Logik L90CHDB11 User manual

Brand: Logik

Model: L90CHDB11

Category: Cooker hoods

Type: User manual

This manual is also suitable for

L90CHDSS11

Logik L90CHDB11 is a 90cm Chimney Hood, designed for use in domestic households to extract vapours and remove odours from cooking. It can be used in two modes: air extraction, where the air is expelled outside through a duct, and air recirculation, where the air is cleaned through a carbon filter and recirculated back into the kitchen.

The hood has three fan motor speeds, allowing you to adjust the extraction power to the intensity of cooking odours. It also features hob lighting, providing additional illumination over the cooking area.

To ensure optimal performance, the grease filters should be cleaned regularly by hand or in the dishwasher. The carbon filter, used in air recirculation mode, should be replaced every 3-6 months, depending on usage.

Instruction Manual

90cm Chimney Hood

L90CHDSS11 (Stainlss Steel)

L90CHDB11 (Black)

Contents

Safety Warnings ............................................................................................................................ 4

Unpacking ..................................................................................................................................... 8

Product Overview ......................................................................................................................... 9

Modes of Operation ................................................................................................................... 10

Air Extraction ........................................................................................................................................................... 10

Air Recirculation .....................................................................................................................................................10

Operation .................................................................................................................................... 10

To Select the Fan Motor Speed .........................................................................................................................10

Hob Lighting ...........................................................................................................................................................10

Cleaning and Maintenance ........................................................................................................ 11

Grease Filters ........................................................................................................................................................... 11

Cleaning the Grease Filters by Hand ..............................................................................................................12

Cleaning the Grease Filters in the Dishwasher ...........................................................................................12

Carbon Filter Usage ..............................................................................................................................................13

Replacing Carbon Filters ..................................................................................................................................... 13

Changing the Lamps ............................................................................................................................................ 13

Hints and Tips ............................................................................................................................. 14

If Cooker Hood Does Not Operate ..................................................................................................................14

Technical Specication ............................................................................................................... 15

Installation .................................................................................................................................. 16

Product Overview ..................................................................................................................................................16

Safety Distance Between Hob and Cooker Hood ......................................................................................18

Connection for Air Extraction ...........................................................................................................................19

Mounting the Cooker Hood ..............................................................................................................................20

• This appliance complies with all relevant local and national safety requirements. Inappropriate use

can, however, lead to personal injury and damage to property.

• To avoid the risk of accidents and damage to the appliance, please read these instructions carefully

before using it for the rst time. They contain important information on the safety, installation, use

and maintenance of the appliance.

• Keep these instructions in a safe place and ensure that all users are familiar with the contents. Pass

them on to any future owner of the appliance.

Correct Application

• This appliance is not designed for commercial use. It is intended for use in domestic households.

• It must only be used as a domestic appliance to extract vapours and remove odours from cooking.

• Any other usage is not supported by the manufacturer and could be dangerous.

The manufacturer cannot be held liable for damage resulting from incorrect or improper use or

operation of the appliance.

• This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

• Accessible parts may become hot when used with cooking appliances.

• If the supplied mains cable is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualied persons in order to avoid a hazard.

Safety with children

• This appliance is only intended for use by adults who have read these instructions.

• This appliance is not a toy! To avoid the risk of injury, keep children well away and do not allow

them to play with it or to use the controls. They will not understand the potential dangers posed by

it. They should be supervised whenever you are working in the kitchen.

• Older children may use the cooker hood only when its operation has been clearly explained to them

and they are able to use it safely, recognising the dangers of misuse.

Correct Use

• Never use an open ame beneath the cooker hood. To avoid the danger of re, do not ambé or

grill over an open ame under the cooker hood.

When switched on, the cooker hood could draw ames into the lter. Fat particles drawn into the

cooker hood present a re hazard.

• When using the cooker hood over a gas hob, ensure that any burners in use are always covered by a

pan. Switch the cooking zone o when a pan is removed, even for a short time.

Safety Warnings

• Regulate the ame so that it does not burn up the sides of the pan.

• Do not allow the pans to overheat excessively (e.g. when using a wok).

• The cooker hood can become damaged when exposed to excessive heat.

• Always switch the cooker hood on when a cooking zone is in use, otherwise condensation may

collect in the hood, which could cause corrosion.

• When cooking with oil or fat, chip pans and deep fat fryers etc, do not leave the pans unattended.

Never leave an open grill unattended when grilling. Overheated oil and fat can ignite and could set

the cooker hood on re.

• Do not use the cooker hood without the lters in place. This way you will avoid the risk of grease

and dirt getting into the appliance and hindering its smooth operation.

• The lters should be regularly cleaned or changed as appropriate. Saturated lters are a re hazard.

See "Cleaning and Maintenance".

• The cooker hood can get very hot during cooking due to heat rising from the hob.

Do not touch the housing or the grease lters until the cooker hood has cooled down.

• Do not use a steam-cleaner to clean this appliance. Steam could reach the electrical components

and cause a short circuit.

Technical safety

• Before installation, check the cooker hood for visible signs of damage. Under no circumstances

should you use a damaged appliance. It could be dangerous.

• Before connecting the appliance to the mains supply, make sure that the voltage and frequency

details given on the data plate correspond with the on-site electricity supply, otherwise the

appliance could be damaged. Consult a qualied electrician if in any doubt.

• The electrical safety of this appliance can only be guaranteed when continuity is complete between

the appliance and an eective earthing system complies with the current local and national safety

regulations. It is most important that this basic safety requirement is present and tested regularly,

and where there is any doubt, the household wiring system should be inspected by a qualied

electrician. The manufacturer cannot be held liable for the consequences of an inadequate earthing

system (e.g. electric shock).

• For safety reasons, this appliance may only be used when it has been fully installed.

• Only open the housing as described in the instructions. Under no circumstances should any

other parts of the housing be opened. Tampering with electrical connections or components and

mechanical parts is highly dangerous to the user, and can cause operational faults.

• Installation, maintenance and repairs may only be carried out by an authorised person in

accordance with the current national and local safety regulations. Repairs and other work by

unqualied persons could be dangerous. The manufacturer cannot be held liable for unauthorised

work.

• Faulty components must only be replaced by genuine original parts.

• During installation, maintenance and repair work, the appliance must be disconnected from the

mains electricity supply. It is only completely isolated from the electricity supply when:

a) it is switched o at the isolator, or

b) the mains fuse is disconnected, or

c) it is switched o at the wall socket and the plug withdrawn, or

d) the fuse of the fused spur connection unit is withdrawn.

• Do not connect the appliance to the mains electricity supply by a multi-socket unit or an extension

lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating). This

appliance may only be used in mobile installations if a risk assessment of the installation has been

carried out by a suitably qualied engineer.

• In areas which may be subject to infestation by cockroaches or other vermin, pay particular

attention to keeping the appliance and its surroundings in a clean condition at all times.

• Great care should be taken when using the cooker hood at the same time and in the same room

or area of the house as another heating appliance which depends on the air in the room. Such

appliances include gas, oil, wood or coal-red boilers and heaters, continuous ow or other water

heaters, gas hobs, cookers or ovens which draw air in from the room and duct exhaust gases out

through a chimney or extraction ducting.

• When used in extraction mode, the appliance draws air in from the room in which it is installed

and from neighbouring rooms.

• If there is insucient air, an underpressure will occur. The heating appliance may be starved of

oxygen, impairing combustion.

• Harmful gases could be drawn out of the chimney or extraction ducting back into the room, with

potentially fatal consequences.

• In order to ensure safe operation, and to prevent gases given o by the heating appliances

from being drawn back into the room when the cooker hood and the heater are in operation

simultaneously, an underpressure of 0.04 mbar (4 pa) is the maximum permissible in the room.

Using at the same time as other heating

appliances that depend on the air from

the same room.

WARNING: Danger of toxic fumes.

• Ventilation can be maintained by air inlets

which must not be blocked, in windows,

doors and outside wall vents, or by other

technical measures, such as ensuring that

the cooker hood can only be switched on

when the heating appliance is switched o

or vice versa. A ventilation brick alone is not

generally sucient to ensure safe ventilation.

The overall ventilation condition of the dwelling must be taken into account. If in any

doubt, the advice of a competent builder or, for gas, a qualified gas fitter (Gas Safe

registered in the UK) must be sought.

Correct Installation

• Refer to the cooker or hob manufacturer's instructions as to whether a cooker hood may be

operated above the cooker/hob.

• The minimum safe distances between the top of the cooker or hob and the bottom of the cooker

hood given in the Installation section of this booklet must be maintained, unless the hob/cooker

manufacturer states that a greater safe distance is required.

• If more than one appliance is tted beneath the cooker hood, and they have dierent minimum

safe distances to the cooker hood, select the greater distance.

• Safety regulations prohibit the tting of a cooker hood over solid fuel stoves.

• All ducting, pipework and ttings must be of non-ammable material. These can be obtained from

builders' merchants.

• The appliance must not be connected to a chimney or vent ue which is in use. Neither should it be

connected to ducting which ventilates rooms with replaces.

• If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other

purposes, seek professional advice.

Accessories

• Only use genuine original spare parts and accessories with this appliance.

• If the only way of ensuring adequate ventilation is via an open window, a window contact switch

should be tted to ensure that the cooker hood can only operate when the window is opened

suciently. A window contact switch kit is available from good builders' merchants. Take care

when ventilating the room through an open window that ventilation is not impaired by a closed

blind or curtain. If the hood is being operated in recirculation mode, the above restrictions do not

apply.

If in any doubt , the advice of a qualified builder, gas fitter (Gas Safe registered in the UK) or

electrician must be sought.

The manufacturer cannot be held liable for damage caused by non-compliance with these

Warning and Safety instructions.

Instruction

Manual

Unpacking

Remove all items from the packaging Retain the packaging. If you dispose of it please do so according to local

regulations. The following items are included:

Main Unit

4 x 8mm Screws X 4Internal Chimney X 1

External Chimney X 1 Ф8 x 40mm

Plastic Wall Plug X 9

Hanging Plate

(for mounting product on the wall)

External Chimney Connection Plate

(for xing external chimney on the wall)

Internal Chimney Connection Plate

(for xing internal chimney on the wall)

4 x 30mm Screws X 2 4 x 40mm Screws X 7 Drill Template Instruction Manual

Thank you on the purchase of your new Logik Cooker Hood.

We recommend that you spend some time to read this manual in order to fully understand

how to install and operate it correctly.

Read all the safety warnings carefully before use and keep this manual for future reference.

If items are missing or damaged please contact Partmaster (UK only).

Tel: 0844 800 3456 for assistance.

Adapter X 1

(for reducing outlet diameter from 150-120mm)

3503C1

5-Ø8

Control Panel

1. OFF button

2. Motor speed buttons

3. Lamp button

12 3

3 4

Product Overview

1. Recirculation Vents

2. Internal Chimney

3. External Chimney

4. Control Panel

5. Illumination

6. Aluminium Filter

Modes of Operation

The cooker hood works with

Air Extraction

The air is drawn in and cleaned by the grease filters and directed outside.

When the cooker hood is switched on, the non-return flap opens for the cooking

vapours to be ducted away.

There must be adequate ventilation of the room when the cooker hood is used at the same time as

appliances burning gas or other fuels.

• Carbon filters are available as an optional extra, see rear page for ordering details.

• Before using the cooker hood in recirculation mode, ensure that the carbon filters are in place.

See “Cleaning and Maintenance”

Air Recirculation

The air is drawn in and cleaned first by the grease filters and then by a carbon filter. The

cleaned air is then recirculated back into the kitchen through the recirculation vents in

the top of the cooker hood chimney.

Operation

To Select the Fan Motor Speed

1. The unit has 3 motor speeds “1” , “2” and “3”.

2. For short periods of cooking food with intensive vapours and a strong aroma, e.g. when searing meat, you

may wish to select the highest setting “3”.

3. To turn the motor fan off, press the OFF button.

• Do not flambe under the cooker hood.

• Accessible parts may become hot when used with cooking appliances.

Hob Lighting

The hob lighting can be switched on and off independently of the fan by pressing the LAMP button.

• All external surfaces and controls can be cleaned using a little washing-up liquid applied with a damp soft

sponge or cloth.

Grease Filters

The re-usable metal grease filters in the appliance remove solid particles (grease, dust, etc.) from the kitchen

vapours, preventing soiling of the cooker hood.

The grease filters should be cleaned regularly (at least every 3-4 weeks) to avoid a build-up of grease.

1. To take out the grease filter, press the plastic catch.

2. Pull the aluminium filter downwards.

Cleaning and Maintenance

• Before any cleaning or maintenance work is carried out, disconnect the cooker hood from the mains

power supply. Ensure that:

– it is switched off at the isolator, or

– it is switched off at the wall socket and the plug is withdrawn, or

– the fuse from the fused spur connection unit is withdrawn, or

– the mains fuse is disconnected.

• The surfaces and controls are susceptible to scratches and abrasions. Please observe the following

cleaning instructions.

Do not use:

• Cleaning agents containing soda, acids, chlorides or solvents.

• Abrasive cleaning agents, e.g. powder cleaners or cream cleaners and abrasive sponges, as well as

pot scourers or sponges which have been used previously with abrasive cleaning agents as these

will damage the surface material.

Only use a damp cloth as water could get into the unit and cause damage.

Dirty filters are a fire hazard.

To avoid damaging the filters or the hob

below, make sure you hold the filters

securely at all times when handling them.

• Wipe dry using a soft cloth.

Cleaning the Grease Filters by Hand

• Clean the filters with a soft nylon brush in a mild solution of hot water and a little washing-up liquid.

Cleaning the Grease Filters in the Dishwasher

• Place the filters as upright as possible in the lower basket, with the short sides upright. Wash in

a 65°C programme, ensuring the spray arm is not obstructed.

• Use a mild dishwasher detergent.

Do not use:

• Cleaning agents containing descaling agents.

• Powder cleaners, cream cleaners or abrasive all-purpose cleaners.

• Oven cleaners.

Depending on the cleaning agent used, cleaning the filters in a dishwasher

can cause permanent discolouration to the surface. However, this will not

affect the functioning of the filters in any way.

• After cleaning, leave the filters to dry on an absorbent surface before replacing them.

• When removing the filters for cleaning, also clean off any residues of oil or fat from the now accessible housing

to prevent the risk of these catching fire.

When putting the grease filters back in position, ensure that the locking clips are facing down towards

the hob.

Carbon Filter Usage

Your product is compatible with one type of carbon filter (carbon filters are not provided).

• Before installing or replacing the carbon filters, you should switch off and disconnect the electricity supply.

• The carbon filters should never be washed.

• The grease filters should be installed on the product even when carbon filters are not being used.

Do not use your product without the grease filters.

Replacing Carbon Filters

• It is necessary to install 2 carbon filters in your product.

• Open all the grease filters, see page 7 for details.

• To attach the carbon filters, place them on the connection

channels on the motor and turn the left hand filter

anticlockwise and the right hand filter clockwise.

• In order to remove the carbon filters, turn the left hand

filter clockwise and the right hand filter anticlockwise.

• Replace the carbon filters when they no

longer absorb kitchen odours effectively.

They should, however, be replaced at least

every 3 months to prevent a risk of fire.

• Used carbon filters can be disposed of with

the normal household waste.

• Replace all the grease filters to the main unit.

Changing the Lamps

1. Disconnect the electricity supply.

2. Remove the aluminium grease filters.

3. Two candle lamps are located under the lamp

cover.

4. Replace with a 40W 240V (E14) candle lamp.

Hints and Tips

Problem Solution

Cooker hood does not operate

• Check Electric connection.

(The supply voltage should be 220-240 V. The cooker hood must

be connected to an earthed socket)

• Check motor speed selector.

(Motor speed selector should be in position I, II or III)

Lamp does not light

• Check Electric connection.

(The supply voltage should be 220-240 V. The cooker hood must

be connected to an earthed socket)

• Check lamp switch.

(Lamp switch should be in the on position)

• Check light bulbs.

Air suction of cooker hood is weak

• Check aluminium filters.

(Aluminium grease filters should be washed once a month under

normal conditions)

• Check air outlet chimney.

(Air outlet chimney should be open)

• Check carbon filters.

(If the unit operates with carbon filters, they should be replaced

quarterly)

If Cooker Hood Does Not Operate

Before Contacting Service:

Be sure that the mains plug is connected to the mains socket and the fuse in the installation is in good condition.

Check your cooker hood according to the above table. If the problem continues, contact your retailer or an

authorised service agent.

Technical Specications

Model no. L90CHDB11 / L90CHDSS11

Extraction Rate (m3/h) 450

Voltage (V) 220 – 240 ~

Frequency (Hz) 50

Total Power (W) 180

Lamp 2 × 40 W

Features and specifications are subject to change without notice.

Installation

Product Overview

3 4

1. Grill For Air Outlet

2. Internal Chimney

3. External Chimney

4. Internal Chimney Connection Plate

5. External Chimney Connection Plate

6. Hanging Plate

All dimensions shown are in mm.

276303

400

500 900

480-860

Min.650 mm

Safety Distance Between Hob and Cooker Hood

When planning the installation height of your cooker hood, the minimum safe distance between the

top of a cooker or hob and the bottom of the cooker hood should be at least 650mm, unless a greater

distance is specified by the manufacturer of your cooking appliance.

• When deciding on the safe distance between the hob and cooker hood, please note that a distance greater

than 650mm above electric cookers/hobs may be preferable to give more working space under the hood.

• Account should also be taken of the height of the person who will be using the hood most often. The person

should have sufficient space to work comfortably at the hob, and also be able to reach the hood controls with

ease.

• Please be aware that if positioned too high, extraction will be inefficient.

• If you want the top of the cooker hood telescopic extension piece to be mounted flush with the ceiling, make

sure there is adequate space below the appliance for safe operation.

Connection for Air Extraction

Only use smooth pipes or flexible hoses made from non-flammable materials for the extraction ducting.

To achieve the greatest possible air extraction with the lowest noise level, please note the following:

• To ensure efficient air extraction, the diameter of the exhaust ducting should not be less than

120mm.

• If flat ducting is being used, the cross-sectional area must not be smaller than the cross sectional area of the

exhaust connection.

• All ducting, pipework and fittings must be made of non-flammable materials.

• The exhaust ducting should be as short and straight as possible.

• Only use wide radius bends.

• The exhaust ducting should not be kinked or compressed.

• Ensure that all connections are strong and airtight.

• Where ducting is horizontal, it must be laid to slope away at least 1 cm per metre. This is to ensure that

condensation cannot drain back into the cooker hood.

• If the exhaust air is to be ducted into the open air, the installation of a telescopic wall vent or roof vent is

recommended.

To avoid the danger of toxic fumes, please observe the Safety Warnings.

This is especially crucial when using the cooker hood at the same time as another heating appliance

which relies on air from the same room.

The cooker hood should be installed according to the local and national building regulations. Seek

approval from the building inspector where necessary.

If the exhaust ducting is to run through rooms, ceiling space etc. where there may be great variations

in temperature between the different areas, the problem of condensation will need to be addressed.

The exhaust ducting will need to be suitably insulated.

Mounting the Cooker Hood

1. We recommend that for air extraction installations, a professional tradesperson is consulted prior to any

work being undertaken. A 150mm or 120mm hole will need to be provided for the aluminium flexible hose

(not supplied) to duct the extracted air to the outside. For recirculation operation, a competent layman

can follow the instructions below. If you are in any doubt, we recommend you consult a professional

tradesperson.

2. Ensure there is an available switched mains socket adjacent to the hood to power the appliance. If this

is not available, do not use extension leads. We recommend you consult a qualified electrician prior to

commencing any work.

3. You can either use the drill template to mark the position of the fixing screws or position the hood on the

wall and mark the position "A", "B", "C", "D" and "E" as shown.

4. Screw the External Chimney to the External Chimney Connection Plate by screwing 2 pcs of the 4 x 8mm

screws through the mounting holes at the top of External Chimney. Screw the Internal Chimney to the

Internal Chimney Connection Plate by screwing the other 2 pcs of 4 x 8mm screws through the mounting

holes at the top of Internal Chimney.

• We recommend professional that tradespersons are consulted prior to the fitting of this appliance.

• Each installation is different and these instructions should be used as a guide only. If in doubt

consult professional tradespersons.

• Air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas

or other fuels.

Before drilling any holes, ensure there is no pipe work or wires buried in the wall.

230

300

F G

E B

256

242 250

Page is loading ...

Logik L90CHDB11 User manual

Brand: Logik

Model: L90CHDB11

Category: Cooker hoods

Type: User manual

This manual is also suitable for

L90CHDSS11

Download PDF

report

Logik L90CHDB11 User manual

This manual is also suitable for

Logik L90CHDB11 User manual

Related papers

Other documents