshaver.

1 The shaving unit symbol ashes when you switch off the shaver.

Note: The displays of the various shaver types look different, but show the

same symbol.

2 Pull the shaving head holder off the bottom part of the shaving unit.

3 Attach the new shaving head holder to the bottom part of the

shaving unit (‘click’).

4 To reset the shaver, press and hold the on/off button for approx.

10 seconds.

Note: If you do not reset the shaver at the rst replacement reminder,

it continues to show the shaving unit symbol at 8 more shaves or until

you reset the shaver.

ENGLISH 17

Page is loading ...

Philips RQ1187 User manual

Philips RQ1187 User manual

in other languages

Related papers

Other documents