Optex Infinity VXI-RDAM Installation Instructions Manual

Brand: Optex

Model: Infinity VXI-RDAM

Category: Motion detectors

Type: Installation Instructions Manual

This manual is also suitable for

Optex Infinity VXI-RDAM is a battery operated outdoor detector with advanced features designed to provide reliable detection performance. Its 12m detection pattern with 90 degree coverage can be adjusted to five different ranges, making it suitable for various outdoor environments. The device utilizes advanced temperature compensation and noise immunity technology to minimize false alarms. Its anti-masking feature detects covering objects, while the microwave sensor enhances detection accuracy, particularly in challenging conditions.

-1-

INSTALLATION INSTRUCTIONS

No.59-1936-1

VX InfinityTMseries

CONTENTS

VXI-R Battery operated model with 2 PIR

VXI-RAM VXI-R with anti-masking

VXI-RDAM VXI-RAM with micro-wave

INTRODUCTION

1-1 BEFORE INSTALLATION

1-2 PARTS IDENTIFICATION

1-3 DETECTION AREA

INSTALLATION

2-1 WIRING DIAGRAM

2-2 R MODEL BATTERY BOX RBB-01 (OPTION)

2-3 TRANSMITTER PREPARATION

2-4 BEFORE MOUNTING

2-5 WALL TAMPER WRS-04 (OPTION)

2-6 MOUNTING

2-7 AREA ANGLE ADJUSTMENT

2-8 AREA MASKING

2-9 DETECTION LENGTH ADJUSTMENT

SWITCH SETTING

WALK TEST

LED INDICATION

BATTERY

6-1 HOW TO REPLACE BATTERY

6-2 BATTERY LIFE

SPECIFICATIONS

7-1 SPECIFICATIONS

7-2 DIMENSIONS

SETTING OF SPECIAL DETECTION AREA

BATTERY OPERATED MODEL

MULTI DIMENSIONAL OUTDOOR DETECTOR

The VX InfinityTM series provide highly reliable detection functions, reducing false reports or

report losses. The VX InfinityTM series deliver stable detection performance even in severe

outdoor environments.

FEATURES

12 m (40 ft.) by 90 degree flexible detection pattern adjustable to 5 ranges

- SMDA Logic for advanced temperature compensation and environmental noise immunity.

- Easy Masking for over spill prevention

- Double Conductive Shielding against bright light disturbance.

- Conduit/TX-Battery Case for both wired and wireless-ready models.

BASIC FEATURES

- Active IR Anti-Masking for detecting covering objects

- Tough Mod Dual Technology based on OPTEX gold-plated microwave module

- Super Low Energy Circuit for maximum Battery life expectancy

OPTIONAL FEATURES

-2-

INTRODUCTION

1-1 BEFORE INSTALLATION

Warning

Caution

Failure to follow the instructions provided with this indication and improper handling may cause

death or serious injury.

Failure to follow the instructions provided with this indication and improper handling may cause

injury and/or property damage.

The check mark indicates recommendation.

The nix sign indicates prohibition.

• Sunlight and reflection • Heat source • Objects moving in the wind

0.8 – 1.2 m

(2.64 – 3.94 ft)

Parallel

Do not remove the PCB. Keep product away from direct splash.

Mounting height. Keep the detector parallel to the

ground.

Consider the direction a person is

approaching from, as well as the

detection area.

Install the detector in a place where it is free from false alarm factors. For example:

Warning

Tilt

-3-

1-2 PARTS IDENTIFICATION

-Precautions for installing two or more sensors

Masking seal × 3 pcs

Screw kit

For wall mounting

Screw (4 × 20 mm)

Connector for POWER and ALARM

Cover unit

Main unit

Back box

Back box cap

Mounting plate

Connector for TROUBLE

1.0 m (3.28 ft) or more Less than 1.0 m (3.28 ft)

Velcro tape

VXI-R

VXI-RAM

VXI-RDAM

Do not install two or more VXI-RDAMs in side by side or face to face. Doing so may cause

malfunction. VXI-RDAM may be installed in back to back. If mounting on the same wall, make

sure that each unit is at least 1.0m (3.28 ft) apart from the other.

Optional accessories

Wall tamper (WRS-04)

-3-

Battery box (RBB-01)

-4-

INSTALLATION

1-3 DETECTION AREA

2-1 WIRING DIAGRAM

Trouble

Tamper

Alarm

Transmitter

Note>>

• The battery in the transmitter is shared with

the detector.

• Connection for TROUBLE is used when

monitoring for Tamper and Anti Mask.

Note>>

Be sure to insert the battery box all the

way until it clicks.

Transmitter side Main unit side

OPTION: WRS-04

Red

Black

White

Yellow

Red: Power input (+)

Black: Power input (-)

White: Alarm

Yellow: Alarm

Green: Trouble

Blue: Trouble

Brown: Tamper

Orange: Tamper

Gray: Tamper

Green

Blue

Brown

Orange

Gray

Mount the battery box inside the

back box as shown below.

Insert the battery box along the

groove of the back box.

Click!

Back box

Battery box

mounting space

fghi

TOP VIEW

SIDE VIEW

Length limiting position 1 (Default)

PIR

Area diagram of horizontal position D

12m

12m 10m 12m10m5m 5m0

10m

ABCEFG

0 5m 10m 12m

Length limiting position 2

0 5m 10m 12m

Length limiting position 3

0 5m 10m 12m

Length limiting position 4

0 5m 10m 12m

Length limiting position 5

0 5m 10m 12m

Note>>

The maximum detection length may vary as

shown below due to environment conditions.

2-2 R MODEL BATTERY BOX RBB-01 (OPTION)

-5-

2-3 TRANSMITTER PREPARATION

2-4 BEFORE MOUNTING

<To monitor only the ALARM using a transmitter

with 1 external input>

<To monitor the ALARM and TROUBLE using a

transmitter with 2 external inputs>

35 (1.38)

130 (5.12)

30 (1.18)

External input is N.C. External input is N.O.

... DIP switch 3: OFF (N.C.)

... DIP switch 3: ON (N.O.)

Connectors to be used

Connector for POWER and ALARM

Connector for TROUBLE

Red Black

How to position a battery

Connector for POWER

and ALARM

Connector for

TROUBLE

Connector for

POWER and ALARM

N.C. N.O.

Unit: mm (inch)

The transmitter used should have the internal dimensions of H 150 × W 34 × D 33 mm(H 5.91 × W 1.34 × D 1.30 inch)

or H 112 × W 55 × D 35 mm.(H 4.41 × W 2.17 × D 1.38 inch)

WRS-04 (option) Store the connecting

cable in a trench

and seal with a label

already in place.

Remove the cap.

1Open the cover unit.

2Remove the main unit from

the back box.

3Remove the back box

from the mounting plate.

Mount the wall tamper

(WRS-04) on the back

of the main unit.

1Run the wire along

the wiring groove.

2-5 WALL TAMPER WRS-04 (OPTION)

-6-

2-6 MOUNTING

Wall mount Pole mount

Metal band

Velcro tape

Transmitter

Transmitter side Main unit side

Red

Black

White

Yellow

Red: Power input (+)

Black: Power input (-)

White: Alarm

Yellow: Alarm

Green: Trouble

Blue: Trouble

Green

Blue

Note>>

• The battery in the transmitter is shared with the detector.

• Connection for TROUBLE is used when monitoring for

Tamper and Anti Mask.

* Use a metal band with

25 mm or less in width.

Put the top of the back

box on the hook.

1Mount the mounting plate. 2Mount the back box on the mounting plate.

3Mount the transmitter on the back of the main unit. 4Connect the connectors

5Mount the main unit to the back box. 6Put the cap on top.

-7-

2-7 AREA ANGLE ADJUSTMENT

2-8 AREA MASKING

Horizontal position D

(Default)

Horizontal position B

(F: symmetrical

position)

Horizontal position C

(E: symmetrical

position)

Horizontal position A

(G: symmetrical

position)

ABCEFGD

ABCEFG

Note>>

When creating a special detection area, refer to the end of this manual.

If there is an unwanted object within the detection area, apply an area masking label to the appropriate area.

Insert the protruding

part of the cover into

the lens hole.

Fit the edge of the

lens.

Slide the lens holder to secure it.

Unwanted

object (Tree)

3Insert the lens into the cover. 4Mount the lens holder to the cover.

The angle can be adjusted in

7 levels from A to G.

The detection area becomes

14 zones only when A or G is

selected.

1Slide the lens holder and remove the lens holder out

of the cover as shown below. 2Identify positions to mask on the lens and apply a

corresponding strip from the masking sheet 1.

-8-

2-9 DETECTION LENGTH ADJUSTMENT

MW sensitivity

adjustment

Both upper and lower detection

area are blocked

IMPORTANT

BOTH DETECTION AREAS MUST BE

BLOCKED FOR DETECTION

Detection!

Detection

Only upper detection area is blocked

Only lower detection area is blocked

1Adjust the PIR detection length by sliding the lower

PIR to the desired position.

2Adjust the MW detection length by rotating the MW

sensitivity adjustment according to the PIR area.

Detection length setting chart

* The detection lengths described above should be used as a guideline.

Position

(Factory

default)

12.0 m

(40.0 ft)

8.5 m

(27.9 ft)

6.0 m

(19.7 ft)

3.5 m

(11.5 ft)

2.5 m

(8.2 ft)

10.0 -17.0 m

(32.1 - 55.8 ft)

7.0 - 12.0 m

(23.0 - 39.4 ft)

5.0 - 8.5 m

(16.4 - 27.9 ft)

3.0 - 6.0 m

(9.8 - 19.7 ft)

2.0 - 3.5 m

(6.6 - 11.5 ft)

Max detection length Detection area

sensitivity

adjustment

12 m

8.5 m

6 m

3.5 m

2.5 m

-9-

NORM TEST

DIP switch 1

DIP switch 2

SWITCH SETTING

-WALK TEST MODE

VXI-R

VXI-RAM

VXI-RDAM

123456

POSITION FUNCTION

TEST

(Factory default)

NORM

The LED lights irrespective of the DIP switch 4 (LED)

setting.

The DIP switch 2 (BATTERY SAVING TIMER) setting is

inactive.

The LED lights depending on the DIP switch 4 (LED)

setting.

The DIP switch 2 (BATTERY SAVING TIMER) setting is

active.

Caution>>

After completing a walk test, always set the unit to NORM position for operation.

Using the unit in TEST mode will shorten the battery life.

120S 5S

-BATTERY SAVING TIMER

VXI-R

VXI-RAM

VXI-RDAM

123456

POSITION FUNCTION

120S

(Factory default)

5 sec.

120 sec.

Even if there are continuous alarm events, the alarm is generated only once

in the timer period to save the battery life.

PIR sensitivity selector

DIP switch

1 WALK TEST MODE

2 BATTERY SAVING TIMER

3 ALARM & TROUBLE OUTPUT

4 LED

5 ANTI-MASKING

6 MICROWAVE IMMUNITY

2 4 5 63

MW sensitivity adjustment

-10-

DIP switch 3

N.C. N.O.

-ALARM & TROUBLE OUTPUT

VXI-R

VXI-RAM

VXI-RDAM

123456

POSITION FUNCTION

N.O.

N.C.

(Factory default)

N.O. output

N.C. output

DIP switch 4

OFF ON

-LED

VXI-R

VXI-RAM

VXI-RDAM

123456

POSITION FUNCTION

OFF

(Factory default)

LED ON

LED OFF

Note>>

If the LED lights, check the DIP switch 1 (WALK TEST

MODE) setting.

DIP switch 5

OFF ON

-ANTI-MASKING

VXI-R

VXI-RAM

VXI-RDAM

123456

POSITION FUNCTION

OFF

(Factory default) ANTI-MASKING ON

ANTI-MASKING OFF

When masking condition continues more than 3 minutes, TROUBLE will be generated.

TROUBLE is generated after 20 seconds under the anti-masking test mode.

Teaching mode starts when both the separate box cover and the main unit cover are

attached.

Please be careful not to leave any object within 1 m from the unit.

<ANTI-MASKING function>

ANTI-MASKING test mode

The trouble is output after 20 seconds.

Normal mode

The trouble is output after 3 minutes.

10 minutes1 minute

Teaching

-11-

DIP switch 6

STD IMMUNITY

-MICROWAVE IMMUNITY

VXI-R

VXI-RAM

VXI-RDAM

123456

PIR SENSITIVITY SELECTOR

-PIR SENSITIVITY

VXI-R

VXI-RAM

VXI-RDAM

WALK TEST

123456

Note>>

The switch is set to “ON (TEST)” by factory default.

Note>>

The battery life will be shortened unless the DIP switch 1

is set to “OFF”.

HIGH

MIDDLE

LOW

POSITION FUNCTION

IMMUNITY

STD

(Factory default)

MICROWAVE IMMUNITY logic is activated. Use this under

harsh environment (e.g. vegetation sway).

MICROWAVE IMMUNITY logic is not activated.

POSITION FUNCTION

HIGH

MIDDLE

(Factory default)

High sensitivity

LOW Low sensitivity

Middle sensitivity

Note>>

For the walk test, make a motion at a distance more

than 1.0 m (3.28 ft) away from the detecter.

Detected Not

detected

Check that the cover is

completely closed.

1Set the DIP switch 1 (WALK TEST MODE) to “ON

(TEST)”. 2Attach the main unit cover.

3Check that LED lights for 2 seconds when the

intended object is detected. 4After completing the walk test set DIP switch 1 (WALK

TEST MODE) to “OFF (NORM)”.

-12-

LED INDICATION

RED YELLOW

(VXI-RDAM only)

Blink Light OFF

<VXI-R> <VXI-RAM>

<VXI-RDAM>

Detector condition LED indicator

Warm-up

Blinks for approx. 60 seconds.

Alarm

Lights for 2 seconds.

Masking detection

(VXI-RAM only)

Blinks 3 times and then repeats.

Note>>

The LED blinks even if the DIP

switch 4 (LED) is set to “OFF”.

Detector condition LED indicator

Warm-up

Blinks for approx. 60 seconds.

Alarm

RED LED lights for 2 seconds.

MW detection

YELLOW LED lights for 2 seconds.

Masking detection

Blinks 3 times and then repeats.

Note>>

The LED blinks even if the DIP

switch 4 (LED) is set to “OFF”.

RED YELLOW

-13-

BATTERY

The detector shares the battery with the transmitter. Check that the 2.5 – 10.0 VDC power battery is used for the transmitter.

The values indicated are only for reference on condition that the detector is exceptionally operated by the sole battery.

It is impossible to indicate the battery life under the normal operation as the battery in the transmitter is shared with the detector.

Black Red

6-1 HOW TO REPLACE BATTERY

6-2 BATTERY LIFE

Interval 120sec

VXI-R, VXI-RAM VXI-RDAM

Interval 5sec Interval 120sec Interval 5sec

Approx. 6 years Approx. 5 years

Approx. 4 years Approx. 3 years

CR123A (3 VDC, 1300 mAh)

CR2 (3 VDC, 750 mAh)

1/2AA (3.6 VDC, 1000 mAh)

Approx. 5 years Approx. 4 years

Approx. 4 years Approx. 3 years

Approx. 2 years Approx. 1 years

Approx. 3 years Approx. 2 years

Note>>

Data shown here is when the LED is off, AM is on. Battery life becomes shorter when the LED is on.

Note>>

Check that the warm-up period is started.

Red

Black

White

Yellow

Red

Black

White

Yellow

Green

Blue

Green

Blue

1By following the procedures 1 and 2 in "2-4 BEFORE MOUNTING", remove the cover and then remove the main

unit from the back box.

2Remove Power, Alarm and Trouble connectors, and

then remove the transmitter from the back of the

main unit.

3Replace the transmitter battery.

4By following the procedures 3 , 4 , 5 and 6 in "2-6 MOUNTING", mount the transmitter, connect the connector,

and then mount the main unit and cover.

-14-

SPECIFICATIONS

7-1 SPECIFICATIONS

VXI-RDAMVXI-RAMVXI-RModel

Passive infrared & MicrowavePassive infraredDetection method

12.0 m (40 ft) 90° wide / 16 zonesPIR Coverage

12 – 2.5 m (5 levels) PIR distance limit

0.3 – 1.5 m/s (0.98 – 4.92 ft/s)Detectable speed

2.0°C (3.6°F) at 0.6 m/sSensitivity

3 – 9 V DC (Lithium or Alkaline Battery)Power input

Current draw 9 μA (standby) / 4 mA (max.)

at 3 V DC

10 μA (standby) / 4 mA (max.)

at 3 V DC

18 μA (standby) / 8 mA (max.)

at 3 V DC

2.0 ±1 sec.Alarm period

Approx. 60 sec. (LED blinks)Warm-up period

N.C. / N.O. Selectable-Solid State Switch 10 V DC 0.01 A (max)

Alarm output

Trouble output

LED indicator

Disable: During normal operation.

Enable: During WALK TEST or LED SW on.

Red: Warm-up, alarm, masking detection (VXI-RAM only)

Disable: During normal operation.

Enable: During WALK TEST or LED SW on.

Red: Warm-up, alarm, masking detection.

Yellow: Warm-up, MW detect.

No alarm 10 V/mRF interference

-20 – +60°C (-4 – +140°F)Operating temperature

95% max.Environment humidity

IP55International protection

Wall, Pole (Outdoor, Indoor)Mounting

0.8 – 1.2 m (2.64 – 3.94 ft)Mounting height

500 g (17.7 oz.)Weight 600 g (21.2 oz.)

Accessories

Connector for POWER and ALARM, Connector for TROUBLE, Screw (4×20mm) ×2, Masking seal ×3

* Specifications and designs are subject to change without prior notice.

7-2 DIMENSIONS

Unit: mm (inch)

186 (7.32)

105.5 (4.15)

Pitch

=83.5

(3.29)

71.3 (2.81)

-15-

SETTING OF SPECIAL DETECTION AREA

Set to A or G

Using masking seals 2 to 6, you can set a special detection area for the horizontal position A or G.

Set to the desired area setting direction

(horizontal position A or G).

When setting other than masking

seal 1, cut off the knockout portion

at the lower lens holder.

Select a masking seal from 2 to 6

according to the desired shape of area

setting, and put it on the lens.

Masking seal 2

Masking seal 4

Masking seal 6

Masking seal 3

Masking seal 5

Area can be set only at the both sides.

Five patterns of special detection areas can be configured by

applying a masking sticker.

1.5 × 10 m area can be set.

10 × 1.5 m area can be set.

5 × 10 m area can be set.

10 × 5 m area can be set.

fghi

12 m 12 m

12 m

10 m 10 m

10 m

5 m 5 m

5 m

12 m 12 m

12 m

10 m 10 m

10 m

5 m 5 m

5 m

12 m 12 m

12 m

10 m 10 m

10 m

5 m 5 m

5 m

12 m 12 m

12 m

10 m 10 m

10 m

5 m 5 m

5 m

12 m 12 m

12 m

10 m 10 m

10 m

5 m 5 m

5 m

Position G Position A

Position G Position APosition G Position A

Position G Position A

The lower detection

area adjustment

position must be

“position 1” (12m) as

default.

-16-

OPTEX INCORPORATED (USA)

TEL:+1-909-993-5770

Tech:(800)966-7839

URL:http://www.optexamerica.com/

OPTEX KOREA CO., LTD. (KOREA)

TEL:+82-2-719-5971

URL:http://www.optexkorea.com/

OPTEX SECURITY Sp.z o.o. (POLAND)

TEL:+48-22-598-06-55

URL:http://www.optex.com.pl/

OPTEX (DONGGUAN) CO., LTD.

SHANGHAI OFFICE (CHINA)

TEL:+86-21-34600673

URL:http://www.optexchina.com/

OPTEX CO., LTD. (JAPAN)

(ISO 9001 Certified)

(ISO 14001 Certified)

5-8-12 Ogoto Otsu

Shiga 520-0101

JAPAN

TEL:+81-77-579-8670

FAX:+81-77-579-8190

URL:http://www.optex.co.jp/e/

OPTEX (EUROPE) LTD. (UK)

TEL:+44-1628-631000

URL:http://www.optex-europe.com/

OPTEX SECURITY SAS (FRANCE)

TEL:+33-437-55-50-50

URL:http://www.optex-security.com/

NOTE

COMPLIANCE

Note>>

These units are designed to detect an intruder and activate an alarm control panel. Being only a part of a complete

system, we cannot accept responsibility for any damages or other consequences resulting from an intrusion. These

products confirm to the EMC Directive 2004/108/EC.

• VXI series complies with following Directives / Standards.

Directive: EMC Directive 2004/108/EC

Applied Standards: EN 50130-4: 1995 +A1: 1998 +A2: 2003

EN 55022: 2006

• VXI-RDAM also complies with following Directives / Standards

marked Class II,

Directive: R&TTE Directive 1999/5/EC

Applied Standards: EN 300 440-1: 2009

EN 300 440-2: 2009

EN 301 489-1: 2008

EN 301 489-3: 2002

EN 50371: 2002

EN 60950-1: 2006 +A11: 2009

The following table indicates the areas of intended use of the equipment

and any known restrictions. For countries not included in this list,

please consult the responsible Spectrum Management Agency.

FCC ID: DC9 OPMWWL IC: 4012A-OPMWWL

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

Country of intended use

Austria

Belgium

Denmark

Finland

France

Greece

Ireland

Italy

Luxembourg

The Netherlands

Spain

Sweden

United Kingdom

Other non-EU: Iceland

Norway

Switzerland

13.700GHz

10.525GHz

13.700GHz

10.587GHz

10.525GHz

10.587GHz

10.525GHz

10.587GHz

10.525GHz

10,525GHz

Restrictions

Country of intended use

Restrictions

0700

Optex Infinity VXI-RDAM Installation Instructions Manual

Brand: Optex

Model: Infinity VXI-RDAM

Category: Motion detectors

Type: Installation Instructions Manual

This manual is also suitable for

Download PDF

report

Optex Infinity VXI-RDAM Installation Instructions Manual

This manual is also suitable for

Optex Infinity VXI-RDAM Installation Instructions Manual

Related papers

Other documents