Astria Fireplaces Tuscan Instruction Sheet

Brand: Astria Fireplaces

Model: Tuscan

Type: Instruction Sheet

This manual is also suitable for

Astria Fireplaces Tuscan fireplaces offer a range of features to enhance your home heating experience. These fireplaces are designed for easy installation and come with a damper blade repair kit, allowing you to maintain optimal airflow and efficiency. With various models available, including the Craftsman36 and Columbus36 series, you can choose the perfect fireplace to suit your needs and style.

U-Bolts (2 ea.)

Damper Blade with

Weights (1 ea.)

Damper

Weights

Location

Damper

Blade Cover

(1 ea.)

U-Bolt Nuts (4 ea.) U-Bolt Spacer

Block (2 ea.)

Parts Included With Kit:

Part No. Description Qty.

800193-01 Assembly, Damper Blade 1

900802-00 Installation Instruction 1

This kit provides components that are designed to repair the damper

installed on the appliance.

If you encounter any problems, need clariﬁcation of these instruc-

tions or are not qualiﬁed to properly install this kit, contact you local

distributor or dealer.

Read this instruction sheet in its entirety before beginning the

installation.

FOLLOW ALL WARNINGS AND PRECAUTIONS IN THE INSTRUC-

TION SHEET.

TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL

BEFORE PROCEEDING.

Damper Blade Repair Kit

Model DBRK-C36 (F3162)

Installation Instructions

For use with:

Astria Craftsman36, Tuscan36 series

Superior WCT/WRT3036/WRE3036 Series

Comfort Flame Columbus36 Series

For more information, visit IHP.US.com

P/N 900802-00 Rev. NC 09/2016

Figure 1 - Assembly, Damper Blade

Figure 4 - Placing the U-Bolts (Front of Fireplace)

DAMPER PLATE REMOVAL

1. Remove the existing damper plate from the rod by grinding off

the 3 welds. A disc grinder is recommended or a small Dremel

tool with a small diameter disc might be best in case the end

welds are close to the damper can walls (see Figure 2).

NOTE: Be careful not to damage the damper can walls and

the rod as it will remain in place to be used with the new

damper blade.

2. Grind welds off of rod as best and as much as possible. Be careful

not to damage or grind into the rod (see Figure 3).

ROTATION

Figure 2 - Removing Welds

Figure 3 - Rod with Welds Removed

Damper

Welds

INSTALLING THE NEW BLADE

NOTICE: FOR EASIER INSTALLATION ANOTHER

PERSON IS RECOMMENDED.

1. Holding the damper blade with the weights facing the right side

of the ﬁreplace (if standing in front of it), wiggle it up against

the rod as shown (see Figure 4).

NOTE: MAKE SURE THE 3 SQUARE CUT OUTS CLEAR ANY

WELD TAGS LEFT BEHIND ON THE ROD.

2. While holding the new damper blade up against the rod, insert

the 2 U-bolts from the opposite side of the weights (see Figure 4).

3. Holding the U-bolts in place install the cover plate over the U-

bolts then secure it with the spacer block, lock washers and nuts.

Hand tighten the nuts only at this point (see Figure 5, page 3).



TIGHTENING THE BLADE

Note: In the previous step the U-bolt nuts were only hand tightened.

1. Now lock open the damper blade by sliding and locking the

damper rod handle to the far left (see Figure 7). NOTE: PULL

THE DAMPER ROD FAR ENOUGH FORWARD SO THAT THE ROD

CLEARS THE "LOCKING CORNER" (see Figure 8). The damper

blade should be at a vertical position now. While holding it in

this position, center the damper blade on the damper can and

torque the 4 nuts tight.

2. Finally do a test trial. Close the damper by sliding the handle

to the far right and observe that the rod does not spin on the

U-bolts. If it does you will need to tighten the nuts further.

Figure 5- Installing the Damper Blade

Figure 6- Securing the Damper Blade

Figure 8- Locking Corner

Figure 7- Test Trial (Showing Damper Rod Handle in the Open

Position)

Figure 9- Damper in Fully Locked Position

Spacer

Block

NOTICE: IF THE DAMPER BLADE DOES NOT FULLY

CLOSE IN THE LOCKED POSITION, THE BLADE MUST

BE CENTERED. UNTIGHTEN THE BOLT NUTS AND

SLIGHTLY ADJUST THE BLADE FROM LEFT TO RIGHT

OR FRONT TO BACK.

OPEN

Locking

Corner

Innovative Hearth Products reserves the right to make changes at any time, without notice, in

design, materials, speciﬁcations, prices and also to discontinue colors, styles and products.

Consult your local distributor for ﬁreplace code information.

P/N 900802-00 Rev. NC 09/2016 1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

Astria Fireplaces Tuscan Instruction Sheet

Brand: Astria Fireplaces

Model: Tuscan

Type: Instruction Sheet

This manual is also suitable for

Download PDF

report

Astria Fireplaces Tuscan Instruction Sheet

This manual is also suitable for

Astria Fireplaces Tuscan Instruction Sheet

Related papers

Other documents