Humandata ACM-202-80C8 User manual

Brand
Humandata
Model
ACM-202-80C8
Type
User manual

This manual is also suitable for

HuMANDATA LTD.
Cyclone III FPGA Board
ACM-202 Series
User’s Manual
Ver. 3.0
Table of Contents
Revision History .............................................................................................. 1
Introduction .................................................................................................... 1
1. Unused Pins [IMPORTANT] .............................................................................. 2
2. Specifications ..................................................................................................... 3
3. Overview ............................................................................................................ 4
3.1. Name of Parts .......................................................................................................4
3.2. Block Diagram ......................................................................................................5
3.3. Power Supply ........................................................................................................6
3.4. JTAG Connector ...................................................................................................6
4. Configuration Switch ......................................................................................... 7
5. FPGA Configuration ........................................................................................... 8
6. Configuration Device Programming ................................................................... 8
7. Additional Documentation and User Support ..................................................... 9
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use
in applications that require special quality or reliability and are expected to protect human lives or
prevent accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and
nuclear power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
4. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
5. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
6. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
7. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
8. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
9. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
10. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
11. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
12. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
13. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
ACM-202 Series v3.0 1
Revision History
Date
Revision
Description
Oct. 9, 2020 v3.0
Revised: Product Revision to Rev3
Change: Configuration device
Introduction
Thank you for purchasing our product.
ACM-202 is an evaluation board equipped with an Intel (Altera) Cyclone III, power,
reset, and clock circuit and configuration device.
It can provide you with very convenient and easy-to-use environment.
ACM-202 Series v3.0 2
1. Unused Pins [IMPORTANT]
Some I/O pins in this board are fixed to GND or VCCINT (1.2 V) for purpose
adjusting the differences between devices. Some VREFB pins are connected to each
other.
Therefore, these pins should not be used as user I/O port.
For more details, please refer to the circuit schematics.
GND
VCCINT
VCCIO
NET LABEL
Pin
NET LABEL
Pin
NET LABEL
Pin
GND
V20
VCCINT
K13
VCCIO1
K8
GND
W9
VCCINT
K15
VCCIO2
W7
VCCINT
L20
VCCIO3
AB10
VCCINT
M9
VCCIO4
Y16
VCCINT
T9
VCCIO5
U21
VCCINT
U20
VCCIO6
L21
VCCINT
V9
VCCIO7
J15
VCCINT
W10
VCCIO8
J13
VCCINT
W16
VCCINT
W20
To configure the unused I/O pins using Quartus II follow the steps below:
1. Open “Assignments” and click “Device…”
2. Click “Device & Pin Options…” button
3. Set Reserve all unused pins as “As input tri-stated”
ACM-202 Series v3.0 3
2. Specifications
Model Name
ACM-202-55C8 ACM-202-80C8 ACM-202-120C8
FPGA
EP3C55F780C8N
EP3C80F780C8N
EP3C120F780C8N
Configuration Device
EPCQ64ASI16N (Intel, 64Mbit)
User I/Os
296
On-Board Clock
30 [MHz], 50 [MHz] (External inputs are available)
User Switches
6 (Push x 2, Slide x 4)
User LEDs
2
Status LEDs
2 (POWER, DONE)
Power-On Reset
200 [ms] typ. (Configuration Reset Signal)
JTAG Connector
DIL10 pin socket, 2.54 [mm] pitch
Power Input
DC 3.3 [V]
(Internal power is generated by an on-board regulator.)
PCB
8 Layer FR-4 t1.6 [mm] Immersion gold
Dimensions
3.386" x 2.126" (86 x 54 [mm])
Weight
33 [g] typ.
User I/O Connectors
FX10A-80P/8-SV1 (Hirose)
Accessories
DIL10 long pin header (Mounted)
FX10A-80S/8-SV (Hirose) x 2
FX10A-100S/10-SV (Hirose) x 2
RoHS Compliance
YES
* There may be cases that these parts and specifications are changed.
ACM-202 Series v3.0 4
3. Overview
3.1. Name of Parts
Component Side
Solder Side
Config. Device
FPGA
User I/Os (CNC)
Power & POR
User Switch
Config. Switch
JTAG
Power LED
DONE LED
User I/Os (CND)
User I/Os (CNA)
User I/Os (CNB)
Oscillator
30 MHz
50 MHz
ACM-202 Series v3.0 5
3.2. Block Diagram
Cyclone-III
EP3C55/80/120
F780C8N
Power Circuit
2.5 V
1.2 V
Power LED
(3.3 V)
DONE LED
Config. Device
User I/Os CNA
User I/Os CNB
nCONFIG
Power-On Reset
Typ. 200ms
Config. Switch
JTAG
JTAG
Buffer
.JIC
Oscillator
30 MHz
50 MHz
User LED
User Switch
64
User I/Os CNC
User I/Os CND
84
148
3.3 V INPUT
External CLK
3.3 V INPUT
External CLK
3.3 V INPUT
External CLK
3.3 V INPUT
External CLK
64
84
148
2
ACM-202 Rev.C
ACM-202 Series v3.0 6
3.3. Power Supply
This board operates from single DC 3.3 V power supply.
The external power supply should be sufficient and stabilized.
Please apply power to CNA and CNB with thick print
pattern or cable. Please connect all ground pins.
3.4. JTAG Connector
This connector is used to configure the FPGA and program the configuration device
in-system. Pin assignment is as follows.
CN3
Net Label
Signal Name
JTAG Pin
Signal Name
Net Label
XTCK
TCK
1
2
GND
GND
XTDO TDO 3 4 VCC V33A
XTMS
TMS
5
6
-
-
-
-
7
8
-
-
XTDI
TDI
9
10
GND
GND
Please use attached long pin header when you connect with download cable to the
JTAG connector.
Please pay attention not to attach cables in reverse.
Notes
Notice
ACM-202 Series v3.0 7
4. Configuration Switch
SW1 is used to set FPGA’s MSEL0, MSEL1, MSEL2 and MSEL3. “ON” means
“Low (Ground)”.
SW1
Position No.
1
2
3
4
5
6
7
8
Net Label
MSEL0
MSEL1
MSEL2
MSEL3
DSW4
DSW5
DSW6
DSW7
Default
OFF OFF OFF OFF OFF OFF OFF OFF
Function
Configuration Mode
User Switch
MSEL0
MSEL1
MSEL2
MSEL3
PS mode
0
0
0
0
AS mode
0
1
0
0
JTAG
X
X
X
X
X: Don’t care
AS mode (Configuration device access): SW1 (1, 3, 4: ON, 2: OFF)
MSEL0 = 0
MSEL1 = 1
MSEL2 = 0
MSEL3 = 0
JTAG mode: SW1 (Any setting)
MSEL0 = Any
MSEL1 = Any
MSEL2 = Any
MSEL3 = Any
ACM-202 Series v3.0 8
5. FPGA Configuration
To configure the FPGA via JTAG, please refer to the following steps.
1. Open [Tools] menu, then click [Programmer].
2. Select [JTAG] from [Mode] list.
3. Open [Processing] menu, then click [Auto Detect].
4. Double-click [none] and select the sof file you made.
5. Check [Program/Configure] and [Verify].
6. Open [Processing] menu, then click [Start].
If configuration is completed successfully, the DONE LED will light up.
Advice
Check if FPGA device name you set is same as that on the board.
Please check unused pins setting. (See section.1)
Quartus II help will give you more information.
6. Configuration Device Programming
To program the configuration device via JTAG , you need to prepare jic (JTAG
Indirect Configuration) file. You can generate jic file from sof file using Quartus II.
Please refer to the following steps.
Generating jic file
1. Open [File] menu, then click [Convert Programming Files].
2. Select [JTAG Indirect Configuration File] from [Programming file type] list.
3. Select the device name which on the board from [Configuration device] list.
4. Fill the [File name] as you like.
5. Click [Add Device], then select [Device family] and [Device name].
6. Click [Add File…], then select the sof file for input file.
7. Click [Generate].
Programming Configuration Device
8. Open [Tools] menu, then click [Programmer].
9. Select [JTAG] from [Mode] list.
10. Open [Processing] menu, then click [Auto Detect].
11. Select the jic file you made.
12. Check [Program/Configure] and [Verify]
13. Open [Processing] menu, then click [Start].
ACM-202 Series v3.0 9
After programming is completed successfully, turn off and on the power.
Configuration data in the configuration device will be automatically loaded into the
FPGA.
Advice
Check if the configuration device name, FPGA device family name and
device name you selected in step 3 and 5 are same as those on the board.
Quartus II help will give you more information.
7. Additional Documentation and User Support
The following documents and other supports are available at
https://www.hdl.co.jp/en/spc/ACM/acm-202/
Circuit Schematic
Pin List
Dimensional drawing
PCB drawing
Net List
… and more.
Cyclone III FPGA Board
ACM-202 Series Rev3
User’s Manual
Ver. 3.0 .............................................. Oct. 9, 2020
HuMANDATA LTD.
Address: 1-2-10-2 F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: https://www2.hdl.co.jp/en/ (Global)
https://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Humandata ACM-202-80C8 User manual

Brand
Humandata
Model
ACM-202-80C8
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers