Simplicity CAB FOR SNAPPER TURF/TRAIL CRUISER User manual

  • Hello! I am an AI chatbot trained to assist you with the Simplicity CAB FOR SNAPPER TURF/TRAIL CRUISER User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
# 7600015 CAB For Snapper
Turf Cruiser and Trail Cruiser
OPERATION - PARTS LIST - ASSEMBLY
IMPORTANT !
READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE
CAUTION
REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER
! WARNING
THIS CAB WILL NOT PROTECT OPERATOR FROM INJURIES CAUSED BY ROLLOVER, COLLISION, OR OTHER
ACCIDENTS
FORM 40226605 1
For Replacement Parts and Accessories Contact:
Original Tractor Cab Co., Inc.
P.O. Box 97 6849 W. Front St.
Arlington, IN 46104
Phone 765-663-2214
Fax 765-663-2101
Visit us on the web to see our other products.
www.originalcab.com
Cabs for Lawn Tractors, Garden Tractors, Compact Tractors, Snow Blowers, Utility Vehicles
Sunshades for Tractors, Mowers, & Utility Vehicles
Storage Covers for Lawn and Garden equipment.
LIMITED WARRANTY
COVERED BY WARRANTY
ORIGINAL TRACTOR CAB CO., INC., (the "Company") warrants to the owner that each new product listed below is merchantable and free of defects in
workmanship and material.
During the warranty period, the dealer from whom the product was bought, or the Company, will provide, free of charge, parts and the shipping costs of parts
necessary to correct any defect in workmanship and material.
WARRANTY PERIOD
The company products listed below are warranted for the stated period from the date of the original purchase:
1. Cabs for tractors and snow removal equipment 1 Year
2. Company manufactured accessories for above cabs 1 Year
3. Sunshades for lawn and garden tractors 1 Year
4. Repair parts 1 Year
OWNER'S RESPONSIBILITIES
The owner of a new Company manufactured product must do the following to qualify for warranty service:
1. Retain the original invoice or other proof of purchase to avoid unnecessary difficulties in determining eligibility for warranty work.
2. Notify the dealer from whom the product was bought, or the company, as soon as possible after discovery of a possible defect, and provide proof of original
purchase.
To notify the company write to: Original Tractor Cab Co., Inc., P.O. Box 97, Arlington, IN 46104.
3.the owner may, upon notification by the Company, be required to return the defective part, or parts, to the Company for inspection and warranty service.
NOT COVERED BY WARRANTY
The following are not covered by this warranty:
1. Transportation charges to and from servicing dealer or the Company;
2. New products that have been subject to misuse, negligence or accident, or have been altered or repaired in a manner not authorized by the company;
3. Windshield wipers, lights, or accessories that are warranted separately by their respective manufacturers, except Company agrees to make available to
the owner whatever warranty benefits may be made available to the Company by the manufacturers.
All implied warranties, except to the extent prohibited by any applicable law, shall have no greater duration than the warranty period for the
applicable product, some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
The Company’s' liability arising out of warranties representation, instructions, or defects from any abuse, shall be limited exclusively to repair or
replacing parts under the condition in the warranty, and in no event will Company be liable for incidental or consequential damages. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have rights that vary from state to state.
2
WARNING
This cab is designed to provide foul weather protection only. It does not provide protection
from noise, exhaust fumes, chemicals or injury from collision, roll-over, or other accidents.
1. Do not operate machine in confined areas without proper ventilation
2. Thoroughly check area of operation before using machine
3. The cab adds height to the machine. Low tree limbs and other overhead structures that did
not interfere with the operation of the machine before, may now be obstacles.
4. Fasten your safety belt.
MAINTENANCE INSTRUCTIONS
Periodically check all bolts to see that they are tight. If bolts become loose, failure of cab parts may
occur.
Door latches and hinges should be lubricated with light machine oil for proper operation.
DO NOT CLEAN THE CLEAR PLASTIC WINDOWS WHEN THE PLASTIC IS DRY.
THE CLEAR PLASTIC WILL SCRATCH.
Avoid contact with plastic windows. Keep plastic windows clean by washing them with clear running
water and rubbing with your bare hands, only. The use of a rag, sponge or brush will scratch the plastic.
Liquid soap may also be used for window cleaning. During freezing weather, an automotive windshield
washer solvent may be used.
Use liquid soap and water to clean colored vinyl portions. Scrubbing with a brush or rag is also
permitted on the colored vinyl portions
STORAGE INSTRUCTIONS
Prior to storage clean the windows and colored vinyl parts with a mild automotive detergent, rinse with
clean water and allow to thoroughly dry, Store cab in a clean dry place out of direct sunlight. Avoid
folding plastic windows.
READ THIS MANUAL COMPLETELY BEFORE BEGINNING INSTALLATION.
Park the machine on level ground, set the parking brake and remove the key before beginning
cab installation.
The right side of the machine is determined from the operators seated position.
The words "bolt" will refer to a 1/4”x5/8” bolt and "lock nut"’ will refer to a 1/4” locknut unless
specified otherwise.
Do not tighten bolts during assembly unless instructed to do so.
3
Carton Contents: Cab # 40226 for Turf & Trail Cruiser
KEY# PART# QTY. DESCRIPTION
1 40228 1 Foot, RH
2 40229 1 Foot, LH
3 40230 1 Rear Bracket, RH (short tabs)
4 40231 1 Rear Bracket, LH
5 40148 2 Front Posts
6 40086 1 Front Panel Frame Cross Bar
7 10750 1 Rear Post, RH
8 10751 1 Rear Post, LH
9 40233 1 Rear Curtain Support 1/2 (Reduced End)
10 40234 1 Rear Curtain Support 1/2
11 40235 2 ROPS Bracket
12 40251 1 Top Frame
13 40236 1 Rear Curtain
14 40237 1 Front Panel Vinyl
15 40250 1 ABS Plastic Top
16 40004 1 Windshield Assembly
17 40238 1 Door, RH
18 40239 1 Door Bottom, RH
19 40240 1 Door, LH
20 40241 1 Door Bottom, LH
9820 1 Door Latch Package
10121 1 Manual Windshield Wiper
40243 1 1” x 8’ Adhesive Hook Fastener
40242 1 Hardware Package (contents listed below)
786 16 1/4”-20 x 5/8” Cap Screw, hex
788 2 1/4”-20 x 3/4” Cap Screw, hex
5144 2 1/4”-20 x 2 3/4” Cap Screw, hex
730 18 1/4”-20 Two-Way Locknut
1514 4 1/4” Flat Washer
2 2
1/4” Split Lock Washer
906 2 3/8”-16 x 1” Cap Screw, hex
2908 2 3/8” Flat Washer
790 2 3/8” Two Way Locknut
9813 2 Large Plastic Protector
4902 2 Small Plastic Protector
Step 1; See Figure 1:
Figure 1 4
Remove handles from machine
A. Remove the four bolts that hold the Plate on
the right side. Remove the plate. Remove the
bolts and the handle.
B. Do not replace the plate and bolts at this
time.
C. Remove the left handle by accessing the
bolts under the seat mount.
Step 2; See Figure 2:
A. Use Figure 2 to identify all of the steel parts.
11
12
8
5
7
9
6
10
2
4
1
3
Figure 2
5
Step 3; See Figure 3 & 3a:
Install Foot Right (1) and Foot Left (2).
A. Remove the two bolts that hold the dash to
the fenders.
B. Insert the right Foot between the dash and
fender as shown with the tab leaning forward.
C. Replace the bolts. Do not tighten at this
time.
D. Repeat the above steps on the left side with
the left Foot. Figure 3
1
Figure 3a
Step 4: See Figure 4:
Install right & left Rear Bracket (3 & 4)
A. Replace the plate on the right side. Insert
1/4” x 5/8” bolts with 1/4” lock washers through
the tabs on the right Rear Bracket (short tabs).
Replace the two forward bolts that hold the
plate. Tighten the bolts.
B. Install the left Rear Bracket in similar fashion
on the left side.
3
Figure 4
6
Step 5; See Figure 5:
Install Front Posts (5) and Front Panel Frame
Cross Bar (6).
A. Use two bolts and nuts to attach the posts to
the right and left foot. Tighten just enough to
keep the posts upright.
B. Use two bolts and nuts to secure the Front
Panel Frame Cross Bar to the posts as shown.
Figure 5
Step 6; See Figure 6:
Install Rear Posts Right & Left (7 & 8) and Rear
Curtain Support halves (9 &10).
A. Insert a 1/4” x 3/4” bolt through the hole in
the rear bracket.
B. Place the Rear Curtain Support over the bolt
then place the lower end of the Rear Post left
over the bolt. Add a nut and tighten just enough
to keep the post and rear support
upright as shown.
C. Repeat the above steps on the right side.
Note: Latch plate on rear post should be on
front side of the post with the notch to the
outside. Rear Curtain Support should be level.
5
6
7
8
9
10
Figure 6
7
Step 7; See Figure 7:
Install ROPS Brackets (11) and Top Frame (12).
Door alignment.
A. Place the Rops Brackets on the rops as
shown. Insert two 1/4” x 2 3/4” bolts up through
the holes. Add nuts. Do not tighten at this time.
11
B. Place the Top Frame onto the bent ends of
the posts. Insert four bolts upwards and add
locknuts. Do not tighten at this time.
C. Insert two 3/8” x 1” bolts up through the
holes in the Rops Bracket and the tabs on the
Top Frame. Place a 3/8” flat washer over each
bolt and add a 3/8” locknut. Do not tighten at
this time.
D. Follow the instructions in the Door Hardware
Package to install the Door Bottoms and the
Door Latches. Figure 7
E. Install and latch both Doors for proper
alignment
F. Tighten all framework bolts at this time.
G. Place the notched plastic covers on the bent
ends of the rear posts and place the round
plastic covers on the tabs at the rear. (at white
arrows)
Step 8; See Figure 8:
Apply adhesive fastener to fender.
A. Thoroughly clean the area where the
adhesive fastener is to be applied.
B. Apply the fastener to the inside edge of the
fender to correspond with the fastener strip
sewn to the forward edge of the door.
C. Remove the doors.
NOTE: To remove doors, lift the rod out of the
bottom hinge and then lower it out of the top
hinge.
12
Inside rear edge
of ri
g
ht fende
r
Figure 8
8
Step 9; See Figure 9:
Install Rear Curtain (13).
A. Close the snap flaps around the top frame at
the back and corners.
B. Close the snap flaps over the rear posts and
brackets.
C. Thoroughly clean the area where the
adhesive fastener is to be applied.
D. Apply adhesive fastener to the area behind
the seats and to the console to correspond with
the fastener pieces sewn to the Rear Curtain.
13
.
E. Press the fastener together.
Figure 9
Step 10; See Figure 10:
Install Front Panel Vinyl (14).
A. Lay the rod sewn into the top of the Front
Panel Vinyl over the cross bar. Close the snap
flaps around the posts and feet.
14
B. Thoroughly clean the area where the
adhesive fastener is to be applied.
C. Apply adhesive fastener to the rear edge of
the hood to correspond with the fastener sewn
to the Front Panel Vinyl.
Figure 10
9
Step 11; See Figure 11 & 11a:
Install Windshield (16) & ABS Plastic Top (15)
A. Place the Plastic Top on the top frame.
B. Set the bottom lip of the windshield frame on
top of front panel vinyl and the front panel frame
cross bar. Raise the front of the top up and
push the windshield against the frame. Lower
the top trapping the windshield in place.
C. Insert four bolts with 1/4” flat washers
through the top and the tabs. Add locknuts and
tighten.
D. Install the Windshield Wiper per the
instructions in the Wiper package.
E. Install the assembled doors and connect the
fastener strips.
Optional Cab Accessories:
# 9855 Flashing Amber Caution Light
# 11133 Rear View Mirror, R or L Mount
# 40009 Electric Wiper Conversion
Figure 11
15
Figure 11a
16
10
/