U-Bolts (2 ea.)
Damper Blade with
Weights (1 ea.)
Damper
Weights
Location
Damper
Blade Cover
(1 ea.)
U-Bolt Nuts (4 ea.) U-Bolt Spacer
Block (2 ea.)
Parts Included With Kit:
Part No. Description Qty.
800193-01 Assembly, Damper Blade 1
900802-00 Installation Instruction 1
This kit provides components that are designed to repair the damper
installed on the appliance.
If you encounter any problems, need clarification of these instruc-
tions or are not qualified to properly install this kit, contact you local
distributor or dealer.
Read this instruction sheet in its entirety before beginning the
installation.
FOLLOW ALL WARNINGS AND PRECAUTIONS IN THE INSTRUC-
TION SHEET.
TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
Damper Blade Repair Kit
Model DBRK-C36 (F3162)
Installation Instructions
For use with:
Astria Craftsman36, Tuscan36 series
Superior WCT/WRT3036/WRE3036 Series
Comfort Flame Columbus36 Series
For more information, visit IHP.US.com
P/N 900802-00 Rev. NC 09/2016
Figure 1 - Assembly, Damper Blade
2
Figure 4 - Placing the U-Bolts (Front of Fireplace)
DAMPER PLATE REMOVAL
1. Remove the existing damper plate from the rod by grinding off
the 3 welds. A disc grinder is recommended or a small Dremel
tool with a small diameter disc might be best in case the end
welds are close to the damper can walls (see Figure 2).
NOTE: Be careful not to damage the damper can walls and
the rod as it will remain in place to be used with the new
damper blade.
2. Grind welds off of rod as best and as much as possible. Be careful
not to damage or grind into the rod (see Figure 3).
ROTATION
Figure 2 - Removing Welds
Figure 3 - Rod with Welds Removed
Damper
Welds
INSTALLING THE NEW BLADE
NOTICE: FOR EASIER INSTALLATION ANOTHER
PERSON IS RECOMMENDED.
1. Holding the damper blade with the weights facing the right side
of the fireplace (if standing in front of it), wiggle it up against
the rod as shown (see Figure 4).
NOTE: MAKE SURE THE 3 SQUARE CUT OUTS CLEAR ANY
WELD TAGS LEFT BEHIND ON THE ROD.
2. While holding the new damper blade up against the rod, insert
the 2 U-bolts from the opposite side of the weights (see Figure 4).
3. Holding the U-bolts in place install the cover plate over the U-
bolts then secure it with the spacer block, lock washers and nuts.
Hand tighten the nuts only at this point (see Figure 5, page 3).
3
TIGHTENING THE BLADE
Note: In the previous step the U-bolt nuts were only hand tightened.
1. Now lock open the damper blade by sliding and locking the
damper rod handle to the far left (see Figure 7). NOTE: PULL
THE DAMPER ROD FAR ENOUGH FORWARD SO THAT THE ROD
CLEARS THE "LOCKING CORNER" (see Figure 8). The damper
blade should be at a vertical position now. While holding it in
this position, center the damper blade on the damper can and
torque the 4 nuts tight.
2. Finally do a test trial. Close the damper by sliding the handle
to the far right and observe that the rod does not spin on the
U-bolts. If it does you will need to tighten the nuts further.
Figure 5- Installing the Damper Blade
Figure 6- Securing the Damper Blade
Figure 8- Locking Corner
Figure 7- Test Trial (Showing Damper Rod Handle in the Open
Position)
Figure 9- Damper in Fully Locked Position
Spacer
Block
NOTICE: IF THE DAMPER BLADE DOES NOT FULLY
CLOSE IN THE LOCKED POSITION, THE BLADE MUST
BE CENTERED. UNTIGHTEN THE BOLT NUTS AND
SLIGHTLY ADJUST THE BLADE FROM LEFT TO RIGHT
OR FRONT TO BACK.
OPEN
Locking
Corner
Innovative Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2016 Innovative Hearth Products LLC
P/N 900802-00 Rev. NC 09/2016 1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
-
1
-
2
-
3
-
4
Astria Fireplaces WRE30 Instruction Sheet
- Type
- Instruction Sheet
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Breckwell P23FSL User manual
-
-
-
-
Vogelzang International VG5770 Owner's manual
-
Breckwell Cardinal P24I User manual
-
-
-
-
New Buck Corporation FP 91 User manual
