Pacic Accessory Corporation
®
| Ph. 866-931-8021 | [email protected]
©2015 Pacic Accessory Corporation
www.pac-audio.com
Pacific Accessory Corporation
Rev. 092115
Page 1
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
Arbitration
EOD
CRC
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
Radio Replacement Interface
with Nav Outputs for
Chrysler / Dodge / Jeep Vehicles
With or Without Premium Audio Systems
LCCH11/LCCH21
1. Vehicles without a factory amplier: Connect the aftermarket radio’s front and
rear speaker wires to the 22 pin plug.
2. Vehicles with a factory amplier: Connect the front outputs of the
aftermarket radio to the rear inputs of the 22 pin radio connector. This will allow
navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs
of the aftermarket radio are not used. The factory amplier only accepts two audio
channels (left and right). The amplier’s fading is controlled by data communication
from the factory radio. The aftermarket radio does not have the ability to control the amplier’s fader.
3. The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory
wire. The accessory wire supplies +12v, 1 amp max when key is in the accessory or ignition position (g. 1: If more current is
needed).
4. 11 pin plug (to CAN INTERFACE):
• Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp
present! This connection is VERY IMPORTANT! Some of the LCCH11/
LCCH21 features will not function if this wire is not connetced!
• White/Green - SWC output.
• Green - Connect this wire to the radio’s reverse input wire only.
• Orange/White - Connect this wire to the radio’s Illumination input wire only.
• Violet/White - Connect this wire to the radio’s VSS input wire only.
• Red/White - Connect this wire to the radio’s parking brake input wire only.
Note: Do not connect these wires to any circuit other than the radio’s wire harness.
5. 11 pin plug (to SWC INTERFACE): This is a quick connection to a radio
specic SWC interface. No additional connections are necessary other than
radio control connections. Plug the radiospecic SWC interface in to this
connector and program the radio specic SWC interface for version 2. Do not
cut the loops. Refer to the SWC interface instruction manual for the radio specic control function programming order.
Fig. 1
(using a SPDT relay)
85 86
30
87
87a
Ground
High Current 12v
(Fused)
12v Acc.
From
Interface
New High
Current Output
Diode 1N4005
or equivelant
9
1
23456
78
1011
Accessory Output
+12volts 1amp max.
Pacific Accessory Corporation
Chrysler Radio Replacement Interface
2005 & up
9 1
9
1
23456
78
1011
9 1
SWC Interface.
Program for Version 2
Radio Specific Steering
Wheel Control Interface
(Sold Separately)
Program SWC
Interface for Version 2.
CAN INTERFACE
Navigation outputs and
Amplifier Remote Input
See Chart for wire color
descriptions.
Radio Connections. See aside
Chart for color description.
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
(Read the Installation Notes before making
connections to the provided radio harness)
CAN Interface Connection Chart:
Red Acc. Output (1 amp)
Red / White P.B. Output (-)
Purple / White VSS Output (Pulse)
Orange / White Illum. Output (+)
Green Reverse Output (+)
White / Green SWC Output
Blue / White Amp Turn On Input
Installation Notes
Radio Connection Chart
Pacic Accessory Corporation
®
| Ph. 866-931-8021 | [email protected]
©2015 Pacic Accessory Corporation
www.pac-audio.com
Pacific Accessory Corporation
Rev. 092115
Page 2
Using the VES & Reverse Camera (if equipped)
PLEASE NOTE: The CHYRVD cable is sold seperately
Vehicles equipped with a DVD player built into the rear screen assembly:
The LCCH11/LCCH21 will allow the VES DVD player and rear screen to function as if the factory radio were present. A/V will be
passed from the factory DVD player to the rear screen and audio can be heard through the headphones. A/V cannot be passed
from the factory DVD player to the aftermarket head unit.
Vehicles equipped with a stand alone VES DVD Player:
The LCCH11/LCCH21 will allow the VES DVD player and rear screen(s) to function as if the factory radio were present. A/V will be
passed from the factory DVD player to the rear screen(s) and audio can be heard through the headphones. A/V can also be fed
from the VES DVD player into an aftermarket head unit (head unit must support A/V in) with the use of the CHYRVD. It is VERY
IMPORTANT that the LCCH11/LCCH21 Blue/White remote input wire be connected for this feature to function properly!
Vehicles not equipped with a VES DVD Player (rear screen(s) only):
In this application the CHYRVD must be used in order to feed A/V into the factory screen(s) from an aftermarket head unit (head
unit must support A/V out). With the CHYRVD, A/V will be passed from the aftermarket head unit to the rear screen(s) and audio
can be heard through the headphones. If you wish to retain the Auxiliary inputs on the rear of the console you must disconnect the
factory wires from the auxiliary input then connect and run your own RCAs into the aftermarket head unit.
Vehicles equipped with a Reverse Camera:
In order to retain the factory reverse camera the CHYRVD must be used to feed video into the aftermarket head unit (head unit
must support reverse camera input).
/
