1
GAS LOG SETS
P/N 900935-00
Rev. NC, 10/2018
HEARTH PRODUCTS
KITS AND ACCESSORIES
KIT CONTENTS
1 ea. Log Set
1 ea. Instruction Sheet
GAS LOG PLACEMENT GUIDE FOR INSTALLING GAS LOG SETS
[For Use With Aries35, DRT2035, Bellevue 32, and DRI2032 Series Direct-Vent Gas Fireplaces/Inserts]
GENERAL INFORMATION
This log placement guide has been prepared to present detailed log placement
illustrations and provide instruction to assist in the setup of replacement
logs and after the annual cleaning and inspection cycles. The information
provided here is to be used in conjunction with the Installation and Operation
Instructions provided with the appliance.
If you encounter any problems, need clarification of these instructions or are
not qualified to properly install this kit, contact your local distributor or dealer.
Read this instruction sheet in its entirety before beginning the installation.
DO NOT attempt to install the logs until the appliance installation has been
completed, the gas line connected and tested for leaks and the initial burner
operation has been checked out.
The logs have notches/tabs/pins to assist proper positioning. Proper log
placement is critical to prevent sooting. Place the logs in the gaps between
flame peaks, so they do not impinge the flames. Follow the log placement
instructions precisely.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OPERA-
TION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE
INSTRUCTIONS.
SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
Log Set
I.D.# Description
1Left Rear Log
2Left Front Bottom Log
3Right Front Bottom Log
4Right Rear Log
5Twig Log
1
4
2
3
5
1
4
2
3
5
TOOLS NEEDED
None
INSTALLATION INSTRUCTIONS
Pre-installation Instructions:
1. Allow the fireplace to cool completely before proceeding.
2. Remove the barrier and door (see instructions in the Installation and
Operation Manual provided with the appliance).
3. Remove the old logs that need replacing. Discard old logs.
Install new logs per the following instructions:
1. Locate the placement tabs (Figure 2).
2. Bend up the log placement tabs (Figure 2).
3. Install the rear left log (1) (Figure 3).
Figure 2 - Locate the log placement tabs
Figure 1 - Log Set
Tabs for
Log #1
Tabs for
Log #2
Tabs for
Log #4
Tabs for
Log #3
Figure 3 - Place left rear log (1)
Front View Bottom View
1
Slots fit over Tabs shown in Figure 2
2NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
4. Install left front bottom log (2) on two tabs (Figure 4).
5. Install right front bottom log (3) on two tabs (Figure 5).
Figure 4 - Place left front bottom log (2)
2
Top
View
Bottom
View
Slots fit over Tabs
shown in Figure 2
Figure 5 - Place right front bottom log (3)
Top
View Bottom
View
3
Slots fit over Tabs
shown in Figure 2
6. Install right rear log (4) (Figure 6). This log should be placed as far
to the right as the slot allows.
7. Install the twig log (5) (Figure 7). This log rests on the left rear log
and the grate.
Figure 6 - Place right rear log (4)
4
Slot fit over Tab
shown in Figure 2
Top View Bottom View
Figure 7 - Place twig log (5)
Bottom View
Top View
5
For Fireplace Models
For Insert models
For Fireplace ModelsFor Insert models
3
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
8. Tear the glowing embers into dime size pieces. Place glowing embers as shown in Figure 8.
9. Reinstall glass door and barrier per instructions in the Installation and Operation Manual provided with the appliance.
Figure 8 - Place glowing embers (rockwool)
Do NOT place embers on or close to large
ports or the pilot area as seen here (circled).
Figure 9 - Glass Door
Latch
Glass
Door
NOTE: When installing the glass door, ensure the spacing on both sides is even and equal.
12
INSPECT GASKET AND ADJUST IF NECESSARY (see pictures above)
(1) Ensure the gasket is properly positioned, and area to keep clear, is as shown.
(2) Inspect gasket after installation to ensure it appears as shown above.
Inside view
of glass door
showing
proper gasket
positioning With door installed,
ensure gasket is posi-
tioned as shown.
Gasket
Gasket
SEE WARNING BELOW
WARNING
Reinstall any barrier removed before operating the fireplace. The barrier is designed to reduce the risk of
burns from hot glass. Do not operate the fireplace without the barrier installed.
NOTE: All models must have a barrier installed prior to operation.
Glass Door
Area to
keep clear
Gasket
4
Printed in U.S.A. © 2018 Innovative Hearth Products
P/N 900935-00 Rev. NC 10/2018
Innovative Hearth Products (IHP) reserves the right to make changes at any time, without
notice, in design, materials, specifications, prices and also to discontinue colors, styles and
products. Consult your local distributor for fireplace code information.
1769 East Lawrence Street • Russellville, AL 35654
/
