WaterWorks BDTH58 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
WaterWorks BDTH58, a thermostatic valve with metal cross handle shutoff trim, offers precise temperature control and anti-scald protection for a safe and comfortable showering experience. Its stylish design and durable construction make it a perfect addition to any bathroom.
WaterWorks BDTH58, a thermostatic valve with metal cross handle shutoff trim, offers precise temperature control and anti-scald protection for a safe and comfortable showering experience. Its stylish design and durable construction make it a perfect addition to any bathroom.
STYLE No. BDTH58
Boulevard Metal Lever Handle Thermostatic
with Metal Cross Handle Shutoff Trim
INSTALLATION GUIDELINES
PAGE 1 OF 5 | UPDATED ON 6.4.2019
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
IMPORTANT:
To ensure this product is installed properly, you must read and
follow these guidelines.
The owner/user of this product must keep this information for
future reference.
This product must be installed by a professional licensed
contractor and must be onsite prior to rough-in, this allows the
installer to visualize the installation.
Be sure your installation conforms to federal, state, and loc
a
codes. In the State of Massachusetts, all installations must compl
y
with the rules and regulations set forth within 248 CMR.
This product MUST BE installed vertically as shown and CANNOT
be installed horizontally. This product is intended to work with the
Universal Thermostatic Valve with Integrated Volume Control
Valve (Style No. GUTH46).
WARNING: GUTH46 features anti-scald protection. The risk of
scalding exists until the installer has properly calibrated/adjusted
the temperature setting during final trim installation.
Inspect this product to ensure you have all the parts required for
proper installation. Product is sold partially assembled but shown
fully disassembled for illustrative and service purposes only.
Use only a strap wrench or protected/smooth-jaw wrench on any
finished surface.
The use of certain plumber’s putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support
at 1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
REQUIRED PLUMBING DETAILS:
Boulevard Thermostatic Valve
STYLE No. GUTH46
ROUGH-IN AND VALVE PREPARATION:
CAUTION: Make sure the supply lines are flushed prior to final TRIM installation using the
FLUSH PLATE provided with the VALVE. Refer to the Installation Guidelines provided with the
VALVE for further information on how to properly flush the supply lines.
DIM VALUE
A 2-1/4” MIN [57mm]
B Ø5-1/4” [133mm]
C Ø1-3/8” [35mm]
‡ IMPORTANT: The CARTRIDGE is packaged separately and provided with the VALVE.
SERVICE
STOP*
CARTRIDGE ‡
FINISHED
WALL
FLUSH PLATE
[DO NOT DISCARD]
CARTRIDGE
SCREW
THREADED
TUBE
TILE
GUARD
O-RING
TILE
GUARD
"B"
FITTINGS
HOLE
"C"
FITTINGS
HOLE
"A"
ROUGH-IN
DEPTH
CENTER
OF INLET
SERVICE STOP*
STYLE No. BDTH58
Boulevard Metal Lever Handle Thermostatic
with Metal Cross Handle Shutoff Trim
INSTALLATION GUIDELINES
PAGE 2 OF 5 | UPDATED ON 6.4.2019
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
VOLUME CONTROL
VALVE
FINISHED
WALL
THREADED TUBE
VOLUME CONTROL
VALVE
FINISHED
WALL
THREADED TUBE
1-7/16"
[37mm]
4. Mark the THREADED TUBE on the VOLUME
CONTROL VALVE 1-7/16” [37mm] beyond where it
protrudes from the finished wall.
5. Remove the THREADED TUBE then cut the TUBE
at the previous mark.
CAUTION: Do NOT cut the end with the internal
threads.
FINISHED
WALL
CARTRIDGE
STEM
FINISHED
WALL
VOLUME CONTROLVOLUME CONTROL
VALVEVALVE
CARTRIDGE
STEM
2"
[51mm]
6. Mark the CARTRIDGE STEM on the VOLUME
CONTROL VALVE 2” [51mm] beyond where it
protrudes from the finished wall.
FINISHED WALL
ALL THREAD TUBE
FINISHED WALL
ALL THREAD TUBE
TRIM PLATE
FINISHED
WALL
ALL THREAD TUBE
FINISHED
WALL
ALL THREAD TUBE
3/16"
[5mm]
MARK LINE
TRIM
PLATE
ALL
THREAD
TUBE
TRIM
PLATE
CUT TUBE
AT PREVIOUS
MARK
DO NOT CUT END
WITH INTERNAL
THREADS
1. Thread the ALL THREAD TUBE onto the
THERMOSTATIC VALVE then slide the TRIM PLATE
over the TUBE.
2. Firmly holding the PLATE against the finished wall,
mark the TUBE 3/16” [5mm] beyond where it
protrudes from the TRIM PLATE.
3. Remove the PLATE and TUBE then cut the TUBE at
the previous mark.
CAUTION: Do NOT cut the end with the internal
threads.
THREADED
TUBE
CUT TUBE
AT PREVIOUS
MARK
DO NOT CUT END
WITH INTERNAL
THREADS
STYLE No. BDTH58
Boulevard Metal Lever Handle Thermostatic
with Metal Cross Handle Shutoff Trim
INSTALLATION GUIDELINES
PAGE 3 OF 5 | UPDATED ON 6.4.2019
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
CARTRIDGE STEMCARTRIDGE STEM
CUT STEM AT
PREVIOUS MARK
7. Remove the CARTRIDGE using a 21/32” [17mm]
shower valve socket wrench (not provided) then
cut the STEM at the previous mark.
CARTRIDGE
THREADED
TUBE
10. With the CROSS HANDLE in the desired orientation
and using the WASHER provided, thread and
securely tighten the GLAND COVER onto the upper
TUBE.
8. Thread and securely tighten the CARTRIDGE back
into the VOUME CONTROL VALVE then thread the
THREADED TUBE back onto the CARTRIDGE.
9. Thread the ALL THREAD TUBE back onto the
THERMOSTATIC VALVE, slide the TRIM PLATE
over both TUBES then thread and securely tighten
the TRIM NUT onto the lower TUBE to firmly hold
the PLATE against the finished wall.
TRIM PLATE
PLASTIC WASHER
GLAND COVER
CROSS HANDLE
SQUARE TUBE
TRIM
PLATE
SQUARE TUBE
SHOULD FEEL
RESISTANCE
SQUARE TUBESQUARE TUBE
MARK
LINE
1/8"
[3mm]
TRIM NUT
CUT
LINE
11. Insert the SQUARE TUBE into the TRIM NUT then,
by feel, make sure it slides over the CARTRIDGE
STEM and is fully seated.
NOTE: When seated properly, the TUBE will have
rotational resistance.
12. Mark the SQUARE TUBE where it passes through
the front face of the TRIM NUT then remove and
cut the TUBE 1/8” [3mm] behind the previous
mark.
ALL
THREAD
TUBE
TRIM PLATE *
[WITH GASKET]
TRIM
NUT
* A GASKET for the TRIM PLATE
is provided. If desired, a bead of
caulk or a clear silicone may be
applied where the PLATE
contacts the finished wall.
STYLE No. BDTH58
Boulevard Metal Lever Handle Thermostatic
with Metal Cross Handle Shutoff Trim
INSTALLATION GUIDELINES
PAGE 4 OF 5 | UPDATED ON 6.4.2019
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
VALVEVALVE
* TURN ON WATER
MIXED
COLD
HOT
FLAT HEAD
SCREWDRIVER
FLAT HEAD
SCREWDRIVER
MAXIMUM
MINIMUM
TEMP °C/°F
x2
TURNS
COLD
HOT
17. Place the LIMIT STOP onto the TRIM NUT making
sure the LIP on the STOP sits properly inside the
GROOVE in the PLATE then securely tighten the
SET SCREWS.
18. Turn the LIMIT STOP to full cold then full hot and
confirm it is functioning properly. Verify the
maximum desired bathing temperature.
NOTE: If necessary, repeat the calibration process.
TEMP °C/°F
DESIRED MAX
LIMIT
STOP
SET SCREW
[x4]
[2mm HEX]
[GROOVE]
[LIP]
TRIM NUT
LIMIT STOP
WARNING: IT IS NOT RECOMMENDED
TO EXCEED A SAFETY LIMIT STOP OF
37.8°C/100°F.
2. TURN UNTIL
STOP AND
CHECK MAX
TEMP °C/°F
1. TURN FULL COLD
16. With water running, rotate the SQUARE TUBE to
adjust the temperature to the maximum desired
bathing temperature, verified with a thermometer,
then turn the water off.
CAUTION: Make sure NOT to change this setting.
SQUARE TUBESQUARE TUBE
SQUARE TUBE
TRIM NUT
13. Re-insert the SQUARE TUBE back into the TRIM
NUT making sure it is slightly recessed.
14. Turn on the water supply and open the VOLUME
CONTROL VALVE to run water through the
THERMOSTATIC VALVE.
15. Insert a bladed screw driver into the SQUARE TUBE
and slowly rotate the TUBE clockwise to attain full
cold then counterclockwise to attain full hot. It’s
approximately 2 complete rotations. Verify a full
range of temperatures exists.
STYLE No. BDTH58
Boulevard Metal Lever Handle Thermostatic
with Metal Cross Handle Shutoff Trim
INSTALLATION GUIDELINES
PAGE 5 OF 5 | UPDATED ON 6.4.2019
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
19. With the LEVER HANDLE in the desired orientation
and using the WASHER provided, thread and
securely tighten the GLAND COVER onto the LIMIT
STOP.
GLAND
COVER
LIMIT STOP
PLASTIC
WASHER
LEVER HANDLE
20. Turn on the water supply and operate both
HANDLES to ensure that they are functioning
properly.
* TURN ON WATER
-
1
-
2
-
3
-
4
-
5
WaterWorks BDTH58 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
WaterWorks BDTH58, a thermostatic valve with metal cross handle shutoff trim, offers precise temperature control and anti-scald protection for a safe and comfortable showering experience. Its stylish design and durable construction make it a perfect addition to any bathroom.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WaterWorks RGVC11 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Speakman SM-5490-ADA Installation guide
-
-
Moen L2700 User manual
-
Delta Faucet T17282-SS Installation guide
-
Delta T17494-CZ-I Installation guide
-
-
-
Sigma 18.30.171 Installation Instructions Manual
-
Cooper 1700 Series Installation guide
-
Delta Faucet T17T467-BL Owner's manual