Rugged Ridge Aluminum Hood Catch Installation guide

Brand
Rugged Ridge
Model
Aluminum Hood Catch
Type
Installation guide

This manual is also suitable for

Rugged Ridge 11116.07

The Rugged Ridge 11116.07 is a Jeep JK Aluminum Hood Catch that is intended to supplement the Jeep-supplied latch at the front of the hood. It is designed to provide additional security and prevent the hood from accidentally opening while driving. The hood catch is made of aluminum and is easy to install. It comes with all necessary hardware and instructions.

Here are some of the features and benefits of the Rugged Ridge 11116.07:

  • Made of aluminum for strength and durability
  • Easy to install with included hardware
  • Provides additional security and prevents the hood from accidentally opening

Rugged Ridge 11116.07

The Rugged Ridge 11116.07 is a Jeep JK Aluminum Hood Catch that is intended to supplement the Jeep-supplied latch at the front of the hood. It is designed to provide additional security and prevent the hood from accidentally opening while driving. The hood catch is made of aluminum and is easy to install. It comes with all necessary hardware and instructions.

Here are some of the features and benefits of the Rugged Ridge 11116.07:

  • Made of aluminum for strength and durability
  • Easy to install with included hardware
  • Provides additional security and prevents the hood from accidentally opening
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Page 1/3
11116.07 (Silver)
11210.11 (Black)
JEEP® JK ALUMINUM HOOD CATCH
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
Contents:
• A - Latch
• B - Latch Joint
• C - Pivot Base Joint
• D - Pivot Base
• E - Catch
• F - Pivot Base Gasket
• G - Catch Gasket
• H - Flat Head Bolts
• I - Lock Nuts
• J - Binding Posts
• K - Jam Nuts
• L - Adjustment Rod
• M - Safety Snap
Suggested Tools:
• Basic Hand Tools
A
B
C
D
E
F
G
H
I
J
M
J
J
J
K
L
PATENT PENDING
• Assure hood is fully secure by undamaged Jeep® front latch & supplemental side
catches.
• Do not modify hood or catches to defeat intended safety of Jeep® primary latch &
supplemental catch system.
Hood catch is intended only as supplemental to Jeep® supplied latch at front of hood.
To avoid risk of property damage or injury: Always;
CAUTION
!
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Page 2/3
Figure 1
Figure 1
Figure 1
Figure 1
2. Pull/remove the hood bumper from the factory hood catch.
1. Remove the factory hood catch.
3. Remove the pivot base from the Aluminum Hood Catch
assembly.
4. Attach the hood bumper (Removed in Step 2) to the pivot
base.
11116.07 (Silver)
11210.11 (Black)
JEEP® JK ALUMINUM HOOD CATCHPATENT PENDING
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Figure 1
Figure 1
Figure 1
6. Re-attach the Aluminum Hood Catch assembly to the
pivot base using the binding posts removed in Step 3.
5. Fasten the catch to the hood. Fasten the pivot base to the
fender.
Be sure safety snap is securely attached to catch.
7.AdjusttheAluminumHoodCatchbyrstreleasingthelatch.
With jam nuts loose, rotate latch clockwise to increase tension or
counter clockwise to decrease tension. When adjusted properly,
hood should contact and slightly compress the hood bumper.
Be sure adjustment rod has thread engagement
equal or greater to 3 threads on each end. Operating vehicle with
inadequate thread engagement could result in damage to
vehicle.
8. Your Aluminum Hood Catch is installed and road ready!
Page 3/3
11116.07 (Silver)
11210.11 (Black)
NOTICE
NOTICE
JEEP® JK ALUMINUM HOOD CATCHPATENT PENDING
  • Page 1 1
  • Page 2 2
  • Page 3 3

Rugged Ridge Aluminum Hood Catch Installation guide

Brand
Rugged Ridge
Model
Aluminum Hood Catch
Type
Installation guide
This manual is also suitable for

Rugged Ridge 11116.07

The Rugged Ridge 11116.07 is a Jeep JK Aluminum Hood Catch that is intended to supplement the Jeep-supplied latch at the front of the hood. It is designed to provide additional security and prevent the hood from accidentally opening while driving. The hood catch is made of aluminum and is easy to install. It comes with all necessary hardware and instructions.

Here are some of the features and benefits of the Rugged Ridge 11116.07:

  • Made of aluminum for strength and durability
  • Easy to install with included hardware
  • Provides additional security and prevents the hood from accidentally opening
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers