RIDGID WD7000 User manual

Brand: RIDGID

Model: WD7000

Category: Vacuum cleaners

Type: User manual

WD7000

SMAR

CAR

11 U.S. GALLONS/41 LITERS

SMARTCART WET/DRY VAC

FOR QUESTIONS OR INFORMATION CONTACT US AT

CALL 1-800-4-RIDGID (1-800-474-3443) OR

www.ridgidvacs.com

Part No. SP6659 Printed in Mexico

OPERATOR’S MANUAL

SAVE THIS MANUAL FOR FUTURE REFERENCE

Thank you for buying a RIDGID product.

WARNING:

To reduce the risk of injury, the user must read and understand the owner’s manual

before using this product.

• Español - página 19

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 1

Table of Contents

Section Page

Important Safety Instructions. . . . . . . . . . . . . 2

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking and Checking

Carton Contents . . . . . . . . . . . . . . . . . . . . . 5

Removing/Installing/Storing

The Metal Handle . . . . . . . . . . . . . . . . . . . . 6

Filter Removal and Installation . . . . . . . . . . . 7

Wet/Dry Vac Assembly . . . . . . . . . . . . . . . . . 8

Dust Drum Assembly . . . . . . . . . . . . . . . . . 8

Insert Hose . . . . . . . . . . . . . . . . . . . . . . . . . 8

Wheel Assembly . . . . . . . . . . . . . . . . . . . . . . 9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Vacuuming Dry Materials . . . . . . . . . . . . . 11

Vacuuming Liquids . . . . . . . . . . . . . . . . . . 11

Emptying the Drum. . . . . . . . . . . . . . . . . . 11

Moving the Wet/Dry Vac . . . . . . . . . . . . . . 12

Section Page

Blowing Feature . . . . . . . . . . . . . . . . . . . . 12

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Hose Storage . . . . . . . . . . . . . . . . . . . . . . 13

Accessory Storage . . . . . . . . . . . . . . . . . . 13

Cord Wrap . . . . . . . . . . . . . . . . . . . . . . . . 13

Handle Storage. . . . . . . . . . . . . . . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 14

Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Cleaning & Disinfecting

the Wet/Dry Vac. . . . . . . . . . . . . . . . . . . 15

Casters & Wheels. . . . . . . . . . . . . . . . . . . 15

Frame & Handles . . . . . . . . . . . . . . . . . . . 15

Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . 16

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of using common

sense, staying alert, and knowing how your

Wet/Dry Vacuum cleaner (“Vac”) works.

Safety Signal Words

DANGER: Indicates a hazardous

situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a hazardous

situation which, if not avoided, could

result in minor or moderate injury.

When using your Vac, always follow basic

safety precautions including the following:

WARNING

- To reduce the risk of fire, electric

shock, or injury:

•

Read and understand this manual and

all labels on the Wet/Dry Vac before

operating.

•

Use only as descr

ibed in this man

ual.

• Do not leave Vac running while

unattended - you may fail to notice

important signs indicating abnormal

operation such as loss of suction,

debris/liquid exiting exhaust, or

abnormal motor noises. Immediately

stop using Vac if y

ou notice these signs

• Do not leave Vac when plugged in.

Unplug from outlet when not in use and

before servicing.

• Sparks inside the motor can ignite

flammable vapors or dust. To reduce the

risk of fire or explosion, do not use near

combustible liquids, gases, or dusts,

such as gasoline or other fuels, lighter

fluid, cleaners, oil-based paints, natural

gas, coal dust, magnesium dust, grain

dust, aluminum dust, or gun powder.

• Do not vacuum anything that is burning

or smoking, such as cigarettes,

matches, or hot ashes.

• Do not vacuum drywall dust, cold

fireplace ash, or other fine dusts with

standard filter. These may pass through

the filter and be exhausted back into the

air. Use a fine dust filter instead.

• To reduce the risk of inhaling toxic

vapors, do not vacuum or use near toxic

or hazardous materials.

• To reduce the risk of electric shock, do

not expose to rain or allow liquid to enter

motor compartment. Store indoors.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

•

Turn off Vac before unplugging.

• Do not use with a torn filter or without

filter installed except when vacuuming

liquids as descr

ibed in this man

ual.

y debr

is ingested by the impeller may

damage the motor or be e

xhausted into

the air.

• To reduce the risk of injury from

accidental starting, unplug power cord

before changing or cleaning filter.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 2

- Direct air discharge only at work

area.

Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except

blowing dirt and debris.

- Do not use as a sprayer.

- Wear safety eyewear.

• To reduce the risk of being struck by, or

pulled down by, a rolling Vac, lock the

casters when using on any uneven or

sloped surface.

• To reduce the risk of eye injury, wear

safety eyewear. The operation of any

utility Vac or blower can result in foreign

objects being blown into the eyes, which

can result in severe eye damage.

•

Do not unplug by pulling on cord. To

nplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or

other parts. If your Vac is not working as

it should, has missing parts, has been

dropped, damaged, left outdoors, or

dropped into water, call customer

service.

• Do not pull or carry by cord, use cord as

handle, close a door on cord, or pull

cord around sharp edges or corners.

Do not run Vac over cord. Keep cord

away from heated surfaces.

• Do not handle plug, switch, or the Vac

with wet hands.

• Use only extension cords that are rated

for outdoor use. Extension cords in poor

condition or too small in wire size can

pose fire and shock hazards. To reduce

the risk of these hazards, be sure the

cord is in good condition and that liquid

does not contact the connection. Do not

use an extension cord with conductors

smaller than 16 gauge (AWG) in size.

To reduce power loss, use a 14 gauge

extension cord if 25 to 50 ft. long and

12 gauge for 50 ft. or longer.

• This Vac is double-insulated, eliminating

the need for a separate grounding

system. Use only identical replacement

parts. Read the instructions for Servicing

Double-Insulated Wet/Dry Vacs.

• Do not put any object into ventilation

openings. Do not vacuum with any

ventilation openings blocked; keep free

of dust, lint, hair or anything that may

reduce air flow.

• Keep hair, loose clothing, fingers, and all

parts of body away from openings and

moving parts.

• To reduce the risk of falls, use extra care

when cleaning on stairs.

• To reduce the risk of back injury or falls,

do not lift a

Vac that is heavy with liquid

or debr

is. Partially empty by scooping

debris or draining liquid.

• To reduce the risk of personal injury or

damage to Vac, use only Ridgid

recommended accessories.

• When using as a blower:

Observe the following warnings that

appear on the motor housing of your Vac:

WARNING: For your own safety,

read and under

stand o

wner’s

manual. Do not run unattended.

Do not pic

k up hot ashes, coals,

toxic, flammable or other hazardous

materials. Do not use around

explosive liquids or vapors.

ARNING:

o reduce the risk of

electric shoc

k - do not e

xpose to

rain - store indoors.

DOUBLE INSULATED

GROUNDING NOT REQUIRED.

WHEN SERVICING USE ONLY

IDENTICAL REPLACEMENT PARTS.

CAUTION:

• To reduce the risk of hearing damage,

wear ear protectors when using for

extended time or in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the

relative humidity of the air is low.

Vacuuming fine debris with your Vac can

deposit static charge on the hose or

Vac. To reduce the frequency of static

shocks in your home or when using this

Vac, add moisture to the air with a

humidifier.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 3

Introduction

This SMARTCART Wet/Dry Vac is

intended for household use. It may be

used for vacuuming wet or dry media and

may be used as a blower.

Read this operator’s manual to familiarize

yourself with the product features and to

understand the specific usage of your

new Vac.

WARNING: To reduce the risk of

electric shock, always install float

before any wet pick-up operation.

ARNING: 50 Lb. weight limit.

Do not stand or sit on Vac. Improper

use may cause injury.

ARNING: To reduce the risk of

fire or other damage, do not use

onboard storage compartments to

store oily rags or containers with

flammable, explosive, corrosive or

toxic materials.

WARNING: To reduce the risk of

fire or electric shock, do not leave

Vac plugged in when not in use.

Do not leave Vac running while

unattended.

SAVE THIS MANUAL

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 4

Unpacking and Checking Carton Contents

Refer to the assembly sketch for

positioning of parts.

Remove contents of carton. Check each

item against the Carton Contents List.

Call 1-800-4-RIDGID (1-800-474-3443) or

E-mail us at inf[email protected] if any parts

are damaged or missing.

9/16” Socket & Ratchet

Tools Required

Mallet9/16” Wrench

Carton Contents List

Key Description Qty

A Wet/Dry Vac Assembly.................1

B* Qwik-Lock™ Fine Dust Filter.......1

C* Filter Support Assembly...............1

D Hose Assembly............................1

E Utility Nozzle ................................1

F Wet Nozzle...................................1

G Crevice Nozzle.............................1

H Claw Nozzle.................................1

J Dusting Brush ..............................1

K Extension Handle.........................2

L 8” Wheel.......................................2

M Metal Handle................................1

N Operator’s Manual........................1

Bag of Loose Parts “A”:

O 3” Caster ......................................2

P Wheel Hub Adapter .....................2

Q Wheel Caps .................................2

Bag of Loose Parts “B”:

3/8” x 4” Bolt.................................2

3/8” x 1-1/2” Spacer .....................2

am Nut........................................2

U Lock Washer ................................2

V Flat Washer..................................6

W Locknut.........................................2

* These items may come preassembled.

If they are not present in the car

ton,

check inside the drum to see if they are

preassembled.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 5

Removing/Installing/Storing

The Metal Handle

Your metal handle comes packaged in

the dust drum. You must remove the

metal handle from the dust drum and

install the handle in the correct direction,

bent area facing away from the back of

the Vac, before continuing. (Also remove

the 8” wheel and set aside for

installation).

Installing Handle

Press and hold release buttons while

installing handle into handle receptacles

in drum (See illustration).

NOTE: An audible snap of release

buttons indicates successful engagement

of handle.

Lowering Handle for Storage

To store Wet/Dry Vac, press and hold

release buttons while firmly sliding handle

down.

Removing Handle

Press and hold release buttons, as

shown. While firmly pushing in release

buttons, pull handle upwards to remove.

Press and

Hold Release

Buttons

Handle

Receptacle (2)

Release

Button (2)

Handle

SMAR

CAR

Pull Down and

Slide Dust Drum

Out of Wet/Dry

Vac Unit

Latch (2)

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 6

NOTE: The filter is accessed by

unlatching and removing the dust drum.

The filter support assembly can be

removed by grasping the filter support as

shown in the illustrations below.

Filter Removal and Installation

WARNING: For your own safety,

never connect plug to power source

outlet until all assembly steps are

complete and you have read and

understood the safety and operation

instructions. Do not operate Vac

with any parts damaged or missing.

Filter

Support

THIS SIDE

OWARDS LID

Open End

of Float

Qwik Lock™

Stud

Filter

abs (2)

Integrated Filter

Plate with Center

ole

USH

DOWN

PULL

Rubber

Gasket at

Bottom of

Filter

(

cutaway

view)

SMAR

CAR

Pull Down and

Slide Dust Drum

Out of Wet/Dry

Vac Unit

Latch (2)

Dust

Drum

Filter Support

Assembly

Removal and Installation

of the Qwik Lock™ Filter

Filter Removal:

Hold the filter tabs of the Qwik Loc

™

filter in each hand.

2. With one thumb on the Qwik Lock™

stud, which protr

udes through the

integrated filter plate

, lift up on the

filter tabs while pushing down on the

stud.

NOTE: Failure to properly seat the

bottom gasket could result in debris

bypassing the filter.

3. This action will cause the filter to

release from the filter cage. Slide filter

off cage.

Filter Installation:

Carefully slide the Qwik Lock™ filter

over the filter cage and press down on

the outside edge of the filter until the

rubber gasket on the bottom of the

filter seats securely around the base

of the filter cage and against the lid.

2. Align the small center hole in the top

of the filter over the Qwik Lock™ stud

on the filter cage. Press firmly on top

of the filter near the stud to allo

w the

filter to snap over the ball on the end

of the stud. The filter is now attached.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 7

Wet/Dry Vac Assembly

WARNING: To avoid ingesting

debris or water in the impeller and

damaging Vac, never operate

without filter support assembly in

place.

SMAR

CAR

ull Down and

lide Dust Drum

ut of Wet/Dry

Vac Unit

Dust Drum

Wet/Dry

Vac Unit

Slot

Dust Drum Wheel

Latch

Holder

Latch Unlocked

Latch Locked

Dust Drum Assembly

1. Slide the dust drum into the front of the

wet/dry Vac unit when filter assembly is

complete. Position the dust drum

wheels into the drum area slots and

glide into place.

NOTE: When reinstalling the dust drum

and filter support assembly, ensure that

the front of the dust drum is flush with the

lid and motor cover assembly. The dust

drum should fit snugly into place. There

are two pins in the Wet/Dry Vac unit that

must fit into the slots in the drum. This

ensures proper alignment. The dust drum

must be installed properly to ensure the

Wet/Dry Vac functions correctly.

2. Pull the two latches on the front of the

dust drum up and over the latch

holders and press down firmly until

they snap in place. If the pins from the

lid and motor cover assembly are not

aligned, the latches will not lock.

Insert Hose

Insert the push button end of the hose

assembly into the inlet of the Vac. The

hose should snap into place. To remove

the hose from the Vac, press the release

button in the hose assembly and pull the

hose out of the Vac inlet, as shown.

SMAR

CAR

Push

Button

Inlet

Hose

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 8

Jam Nut

Lock Washer

Flat Washer

3/8" Bolt

Flat Washer

3/8" Bolt

Jam Nut

8" Wheel

Wheel Hub

Adapter

Wheel Ribs

Wheel Hub

Adapter Slots

Wheel

Lock

8" Wheel

Spacer

Flat Washer

Locknut

Wheel Cap

Locknut

Wheel Assembly

f any parts are missing or damage,

contact customer service. Do not attempt

to assemble unit until you have all the

parts.

1. Pull the dust drum clear of the

Wet/Dry Vac. Locate the two 8”

diameter wheels and the two bag

assemblies.

2. Prop a 2 x 4 wood block

approximately 12” long, under the

rear of the Vac.

3. Place one flat washer onto the 3/8”

bolt and install into the hole in rear

panel. Push the bolt all the way

through wheel hub.

4. Place one flat washer and one lock

washer onto the bolt.

5. Screw on one jam nut and tighten

with a 9/16” wrench. You will need to

hold the head of the bolt with the

9/16” socket to securely tighten the

jam nut.

6. Insert the wheel hub adapter onto the

8” wheel. Make sure that the slots on

the wheel adapter fits snugly into the

ribs of the wheel. Place adapter and

wheel onto bolt.

7. Insert one spacer on the bolt and

push through the wheel opening.

8. Install one flat washer and one

locknut. Tighten locknut securely.

9. Using a rubber mallet, gently tap the

wheel caps onto each wheel. This is

required on both the left and right

sides

10.

Lock the rear wheels by stepping

down on the wheel locks to secure

unit. Tilt Vac back to expose the front

wheel area.

2 x 4 Wood Block

Back of Vac

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 9

Caster Stem

Socket

Caster Ball

Caster

Operation

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will fit

in a polarized outlet only one way. If the

plug does not fit fully in the outlet, reverse

the plug.

If it still does not fit, contact a

qualified electrician to install the proper

outlet.

Do not change the plug in any way.

After you plug the power cord into the

Familiarize yourself with the accessories

included with the Vac. Each accessory may

be used in v

ious ways for vacuuming and

wing debr

Here is a list of the

accessories and their uses.

OFF

1. Push the caster on until the ball on

the caster stem is inserted all the way

onto the socket. You will hear the ball

snap into the socket and the caster

will swivel easily when positioned

correctly.

outlet, turn the unit on by pushing the

switch from position "O" to position "l". The

symbols used on the switch actuator are

international "On & Off" symbols.

SMAR

CAR

Utility Nozzle - Gener

al pur

pose nozzle for

most vacuuming applications.

WARNING: To reduce the risk of fire, explosion, or damage to Vac:

• Do not leave Vac running while unattended - you may fail to notice important signs

indicating abnormal operation such as loss of suction, debris/liquid exiting the

exhaust, or abnormal motor noises. Immediately stop using Vac if you notice these

signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off suction.

• Sparks inside the motor can ignite airborne flammables. Do not operate Vac near

flammable liquids or in areas with flammable gases, vapors, or explosive/airborne

dust. Flammable liquids, gases, and vapors include: lighter fluid, solvent-type

cleaners, oil-based paints, gasoline, alcohol, and aerosol sprays. Explosive dusts

include: coal, magnesium, aluminum, grain, and gun powder.

• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.

WARNING: To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter motor compartment. Store indoors.

• Do not handle plug, switch, or Vac with wet hands.

• Unplug Vac before servicing. If your Vac is not working as it should, has missing

parts, has been dropped, damaged, left outdoors, or dropped into water, return it to an

independent service center or call customer service.

• When using an extension cord, use only outdoor-rated cords that are in good

condition. Do not allow the connection to come into contact with liquid.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 10

1. The Vac comes equipped with a drain

for easy emptying of liquids. Simply

unscrew the drain cap and lift the

opposite side slightly to empty the

drum.

2. Another option is to remove the drum

from the Vac.

3. Pull the drum out from the Vac by

pulling down and sliding the drum on

the axle support under the drum.

Dump the dr

um contents into the

proper waste disposal container.

WARNING: To reduce the risk of

injury from accidental starting,

unplug power cord before emptying

the drum.

WARNING: To reduce the risk of

back injury or falls, do not lift a Vac

heavy with liquid or debris. Scoop

or drain enough contents out to

make the Vac light enough to lift

comfortably.

Emptying the Drum

Hose - Provides transfer of vacuum or

blowing capability to work site. Provides

the means of attaching extension handles

and nozzles.

Crevice Tool - Use to pick up debris in

hard to reach locations.

Vacuuming Dry Materials

1. The filter must always be in correct

position to reduce the risk of leaks and

possible damage to Vac.

2. Your Wet/Dry Vac comes with the

VF5000 Filter installed. When using

your Vac to pick up very fine dust, it will

be necessary for you to empty the

drum and clean the filter at more

frequent intervals to maintain peak Vac

performance.

NOTE: A dry filter is necessary to pick up

dry material. If you use your Vac to pick

up dust when the filter is wet, the filter will

clog quickly and be very difficult to clean.

acuuming Liquids

1. When picking up small amounts of

liquid the filter ma

y be left in place

2. When picking up large amounts of

liquid we recommend that the filter be

removed. If the filter is not remo

ved, it

will become satur

ated and misting ma

appear in the exhaust.

WARNING: To reduce the risk of

fire or electric shock, do not run Vac

unattended.

3. When the liquid in the drum reaches a

redetermined level, the float

mechanism will rise automatically to cut

off air-flow. When this happens, turn off

the Vac, unplug the power cord, and

empty the drum. You will know that the

float has risen because Vac airflow

ceases and the motor noise will become

higher in pitch, due to increased motor

speed.

4. After using the Vac to pick up liquids,

allow the filter to dry to reduce the risk of

mildew and damage to the filter.

IMPORTANT: To reduce the risk of

damage to the Vac do not run motor with

float in raised position.

Wet Nozzle - Used for wet pickup on

mooth surfaces to pick up liquid and dry

the surface in one stroke.

Claw Nozzle - Used for wet or dry pickup.

Dusting Brush - Dry pickup of dust and

dirt debris.

Car Nozzle (not provided) - Dry pickup

nozzle for car interiors and most

upholstery cleaning.

Extension Handles - These handles can

be connected together and provides

additional length for more reach.

Operation (continued)

WARNING: Do not operate with

the float removed. It prevents liquid

from entering the impeller and

damaging the motor.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 11

Pull Up to Unlock

Wheel Locks

Blowing Port

5. Replace the drum by reinserting into

the cavity and push until it snaps into

place.

Moving the Wet/Dry Vac

To maneuver the Vac, the metal handle in

the rear of the unit should be positioned

in the upright position for ease of

movement. Be sure to unlock the back

wheels by pulling up on the wheel locks

before moving the Vac.

Blowing Feature

Your Vac features a blowing port. It can

blow sawdust and other debris. Follow the

steps below to use your Vac as a blower.

1. Locate blowing port of your Vac.

WARNING: Always wear safety

eyewear complying with ANSI Z87.1

(or in Canada, CSA Z94.3) before

using as a blower.

CAUTION: Wear a dust mask if

blowing creates dust which might

be inhaled.

UTION:

To reduce the risk of

hearing damage wear ear protectors

when using the Vac/blower for

extended hours or when using in a

noisy area.

WARNING: To reduce the risk of

injury to bystanders, keep them

clear of blowing debris.

Locking End

Hose

Assembly

Operation (continued)

Inser

t the locking end of the hose

assembly into the blowing port of the

Vac. The hose should snap into place.

To remove the hose from the Vac,

press the release button in the hose

assemb

ly and pull the hose out of the

Vac inlet.

3. (Optional) Attach extension handle to

opposite end of hose

, then place the

cre

vice tool on the w

and.

4. Turn Vac on and you are ready to use

our

ac as a b

wer.

Axle

Support

Dust

Drum

Drain

Pull Down and

Slide Dust Drum

Out of Wet/Dry

Vac Unit

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 12

Hose Storage

The hose may be stored by placing in the

top removable tray.You may also open the

hinged top to access the hose storage.

Accessory Stora

Your wet/dry Vac accessories may be stored

in the removable lower tray. Cleaning

supplies may be stored in the storage area

on the back of the unit between the wheels.

The extension handles snap into place at

the the back of the Vac in the extension

handle storage areas.

Storage

Hose Storage Tray

Hinged Top Access

to Hose Storage

Accessory

Storage Tray

Cleaning

Storage

Area

Cord Wrap Area

Cleaning

Supplies

Extension Handle

Storage

Cord Wrap

hen vacuuming is complete, unplug the

cord and wrap it around the cord wrap

area located on the back of the unit.

Press and

Hold Release

Buttons

While Sliding

Handle

Downward

Handle

Handle Storage

When storing the Wet/Dry Vac, press and

hold release buttons while firmly sliding

handle down.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 13

Maintenance

Filter Cleaning

Your filter should be cleaned often to

maintain peak Vac performance.

Be sure the filter is dry before storing or

picking up dry debris.

IMPORTANT: After cleaning, check the

filter for tears or small holes. Do not use a

filter with holes or tears in it. Even a small

hole can cause a lot of dust to come out

of your Vac. Replace it immediately.

Filter Remo

val

Refer to page 7 “Filter Removal and

Installation” Section of this manual.

IMPORTANT: To avoid damage to the

blower wheel and motor, always reinstall

the filter before using the Vac for dry

material pick-up.

WARNING: To reduce the risk of

injury from accidental starting,

unplug power cord before changing

or cleaning filter.

NOTE:

The filter is made of high quality

paper designed to stop very small

particles of dust. The filter can be used

for dry pick up or small amounts of liquid.

Handle the filter carefully when removing

to clean or installing it. Creases in the

filter pleats may occur from installation

but will not affect the performance of the

filter.

Filter

Cleaning A Dry Filter

1. Some removal of dry debris can be

accomplished without removing the

filter from the Vac. Slap your hand on

top of the lid while the Vac is turned

off.

2. For best cleaning results due to

accumulated dust, clean the filter in an

open area. Cleaning SHOULD be

done outdoors and not in the living

quarters.

3. After filter removal from Vac, remove

the dry debris by gently tapping filter

against the inside wall of your dust

drum. The debris will loosen and fall.

4. For thorough cleaning of dry filter with

fine dust (no debris), run water

through it as described under

"Cleaning A Wet Filter".

Cleaning A Wet Filter

After filter is removed, run water through

the filter from a hose or spigot. Take care

that water pressure from the hose is not

strong enough to damage filter.

Installation

Refer to page 7 "Filter Removal and

Installation" Section of this manual.

Allow the filter to dry before reinstalling

and storing the Vac.

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 14

Cleaning and Disinfecting the

Wet/Dry Vac

To keep your Wet/Dry Vac looking its

best, clean the outside with a cloth

dampened with warm water and mild

soap.

To clean the drum:

1. Dump debris out.

2. Wash drum thoroughly with warm

water and mild soap.

3. Wipe out with dry cloth.

Before prolonged storage or as needed

(i.e.; after waste water pick up) the drum

should be disinfected.

To disinfect the drum:

1. Pour 1 gallon of water and 1 teaspoon

chlorine bleach into the drum.

2. Let solution stand for 20 minutes,

carefully swishing every few minutes,

making sure to wet all inside surfaces

of the drum.

3. Empty drum after 20 minutes. Rinse

with water until bleach smell is gone.

Allow drum to dry completely before

sealing the motor on the drum.

WARNING: To assure product

SAFETY and RELIABILITY, repairs

and adjustments should be

performed by Authorized Service

Centers, always using RIDGID

replacement parts.

Casters and Wheels

Should your cart squeak or become hard

to roll, you should place two or three

drops of general purpose oil on each

wheel at the axle. If your casters are

noisy, you may put a drop of oil on the

roller shaft to make them quieter.

Frame and Handles

Your metal handle is painted to prevent

rust, however, liquids and corrosive

debris should be wiped off with a soft

cloth should they come in contact with

the handle.

Maintenance (continued)

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 15

Key

No. Part No. Description

1 510013 Actuator Assembly

2 832328 Power Head Assembly

3 832119 Filter Support Assembly

4 832120 Handle Assembly

5 832113 Dust Drum Assembly

6 832116 Drum Latch

7 73185 Drain Cap

8 830598 8” Wheel

9 VF5000 Filter, Fine Dust Qwik Lock™

10 VT1789 Utility Nozzle

11 VT2540 Claw Nozzle

12 VT1710 Wet Nozzle

13 829792 Crevice Tool

14 VT1701 Dusting Brush

15 831337-8 Hose Assembly

16 VT1708 Extension, Handle

509950 Bag Assembly (Casters)

18 509949 Bag Assembly (8” Wheel Hardware)

19 SP6659

Oper

ator’

s Manual

WARNING

SERVICING OF DOUBLE-INSULATED WET/DRY VAC

In a double-insulated Wet/Dry Vac, two systems of insulation are provided

instead of grounding. No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added. Servicing a double-

insulated Wet/Dry Vac requires extreme care and knowledge of the system,

and should be done only by qualified service personnel. Replacement parts

for a double-insulated Wet/Dry Vac must be identical to the parts they replace.

Your double-insulated Wet/Dry Vac is marked with the words "DOUBLE

INSULATED" and the symbol (square within a square) may also be

marked on the appliance.

To reduce the risk of injury from electrical shock, unplug power cord before

servicing the electrical parts of the Wet/Dry Vac.

Repair Parts

11 Gallon SMARTCART Wet/Dry Vac

Model Number WD70000

RIDGID parts are available on-line at www.ridgidparts.com

Always order by Part Number - Not by Key Number

† These replacement parts may be available where you purchased your Vac.

†

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 16

IDGID parts are available on-line at www.ridgidparts.com

Repair Parts (continued)

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 17

Part No. SP6659 Form No. SP6659-4 Printed in Mexico 06/12

• What is covered

RIDGID® Wet/Dry Vacs are warranted to be free of defects in workmanship and material.

• How long coverage lasts

This warranty lasts for the lifetime of the RIDGID® tool. Warranty coverage ends when the product

becomes unusable for reasons other than defects in workmanship or material.

• How to obtain service

To obtain the benefit of this warranty, please call 1-800-4-RIDGID (1-800-474-3443).

• What we will do to correct problems

Warranted Wet/Dry Vacs will be repaired or replaced, at Ridge Tool Company's option, and returned

at no charge; or, if after three attempts to repair or replace during the warranty period the Wet/Dry

Vac is still defective, you can elect to receive a full refund of your purchase price.

• What is not covered

Failures due to misuse, abuse or normal wear and tear are not covered by this warranty. RIDGE

TOOL COMPANY SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

• How local laws relate to the warranty

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you. This warranty gives you specific rights, and you

may also have other rights which vary from state to state, province to province, or country to

country.

• No other express warranty applies

This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID® Wet/Dry Vacs.

No employee, agent, dealer, or other person is authorized to alter this warranty or make any other

warranty on behalf of Ridge Tool Company.

QUESTIONS OR COMMENTS? CALL

1-800-4-RIDGID (1-800-474-3443)

www.ridgidvacs.com

Please ha

ve your Model Number and Serial Number on hand when calling.

Stock No. WD7000

Model No. WD70000

Serial Number

Model and serial numbers may be found on the rear panel. You should record both

model and serial numbers in a safe place for future use.

c 2012 Emerson

SP6659-4 WD7000 ES 6/12/12 8:44 AM Page 18

Page is loading ...

RIDGID WD7000 User manual

Brand: RIDGID

Model: WD7000

Category: Vacuum cleaners

Type: User manual

Download PDF

report

in other languages

français: RIDGID WD7000 Manuel utilisateur
español: RIDGID WD7000 Manual de usuario

RIDGID WD7000 User manual

RIDGID WD7000 User manual

in other languages

Related papers

Other documents