V2 FLEXY2 User manual

Brand: V2

Model: FLEXY2

Category: Gate Opener

Type: User manual

Value moves the world

IL 384

EDIZ. 20/03/2014

FLEXY2

CENTRALE DI COMANDO ANALOGICA PER CANCELLI

A BATTENTE E SCORREVOLI

ANALOGUE CONTROL UNIT FOR LEAF SWING AND

SLIDING GATES

ARMOIRE DE COMMANDE ANALOGIQUE POUR

PORTAILS BATTANTS ET COULISSANTS

CUADRO DE MANIOBRA ANALÓGICO PARA CANCELAS

BATIENTES Y CORREDERAS

QUADRO ANALÓGICO PARA PORTÕES DE BATENTE

E PORTÕES DE CORRER

ANALOGSTEUERUNG FÜR FLÜGELTORE

UND SCHIEBETORE

ANALOGE BESTURINGSEENHEID VOOR DRAAIHEKKEN

EN SCHUIFHEKKEN

PROGRAMATOR ANALOGOWY DO BRAM SKRZYDŁOWYCH I

PRZESUWNYCH

ENGLISH

- 9 -

IMPORTANT REMARKS

For any installation problem please contact our Customer Service

atthenumber+39-0172.812411operatingMondaytoFriday

from8:30to12:30andfrom14:00to18:00.

V2 has the right to modify the product without previous

notice; it also declines any responsibility to damage or

injury to people or things caused by improper use or wrong

installation.

m Please read this instruction manual very carefully

before installing and programming your control unit.

• Thisinstructionmanualisonlyforqualiedtechnicians,who

specialize in installations and automations.

• Thecontentsofthisinstructionmanualdonotconcerntheend

user.

• Everyprogrammingand/oreverymaintenanceserviceshould

be done only by qualied technicians.

AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE

WITH THE EUROPEAN REGULATIONS IN FORCE:

EN 60204-1 (Machinerysafety.electricalequipment

     ofmachines,part1:generalrules)

EN 12445  (Safeuseofautomatedlockingdevices,test

     methods)

EN 12453  (Safeuseofautomatedlockingdevices,

     requirements)

• Theinstallermustprovideforadevice(es.magnetotermical

switch)ensuringtheomnipolarsectioningoftheequipment

fromthepowersupply.Thestandardsrequireaseparationof

thecontactsofatleast3mmineachpole(EN60335-1).

• Aftermakingconnectionsontheterminalboard,useone

hoseclamptoxdangerousvoltagewiresneartheterminal

boardandanotherhoseclamptoxsafetylowvoltagewires

usedforaccessoriesconnection;thisway,incaseofaccidental

detachmentofaconductingwire,dangerousvoltagepartswill

notcomeintocontactwithsafetylowvoltageones.

• TheplasticcasehasanIP55insulation;toconnectexibleor

rigidpipes,usepipettingshavingthesameinsulationlevel.

• Installationrequiresmechanicalandelectricalskills,thereforeit

shallbecarriedoutbyqualiedpersonnelonly,whocanissue

theComplianceCerticateconcerningthewholeinstallation

(EECMachineDirective2006/42/CEE,AnnexIIA).

• Theautomatedvehiculargatesshallcomplywiththefollowing

rules:EN13241-1,EN12453,EN12445aswellasanylocal

ruleinforce.

• Alsotheautomationupstreamelectricsystemshallcomplywith

thelawsandrulesinforceandbecarriedoutworkmanlike.

• Thedoorthrustforceadjustmentshallbemeasuredbymeans

ofapropertoolandadjustedaccordingtothemax.limits,

whichEN12453allows.

• Connecttheearthingleadofthemotorstotheelectricitygrid

earth system.

• Observeallnecessaryprecautions(e.g.anti-staticbracelet)for

handlingpartssensitivetoelectrostaticdischarges.

DECLARATION OF CONFORMITY

V2S.p.A.herebydeclarethatFLEXY2productsconformtothe

essentialrequirementsestablishedinthefollowingdirectives:

• 2004/108/CEE(EMCDirectiveinaccordancewithstandards

EN61000-6-2,EN61000-6-3+EN50336)

• 2006/95/CEE(LowVoltageDirectiveinaccordancewith

standardsEN60335-1+EN60335-2-103)

• 99/05/CEE(RadioDirectiveinaccordancewithstandard

EN301489-3)

• DirectiveROHS22011/65/CE

Racconigi,12/01/2013

V2S.p.A.legalrepresentative.egaledellaV2S.p.A.

Cosimo De Falco

TECHNICAL SPECIFICATIONS

Powersupply 230V/50Hz 120V/60Hz

Maxmotorsload 700W 700W

Maxaccessoriesload24V 3W 3W

Workingtemperature -20 ÷ +60 °C -20 ÷ +60 °C

Protectionfuse F1 = 5A delayed F1 = 8A delayed

Dimensions 170 x 185 x 70 mm

Weight 800g

Protection IP55

ENGLISH

- 10 -

DESCRIPTION OF THE CONTROL UNIT

TheFLEXY2controlunitisaninnovativeV2productguaranteeing

safetyandreliabilityforswinggateautomation.

TheFLEXY2designhasbeenaimedatcreatingaproductwhich

adaptstosuitallneeds,thusobtaininganextremelyversatile

controlunitsatisfyingallthenecessaryrequirementsfora

functionalandefcientinstallation.

• 230V-50Hzor120V-60Hzpowersupplies,dependingonthe

model,for2singlephasemotors(700Wglobal).

• Inputforkeyswitchorpush-button.

• Inputforsafetyphotocell.

• Inputforsafetyedge,capableofhandlingstandardedges

withswitchnormallyclosedandconductiverubberedgeswith

nominalresistanceof8.2kOhms.

• Inputsforopenandcloselimitswitches

• Pre-openingsafetydevicetesting.

• Dip-switchprogrammableoperationallogic.

• Adjustmentofmotorpowerandoperationtimebymeansofa

trimmer.

• Fitted433.92MHzradioreceiver

• Possibilityofsaving240PersonalPasstransmitters

(433.92MHz)

• LEDmonitoringofinputs.

• Courtesylightoutput.

• RJ45connectortoconnectthecontrolunittotheprogrammer

PROG2viastandardnetworkcable(UTP)

• IP55casing.

INSTALLATION

Installationofthecontrolunit,thesafetydevicesandaccessories

mustbeperformedwiththepowersupplydisconnected.

POWER SUPPLY

Thecontrolunitmustbepoweredbymeansofa230V-50Hz

or120V-60Hzpowerline,dependingonthemodel,protected

byadifferentialmagnetothermalswitchincompliancewithlegal

regulations.

ConnectthepowercablestothecontrolunitL and N terminals.

MOTORS

ThecontrolunitcancontroloneortwoasynchronousACmotors.

Ifthecontrolunitisusedtocontrolonlyonemotor,thenthis

mustbeconnectedtotheterminalsrelatingtomotor1.

Connectthecablesformotor1asfollows:

• OpeningcabletoterminalK3

• ClosingcabletoterminalK5

• CommonreturncabletoterminalK4

• Start-upcapacitorbetweenterminalsK3 and K5

Connectthecablesformotor2(ifpresent)asfollows:

• OpeningcabletoterminalK6

• ClosingcabletoterminalK8

• CommonreturncabletoterminalK7

• Start-upcapacitorbetweenterminalsK6 and K8

PHOTOCELLS

Thecontrolunithasa24VACpowersupplyforphotocellswith

switchnormallyclosed,andcanperformanoperationaltest

beforetostartingthegateopeningprocedure.

Thephotocellcanbeusedwithtwosettings:

1. Photocell always active:

Interventionofthephotocellduringopeningorclosingcauses

thegatetostop.Whenthephotocellrestores,thegatere-

opens completely.

2. Photocell NOT active during opening:

Interventionofthephotocellduringopeningisignored.

Interventionofthephotocellduringclosingcausesthegateto

re-open completely.

Independentlyofthesettingselected,whenthegateispaused

whileopening,thetimecountforanyautomaticre-closurewill

onlystartafterthephotocellrestores.

• Connectthephotocelltransmitterpowercablesbetween

terminals L10 (GND)andL11 (+)onthecontrolunit.

• Connectthephotocellreceiverpowercablesbetweenterminals

L10 (GND)andL9 (+)onthecontrolunit.

• ConnectthephotocellreceiveroutputbetweenterminalsL4

and L8 on the control unit.

SAFETY EDGES

Thecontrolunithasaninputforcontrollingsafetyedges;this

inputiscapableofcontrollingstandardedgeswithswitch

normallyclosedandconductiverubberedgeswithnominal

resistanceof8.2kOhms.

Edgescanbeusedwithtwosettings:

1. Edge always active:

Interventionoftheedgeduringopeningorclosingcauses

inversionofthedirectionofmovementinordertofreethe

bodythatcausedtheedgetointervene.Thegatestopsafter

approx. 3 seconds.

2. Edge NOT active during opening:

Interventionoftheedgeduringopeningisignored.

Interventionoftheedgeduringclosingcausesthegateto

re-open completely.

Independentlyofthesettingsselected,anysubsequentautomatic

re-closurewillbecancelled.

Standard edge with switch normally closed: connecttheedge

cablesbetweenterminalsL5 and L8 on the control unit.

InordertosatisfytherequirementsofstandardEN12978,it

isnecessarytoinstallsafetyedgeswithacontrolunitwhich

constantlymonitorscorrectoperation.Ifcontrolunitsareused

withtheoptionofrunningtestsbymeansofinterruptingthe

powersupply,connectthecontrolunitpowersupplycables

betweenterminalsL10(GND)andL11(+).

Conductive rubber edge:connecttheedgecablesbetween

terminalsL5andL8onthecontrolunit.

m PLEASE NOTE: operational testing on edges is

reserved for standard edges (only if equipped with suitable

control units).

DO NOT enable testing if conductive rubber edges are used

or standard edges used without a suitable control unit for

controlling function.

ENGLISH

- 11 -

COURTESY LIGHT

Thisoutputhasanormally-opencleancontactrelaywhichcloses

forapprox.1secondatthestartofanopeningphase.

Thisswitchmaybeusedtoactivateacourtesylighttimer(max.

load:230V-4A).

TheswitchisonterminalsK1 and K2.

BLINKER

Thecontrolunitprovidesfortheuseofa230V-40Wor

120V-40Wblinkerwithbuilt-inintermittence.

Connect the cables to terminals K9 and K10.

START INPUT

TheSTARTinputispresetforconnectingdeviceswiththeswitch

normally open.

Functiondependsonthemodeofoperationsetbymeansofdip-

switch4.

Step mode

Subsequent Start command cause, in order:

openingg stop g closure g stop

“Inversion” mode

Startduringopeningcausesclosure.

Startduringclosurecausesopening.

Startwiththegateopenalwaysresultsinclosure;the only case

wherethisdoesnotoccurimmediatelyiswhenautomaticclosure

isenabledandstartwhileopeningisnotaccepted:inthisspecic

case,startmakesthepausetimecountstartfromzero,after

whichthegatewillbere-closed.

InbothmodesitispossibletodisabletheStartcommandduring

gateopeningbymeansof

dip-switch3.

Connectthestartinputcontroldevicecablesbetweenterminals

L1 and L8 on the control unit.

PEDESTRIAN START

Withthegateclosed,thepedestrianstartcommandcausespartial

opening(approx.halfway)ofthegateleafconnectedtomotor1.

Subsequentpedestrianstartcommandswillfunctionaccordingto

steplogic.

Duringapedestriancycle,thestartcommandresultsinthe

completeopeningofbothgateleaves.

Connectthepedestrianstartinputcontroldevicecablesbetween

terminals L2 and L8 on the control unit.

STOP

TheSTOPinputisintendedfordeviceswiththeswitchnormally

closed.

TheSTOPcommandcausestheimmediatestopofthegate.

AsubsequentSTARTcommandactivatesthegateintheopposite

directionofmovement.

IftheSTOPcommandisgivenduringopeningorpause,then

therewillbenosubsequentautomaticre-closure.

Connectthestopinputcontroldevicecablesbetweenterminals

L3 and L8 on the control unit.

LIMIT SWITCH INPUTS

Thecontrolunitisconguredforconnectingaswitchwithswitch

normallyclosed,whichisopenedwhenthegatereachesthe

desired position.

Connectthelimitswitchcablesasfollows:

• ClosinglimitswitchbetweenterminalsL6 and L8

• OpeninglimitswitchbetweenterminalsL7 and L8

EXTERNAL ANTENNA

Itisrecommendedtheexternalantennabeusedinorderto

guaranteemaximumradiocapacity.

Connect the antenna hot pole to terminal A1ofthecontrolunit

andthebraidingtoterminalA2

ENGLISH

- 12 -

ANT

START

STOP

START P.

PHOTO

EDGE

FCA

FCC

COM

POWER

J1 WORK PAUSE DELAY

1 2 3 4 5 6 7 8 9 10 11 12

START START P.

STOP

PHOTO

L1 L2

A1 A2

L3 L4 L5 L6 L7 L8 L9 L10 L11 K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 N Lmains

EDGE

FCA

FCC

overload

mains

PROG.RX

RJ45

(Photo / Edge Test)

COURTESY

LIGHT

CONTACT

ELECTRICAL CONNECTION

m PLEASE NOTE: If not used, the normally closed inputs (STOP, PHOTO, EDGE, FCA, FCC) must be jumpered with the

commands common line COM (-)

ENGLISH

- 13 -

A1 Antenna

A2 Antenna shield

L1 Openingcommandforastandardconnectiondevice

withswitchnormallyopen.

L2 Pedestrianopeningcommandforastandard

connectiondevicewithswitchnormallyopen.

L3 STOPcommand.N.C.switch

L4 Photocell.N.C.switch

L5 Edge.SwitchN.C.orresistiverubberedge

L6 Limitswitchopen.N.C.switch

L7 Limitswitchclosed.N.C.switch

L8 Commandscommon(-)line

L9 - L10 24VACpoweroutputforphotocellsandother

accessories

L10 - L11 PowersupplyforfunctionaltestTXphotocell

K1 - K2 Courtesylighttimeractivationswitch

K3 Motor1open

K4 Motor1common

K5 Motor1close

K6 Motor2open

K7 Motor2common

K8 Motor2closed

K9 - K10 230V - 40W / 120V - 40W blinker

N230V/120Vpowersupply-neutral

L230V/120Vpowersupply-phase

CABLE GLAND ASSEMBLY

Thecasingcanaccept4cableglandsinthespecialeasy-break

housings.

Thetypeofcableglandisindicatedinthegure.

m PLEASE NOTE:

• Removetheelectroniccircuitboardbeforedrillthecasing.

• Drillthecontainerusingasuitablysizedcutter,accordingtothe

dimensionsofthecablegland.

• Fixthecableglandsusingthespecialnuts.

PG9 - PG11

PG9 - PG11 - PG16

ENGLISH

- 14 -

DIP FUNCTION SETTING DESCRIPTION

1Pre-ashing ON Disabled Theblinkerisswitchedonwhenthemotorsarestarted

OFF Enabled Theblinkerisswitchedonfor2secondsbeforethemotorsarestarted

2Automatic closure

ON Enabled ThegateisclosedautomaticallyaftertheperiodoftimesetbythePAUSE

trimmer

OFF Disabled Oncompletionoftheopeningstep,thegateremainsopen.Itisnecessaryto

instructclosurewithanotherSTARTcommand

3Startduring

opening

ON Not accepted AnySTARTcommandissuedduringopeningisignored

OFF Accepted AnySTARTcommandissuedduringopeningisaccepted

4Operationallogic

ON Inversion Startduringopeningcausesclosure.

Startduringclosurecausesopening.

OFF Step Commandssubsequenttostartingcause,inorder:

open g stop g close g stop...

5Slowdown

ON Enabled Attheendofeachopeningandclosingstep,themotorsslowdowninorder

toavoidnoisyclosureandbouncing.

OFF Disabled

6Startoff ON Disabled Atthestartofeachopeningandclosingstep,themotorsarestartedat

maximumpower

OFF Enabled

7Anti-slip

ON Disabled ThetimeusedforopeningorclosurewillalwaysbethevaluesetbytheWORK

trimmer,evenifthepreviousoperationhasbeeninterruptedbeforetheexpiry

ofsuchtime.

OFF Enabled Whenanopening(orclosing)operationisinterruptedbeforeexpiryofthe

settime(forexampleduetotheinterventionofoneofthesafetydevicesor

duetoastartcommand),thedurationofthesubsequentclosing(oropening)

operationwillnotbethatsetbytheWORKtrimmer,butwillbeequaltothe

timeeffectivelyelapsed,plusashortsupplementaltimeinordertocompensate

fortheinertiaofthegate.

8Photocell

ON Alwaysactive Interventionofthephotocellduringopeningorclosingcausesthegateto

stop.Whenthephotocellrestores,thegatere-openscompletely.

OFF NOTactiveduring

opening

Interventionofthephotocellduringopeningisignored.Interventionofthe

photocellduringclosingcausesthegatetore-opencompletely.

9Photocell test

ON Enabled Thecontrolunitperformsaphotocelloperationaltestbeforestartingeach

openingorclosingoperation.Ifthephotocellsarenotoperatingcorrectly,the

gatedoesnotbegintomoveandthelightashesforapprox.8seconds.

PLEASE NOTE: connect the photocell TX correctly

OFF Disabled

10 Safetyedgetype

ON Conductive rubber

edge

Selectthisoptionifusingconductiverubberedgeswithnominalresistanceof

8K2.

OFF Standard or optical

edge

Selectthisoptionifusingstandardedgeswithswitchnormallyclosedor

opticaledges.

11 Safetyedge

ON Alwaysactive Interventionoftheedgeduringopeningorclosingcausesinversionofthe

directionofmovementinordertofreethebodythatcausedtheedgeto

intervene.Thegatewillbestoppedafterapprox.3seconds.

OFF NOTactiveduring

opening

Interventionoftheedgeduringopeningisignored.Interventionoftheedge

duringclosingcausesthegatetobere-openedcompletely.

12 Safetyedgetest

ON Enabled Thecontrolunitperformsanoperationaltestontheedgesbeforestarting

eachopeningorclosingoperation.Iftheedgesarenotoperatingcorrectly,the

gatedoesnotbegintomoveandthelightashesforapprox.8seconds.

DO NOT enable testing if conductive rubber edges are used or standard

edges are used without a suitable control unit for controlling function.

OFF Disabled

PROGRAMMING THE OPERATIONAL LOGIC

Itispossibleforthecontrolunittouseseveraldifferentoperationallogicstates,bysimplymovingthedip-switcheslocatedonthecard.

Thefunctionsassociatedwitheachindividualdip-switcharelistedbelow.

ENGLISH

- 15 -

ADJUSTMENT OF THE POWER AND

OPERATIONAL TIMES

Thepowerandoperatingtimesmaybeadjustedbymeansof4

trimmers located on the control unit:

m PLEASE NOTE: it is recommended that operating times

be set with the slow down function disabled (DIP 5 OFF).

m WARNING: the adjustment of times has to be made

when the gate is still

CONTROL UNIT INDICATORS (LEDs)

ThehighlightedboxesindicatethestateoftheLEDswhenthegateisresting.

LED ON OFF

START STARTinputclosed STARTinputopen

START P. STARTP.inputclosed STARTP.inputopen

STOP STOPinputclosed STOPinputopen

PHOTO PHOTOinputclosed PHOTOinputopen

EDGE Standard edge

EDGEinputclosed(edgenotpressed) EDGEinputopen(edgepressed)

Resistive rubber edge

EDGEinputclosed(edgepressed) EDGEinputopen(fault)

EdgeNOpressed:8K2betweenEDGEinputand

common(-)

FCA Openinglimitswitchclosed Openinglimitswitchopen

FCC Closinglimitswitchclosed Closinglimitswitchopen

mains Controlunitpowered-up ControlunitNOTpowered-up

overload Accessorypowersupplyoverload Accessorypowersupplywithinnormaloperationallimits

POWER:  motorpower.

WORK:   motoroperatingtime

     J1closed=2-50seconds

     J1opened=2-120seconds

PAUSE:   pausetimebeforeautomaticre-closure

     (2-150seconds).

DELAY:   timedelaybetweenthetwogateleaves

     (0-90seconds).

POWER

MIN MAX

WORK 120”

30”

2”

90”

WORK 50”

18”

2”

45”

PAUSE 150”

30”

2”

90”

DELAY 90”

15”

45”

J1 closed J1 opened

J1 opened J1 closed

ENGLISH

- 16 -

STORING OF THE TRANSMITTERS

• KeepPROG.RXpresseduntiltheledL1lightens

• Releasethepush-button,theledswitchesoffanditsendsout

asequenceofsingleashingsfor5seconds:thenumberof

shortashingsshowstheselectedchannel

• ToselectthefurtherchannelspressandreleasethePROG.RX

push-buttonwithin5seconds,theledchangestypeofashing

accordingtothefollowingtable:

FULL ERASING of the TRANSMITTERS

Toperformafullerasingofthetransmittersstoredinmemorydo

thefollowing:

• Switchoffthepowersupplyofthecontrolunit,

• PressandholdpressedthePROG.RXkeyofthereceiver

• Atthesametimeturnonthepowersupplyagain.TheL1led

goeson

• ReleasethePROG.RXkey:theledL1remainsonforthe

durationoftheerasingphase(about5seconds)

• WhentheledL1turnsofftheerasingprocedureiscomplete

andthecontrolunitisreadyforanewprogramming

To perform a partial code erasing the PROG2 portable

programmer is required

ROLLING CODE FUNCTION

ItispossibletoenableandtodisabletheROLLINGCODEfunction

(normallydisabled)

• PressPROG.RXpush-button,holdingitfor8seconds.

• L1ledwillswitchoffafter8seconds.Releasethepush-button.

• L1ledstartsasequenceofashingfor5seconds:

 Singleashings g ROLLINGCODEisdisabled

Doubleashings g ROLLINGCODEisenabled

• TomodifytheparameterspressthePROG.RXpush-button

within5secondsaftertherstashingofthesequence;L1led

willashaccordingtothenewparameters.

SUBSITUTIVE TRANSMITTER

Thesubstitutivetransmitter,generatedonlybymeansof

WINPPCL,allowstoreplacebyradioatransmitterstoredinthe

receiver.

Asingletransmissionwiththespeciallyprogrammed

SUBSTITUTIVETX,nearbythereceiver,replacesthetransmitter

codewiththenewone.

RepeattheprocesswithallkeysoftheSUBSTITUTIVETX.

Example:MemorizedTXAtransmitter

Itispossibletomakethreereplacementsmaximumpercode,so

forTXAyoucannd:

TXBreplacesTXA(TXAisnolongeroperative)

TXCreplacesTXB(TXBisnolongeroperative)

TXDreplacesTXC(TXCisnolongeroperative)

• Choosethechannelyouwanttomemorizeandwithin5

secondspressandholdthepush-buttonofthetransmitter.

• TheledL1switchesoffanditswitchesonagain:thismeans

that the code has been memorized.

• Thedevicewillwaitforafurthercodetomemorizefora

maximumtimeof5seconds.

SELECTED

CHANNEL

FUNCTION N° Impulses

PROG.RX

Flashing

single double triple quadruple

CHANNEL1 START 1•

CHANNEL2 PEDESTRIANSTART 2••

CHANNEL3 STOP 3•••

CHANNEL4 COURTESYLIGHT 4••••

V2 FLEXY2 User manual

Brand: V2

Model: FLEXY2

Category: Gate Opener

Type: User manual

Download PDF

report

V2 FLEXY2 User manual

V2 FLEXY2 User manual

Related papers

Other documents