Hawk® Performance HTC4208, HB103P.590, HB103Y.590, HB675Y.602, HTC4202, HTC4203, HTC4237, Talon Cross Drilled and Slotted Brake Rotors Installation guide

  • Hello, I'm your chat assistant. I've reviewed the Hawk Performance brake pad installation and bed-in instructions, including procedures for Street, Motorsports, and Motorcycle brake pads. The document provides detailed steps for rotor preparation, pad installation, and proper bed-in procedures specific to each application. I am ready to answer any questions you have about this document.
  • What grit sandpaper should I use to clean the rotor surface?
    What should I do if my rotors have deep grooves?
    How long should I let the brake system cool down after the street brake bedding-in process?
    How should i bed in Motorcycle Metallic Brake pads?
    What should I do if the brake pedal becomes soft during the bed-in procedure for Motorsports brake pads?
  PADINSTALLATIONAND
BED‐ININSTRUCTIONS
STREET
Installationinstructionsshouldbefollowedinaccordancewiththeapplication‐specificbrakepad
installationinstructionsprovidedbythevehiclemanufacturer.
BrakePadInstallationProcedure
Installbrakepadsproperly.Besurepadsaresecurelypositionedinthecaliper.
CheckBrakeFluid.Flushandreplace,asneeded.
Checkallhydraulicpartsforexcesswearandtear.
Checkrotorfordeepgroovesorscoring.Resurfaceorreplacerotor,asneeded.
Ifrotorsdonotneedresurfacing,thencontaminationfromthepreviousbrakepadsmustbe
removed.Sandrotorswith130‐gritsandpaperusingmoderatepressure.Usesoapandwaterto
cleanrotorsurfaceaftersanding.Rotorsshouldbefreeandclearofoil,greaseandbrakefluid.
Inspectcalipersforfreedomofmovement.Lubricatewherenecessary.
StreetBrakePadBurnishing/Bedding‐InInstructions
1. Tobreakinthenewcomponents,make6to10stopsfromapproximately30to35MPH
applyingmoderatepressure.
2. Makeanadditional2to3hardstopsfromapproximately40to45MPH.
3. DONOTDRAGBRAKES!
4. Allow15minutesforbrakesystemtocooldown.
5. Yourbrakesarenowreadyforuseandcanbedrivennormally.
  PADINSTALLATIONAND
BED‐ININSTRUCTIONS
MOTORSPORTS
Installationinstructionsshouldbefollowedinaccordancewiththeapplication‐specificbrakepad
installationinstructionsprovidedbythevehiclemanufacturer.
BrakePadInstallationProcedure
Installbrakepadsproperly.Besurepadsaresecurelypositionedinthecaliper.
CheckBrakeFluid.Flushandreplace,asneeded.
Checkallhydraulicpartsforexcesswearandtear.
Checkrotorfordeepgroovesorscoring.Resurfaceorreplacerotor,asneeded.
Ifrotorsdonotneedresurfacing,thencontaminationfromthepreviousbrakepadsmustbe
removed.Sandrotorswith130‐gritsandpaperusingmoderatepressure.Usesoapandwaterto
cleanrotorsurfaceaftersanding.Rotorsshouldbefreeandclearofoil,greaseandbrakefluid.
Inspectcalipersforfreedomofmovement.Lubricatewherenecessary.
MotorsportsBrakePadBurnishing/Bedding‐InInstructions
1. Afterreachingmediumspeedengagebrakepedaltoslowcarwithoutcomingtoacomplete
stop.Releasepedalquicklyanddonotdragbrakes.Repeatfourorfivetimes.
2. Athigherspeedsengagebrakepedaltoslowcarwithoutcomingtoacompletestop.Release
pedalquicklyanddonotdragbrakes.Repeatfivetimes.
3. Atornearracespeedengagebrakepedaltoslowcarwithoutcomingtoacompletestop.
Releasepedalquicklyanddonotdragbrakes.Repeatthreetimes.Allowafewsecondsbetween
brakeengagementswhilecarisinmotion.
4. Donotholdbrakepedal.Parkcarforapproximately20minutesoruntilbrakerotorsare
completelycooltothetouch.
5. Ifduringtheabovestepsthebrakepedalbecomessoftorbrakefadeisnoticed,parkthecar
immediatelyforapproximately20minutes.Donotholdbrakepedal.
IMPORTANTREMINDERSWHENBURNISHING/BEDDINGBRAKEPADS
Donotattempttousebadlywornordamagedrotorswithnewbrakepads.
Donotdragbrakeswhilecarismovingduringbreak‐inprocedure.
Donotengagepedalwhilecarisstoppedatanytimefollowingthebreak‐inprocedure.
Uponcompletingtheprocedure,allowthebrakesystemtocompletelycoolbeforeracing.
Applyingthepedalafewtimesbeforethestartoftheracewillallowthebrakepadstoheatup
beforeattemptingtoreachracespeeds.
Cleanausedrotorsurfacewithfinesandpaperorsteelwool,rinsewithwater,dryandinstall
beforebeddingnewpads.
Someformsofracingdon’tallowtimefortheproperbreak‐inproceduretobeperformed.
However,itisstillveryimportanttoattempttoperformatleastthecoreoftheprocedure:Build
upheatslowlyandallowthesystemtocompletelycooldownbeforeracingifpossible
  PADINSTALLATIONAND
BED‐ININSTRUCTIONS
MOTORCYCLE
Installationinstructionsshouldbefollowedinaccordancewiththeapplication‐specificbrakepad
installationinstructionsprovidedbythevehiclemanufacturer.
BrakePadInstallationProcedure
Installbrakepadsproperly.Besurepadsaresecurelypositionedinthecaliper.
CheckBrakeFluid.Flushandreplace,asneeded.
Checkallhydraulicpartsforexcesswearandtear.
Checkrotorfordeepgroovesorscoring.Resurfaceorreplacerotor,asneeded.
Ifrotorsdonotneedresurfacing,thencontaminationfromthepreviousbrakepadsmustbe
removed.Sandrotorswith130‐gritsandpaperusingmoderatepressure.Usesoapandwaterto
cleanrotorsurfaceaftersanding.Rotorsshouldbefreeandclearofoil,greaseandbrakefluid.
Inspectcalipersforfreedomofmovement.Lubricatewherenecessary.
MotorcycleMetallicBed‐InInstructions
Warning–Newbrakepadscantakeupto200milestocompletelybed‐in,soavoidextremebraking
untilthepadandrotorachievesufficientsurfacecontact.
1. Afterinstallingnewbrakepads,make10stopsfrom30mphto15mph.
2. Makeanadditional10stopsfrom50mphto15mph,withaslittletimebetweenstopsas
possible.
MotorcycleOrganicBed‐InInstructions
Warning–Newbrakepadscantakeupto200milestocompletelybed‐in,soavoidextremebraking
untilthepadandrotorachievesufficientsurfacecontact.
1. Nospecialbed‐inrequired,butstillavoidextremebrakingforfirst200miles.
/