Badger Basket 00362 Assembly And Use Instructions

Type
Assembly And Use Instructions
5.0/0518/HF
FOLDING DOLL CRADLE -
PINK ROSEBUD
MODEL NUMBER*:
00362
Assembly and Use Instructions. Adult assembly Required.
Read all instructions before use.
This manual is part of the product and
must be saved for future reference.
VERSION CODE*:
5.0/0518/HF
* Model and Version numbers are needed
if replacement parts are requested
Badger Basket Company, PO Box 227, Edgar, WI 54426-0227 USAWeb: www.badgerbasket.com
U.S. Based Customer Service Toll-Free (Mon-Thurs 7:00 AM-4:00 PM CST): 1-800-236-1310
Phone: 715-352-2311 • Fax: 715-352-3163
FOR REPLACEMENT PARTS:
http://www.badgerbasket.com/parts
5.0/0518/HF
BEFORE YOU BEGIN ASSEMBLY:
Check all parts. If anything is missing or not
satisfactory, please DO NOT call the store
or return the product to them. Please go online to:
http://www.badgerbasket.com/parts
Most problems are resolved
without you needing to leave home.
When contacting us, please have this
instruction manual, your product model number,
and your Version Code ready.
Your Model Number is: 00362
Your Version Code is: 5.0/0518/HF
WARNING - CAUTION
WARNING
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS AND SHARP
POINTS DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS before use of this product. Use only the parts and
hardware provided by Badger Basket. Keep instructions for future use. Do not use the
product if it is damaged or broken. Periodically inspect the product to ensure all parts
remain tight. This item is a toy for dolls only. It is never to be used for real infants or
pets. No product is a substitute for adult supervision. Always supervise your child
during play. For children ages three (3) years and older. Never sit on or stand on the toy.
CARE INSTRUCTIONS:
Frame can be wiped clean with a damp cloth and mild soap and dry thoroughly.
Spot clean or hand wash fabric as needed with cold water and mild detergent
and allow to air dry.
5.0/0518/HF
TOOLS NEEDED:
Phillips Screwdriver
(not included)
PARTS INCLUDED:
(A) 1 x CRADLE BODY
(B) 1 x LONG METAL ROD
(C) 2 x METAL ROCKERS
(D) 4 x BOLTS
(E) 1 x PADDED MAT
PARTS AND HARDWARE
Ax1
Ex1
Cx2
Bx1
Dx4
5.0/0518/HF
STEP 1: See PICTURE 1. Assemble the cradle base as shown using the CRADLE BODY (PART A), LONG
METAL ROD (PART B), TWO METAL ROCKERS (PART C), and FOUR BOLTS (PART D).
STEP 2: See PICTURES 2A and 2B.Turn the cradle right side up. Unfold the metal frame support bars inside
the CRADLE BODY (PART A) and apply pressure to snap them under the plastic clips that are attached to the
bottom board.
STEP 3: See PICTURE 3. Place the PADDED MAT (PART E) inside the cradle body. Next, secure the hood in
the open position by pressing on the hinge bars to lock into place. The cradle is ready for play!
A
B
C
PICTURE 1
C
D
D
D
D
PICTURE 2A
PICTURE 2B
E
Hinge Bar
PICTURE 3
When play time is over, the hood hinge bars can be
released to collapse the hood; and the metal
support bars inside the cradle can be released to
collapse the cradle body for storage or travel.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Badger Basket 00362 Assembly And Use Instructions

Type
Assembly And Use Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI