INSTALLATION INSTRUCTIONS
NORTH AMERICA
1321 S. State College Blvd.
Fullerton, CA 92831 USA
USA and Canada
Phone: 1.800.368.9700
Fax: 1.800.832.4888
Other Locations
Phone: (001).714.632.7100
Fax: (001).714.632.1044
P4263T-EX
Exterior Tilting Low-Prole Mount for Flat-Panels
P4263T-EX
Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Contact Premier Mounts with any questions:
(800) 368-9700
Contents
Warning Statements
Weight Limit
Maximum Flat Panel Weight: 175 lbs.
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT
LEAST FOUR TIMES THE WEIGHT OF THE FLAT PANEL. IF NOT,
THE WALL STRUCTURE MUST BE REINFORCED.
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND
COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED, AS OUTLINED
IN THESE INSTALLATION INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE, SERIOUS
PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE
PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS,
DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR
IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
At least two qualied people should perform the assembly procedure. Personal injury and/or property damage can result
from dropping or mishandling the at panel.
If mounting to wall studs or ceiling studs, make sure that the mounting screws are anchored into the center of the wall studs
or ceiling studs. Use of an edge-to-edge stud nder is recommended.
It is recommended that a maximum of ⅝″ plaster board be used when mounting to wooden studs.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there
are no electrical wires in wall. Cutting or drilling into an electrical line may cause serious personal injury.
Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a
water or gas line may cause severe property damage or personal injury.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious
personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of
impact.
Weight Limit. ................................................................................................................................................................................. 2
Warning Statements. .................................................................................................................................................................... 2
Installation Tools. .......................................................................................................................................................................... 3
Parts List....................................................................................................................................................................................... 3
Mounting Hardware. ..................................................................................................................................................................... 4
Installing the Wall Plate. ............................................................................................................................................................... 5
Introduction. ................................................................................................................................................................... 5
Determining the Mounting Surface................................................................................................................................. 5
Wood Stud Installation. .................................................................................................................................................. 5
Concrete Installation. ..................................................................................................................................................... 7
Installing the Mounting Bracket. ................................................................................................................................................... 8
Selecting the Mounting Hardware. ................................................................................................................................. 8
Universal Washer Installation. ........................................................................................................................................ 9
Universal Spacer Installation.......................................................................................................................................... 9
Attaching the Mounting Bracket to the Flat Panel. ....................................................................................................... 10
Lock-It™ Security Barrel Installation (Optional).......................................................................................................................... 10
Attaching the Flat Panel to the Wall Plate. ....................................................................................................................11
Mounting Bracket Adjustments. ...................................................................................................................................................11
Leveling Screw Adjustment. ..........................................................................................................................................11
Locking Screw Adjustment. ...........................................................................................................................................11
Tilt Adjustment. ............................................................................................................................................................. 12
Utilizing the Security Barrel. ......................................................................................................................................... 12
Technical Specications. ............................................................................................................................................................ 13
Warranty. .................................................................................................................................................................................... 14
P4263T-EX
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3
Parts List
Installation Tools
e following tools may be required depending upon your particular installation. ey are not included.
Make sure your Premier Mounts product has the following hardware and components before beginning installa-
tion. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.
P4263T-EX Universal Low Prole Tilt Mount Assembly Components
Wall Plate
(Qty 1)
Mounting Brackets
(Qty 2)
5/16” x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
(Qty 8)
5/16” Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 4)
Security Barrel
(Qty 1)
Pencil Level
1/4” Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8” concrete Drill Bit**
Protective Eyewear
* Optional tools for steel stud installations.
** Optional tools for concrete installations.
½˝ Socket
O
N
M6 x 30mm Screw
(Qty 2)
M6 x 35mm Screw
(Qty 2)
Twist-Action Finned Anchor (Qty 6)
P4263T-EX
Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
av Mounting Hardware
Parts List (cont’d)
M4 x 12mm Screw
(Qty 4)
M4 x 16mm Screw
(Qty 4)
M4 x 25mm Screw
(Qty 4)
M5 x 12mm Screw
(Qty 4)
M5 x 16mm Screw
(Qty 4)
M5 x 25mm Screw
(Qty 4)
M6 x 12mm Screw
(Qty 4)
M6 x 16mm Screw
(Qty 4)
M6 x 25mm Screw
(Qty 4)
M8 x 16mm Screw
(Qty 4)
M8 x 12mm Screw
(Qty 4)
M8 x 25mm Screw
(Qty 4)
P4263T-EX
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 5
Installing the Wall Plate
V
Introduction
Directional Mounting Arrow
The Directional Mounting Arrow stamped into the top of the P4263T-EX
wall mount indicates which edge is the top.
Mounting Safety
Two people are recommended to install this mount.
If you will be installing your P4263T-EX mount to wood studs,
proceed to the “Wood Stud Installation” section.
If you will be installing your P4263T-EX mount to a concrete wall,
proceed to the “Concrete Installation” section.
If you will be installing your P4263T-EX mount to a steel frame, proceed to the
“Steel Stud Installation” section.
Determining the Mounting Surface
C
onc
rete
St
ee
l
St
u
d
Wo
o
d
St
u
d
5/16”X3” LAG BOLTS ANCHORS & 5/16”X3
LAG BOLTS
USE COMMERCIAL AVAILABLE
SUITABLE HARDWARE
Step 2
Two people are recommended for this step; one person to level the wall
plate and another person to mark the wall stud location.
Place the wall plate against the wall in the desired viewing location.
Adjust the wall plate to align the mount slots in the wall plate with the
center of the wall studs.
Level the wall plate.
Use a pencil to mark the upper right mounting location along the center of
the wall stud.
Wood Stud Installation
You must secure the wall plate to two (2) wall studs with a minimum of
four (4) lag bolts (2 lag bolts for each stud found).
Use a stud nder to determine the exact center of wall studs in the vicinity
of the wall plate.
Use a pencil to mark the exact center of each of the wall studs.
Step 1
XX
P4263T-EX
Page 6 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Installing the Wall Plate (cont’d)
Place the wall plate against the wall and align it with the pilot hole.
Insert one (1) 5/16” x 3″ lag bolt and one (1) 5/16” washer into the upper
right mounting hole and tighten using a socket wrench and 1/2” socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Drill a “pilot hole” in the center of the upper right mark using a 1/4” drill bit and
power drill.
Only use a 1/4” drill bit when drilling the pilot holes.
Level the wall plate.
Use a pencil to mark the remaining three (3) mounting locations along the
center of each wall stud.
Step 6
Two people are recommended for this step; one person to level the wall
plate and another person to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with a power drill and a ¼″
drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
P4263T-EX
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7
Installing the Wall Plate (cont’d)
The supplied Finned anchors must be used for concrete installation.
You will need a 3/8” concrete drill bit (commercially available)
Concrete Installation
Example of 3/8” Concrete Drill Bit (Not Included)
Finned Anchor
Step 7
Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″ washer into each pilot hole.
Tighten all lag bolts using a socket wrench and ½″ socket.
Do not overtighten the lag bolts when attaching the mount to the wall. Improper
installation may result in personal injury or property damage.
Proceed to the “Installing the Mounting Bracket” section.
Two people are recommended for this step; one person to level the wall
plate and another person to mark the mounting locations.
Place the wall plate against the wall in the desired viewing location.
Level the wall plate.
Use a pencil and mark 2 upper and 2 lower mounting locations where
you will be drilling holes for the Finned anchors. Each horizontal location
cannot be closer than 12″ apart.
Set the wall plate to one side in a safe location.
Step 1
Use a power drill and 3/8″ concrete drill bit to drill a hole at each of the marks.
Step 2
12”
P4263T-EX
Page 8 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Installing the Wall Plate (cont’d)
Selecting the Mounting Hardware
Insert a small straw or toothpick into the threaded inserts found on the
back of the at panel.
Use a pencil to mark the depth of the threaded insert on the small straw or
toothpick.
Mark the straw or toothpick 1/8” above the depth of the threaded insert, as
shown in Figure 1.
Insert the small straw or toothpick into the remaining threaded inserts
to compare and verify their depth using the straw or toothpick’s 1/8”
allowance mark.
Locate the correct diameter screw for the threaded insert.
If the screw you selected is longer than the 1/8” allowance mark on the
small straw or toothpick, as shown in Figure 2 and Figure 3, do not use
this screw. The screw length must not bypass the mark.
Test each size of the screws provided.
The correct screws should thread easily into the mounting point and not
pull out when tension is applied.
Proceed to the “Universal Washer Installation” section.
Installing the Mounting Bracket
Small Straw or Toothpick
Small Straw
or Toothpick
Small Straw
or Toothpick
Marking the 1/8”
Allowance
Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Step 4
Insert a Finned anchor into each hole.
If necessary, lightly tap each Finned anchor into place with a hammer.
Step 3
Place the wall plate against the wall over the Finned
anchors, then secure the 5/16” x 3 lag bolts to the
anchors.
Do not over tighten
P4263T-EX
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 9
Universal Washer Installation
Flat Panel
Universal Washer
Universal Spacer
Mounting Bracket
Mount Point
Mounting Screw
Premier Mounts’ Universal Washers are designed to accommodate the various
M4, M5, M6 and M8 hole sizes required by at panels.
Do not place excessive pressure on the back of the at panel, as this
may damage your at panel.
The Universal Washer must be installed between the head of the
mounting screw and the mounting bracket as shown.
Does your at panel have:
●Recessed mount points?
●Uneven mount points?
●A curved back?
●Any obstruction near the mount point?
If Yes, you must install Universal Spacers. Remove the mounting brackets,
Universal Washers, and mounting screws from the back of the at panel.
Proceed to the “Universal Spacer Installation” section.
If No, skip to the “Attaching the Mounting Bracket to the Flat Panel”
section.
Universal Spacer Installation
Premier Mounts’ Universal Spacers allow you to attach the mounting bracket
to at panels which have recessed or uneven mount points. Each Universal
Spacer adds ¼˝ to the distance between the mounting bracket and your at
panel.
The Universal Spacers must be stacked and oriented as shown.
The Universal Spacers must only be installed between the mounting
bracket and your at panel.
The Universal Spacers will t M4, M5, M6 and M8 screw sizes.
Proceed to the “Attaching the Mounting Bracket to the Flat Panel” section.
M8
M5, M6
M4
1˝ ¼˝
Installing the Mounting Bracket (cont’d)
P4263T-EX
Page 10 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Installing the Mounting Bracket (cont’d)
This section presumes that you have read and understood these sections:
●Selecting the Proper Mounting Hardware
●Universal Washer Installation
●Universal Spacer Installation
Place your at panel screen-side down on a soft, at surface.
Identify the number and location of the thread inserts on the back of your
at panel.
Align the holes on each mounting bracket with the thread inserts on the
back of your at panel.
Secure each mounting bracket to your at panel by inserting a minimum of
two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Attaching the Flat Panel to the Wall Plate” section.
Attaching the Mounting Bracket to the Flat Panel
Lock-It™ Security Barrel Installation (Optional)
Do not overtighten the locking screw.
Please read the following directions to install the security barrel:
Remove the locking screw from the mounting bracket.
Place the locking screw into and through the security barrel (see
illustration below).
Re-insert the locking screw and security barrel into the mounting bracket.
Tighten the locking screw and security barrel until seated in the mounting
tab.
Optional security congurations include:
- Padlock (Combination or Keyed; commercially
available)
Lock-It™ Security
Barrel
Locking Screw
Do not thread the locking screw any further once it is even with the
mounting tab (see illustration to the right). Threading the locking screw
any further will prevent you from safely attaching the at panel to the
wall plate.
Proceed to the “Attaching the Mounting Bracket to the Flat Panel”
section.
Mounting Tab
P4263T-EX
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 11
Leveling Screw Adjustment
If your at panel is tilted too far to one side, the leveling screws will allow you to
compensate for this tilt by simply adjusting the screws with a screwdriver.
Loosen both locking screws.
Adjust the tilt of your at panel.
Tighten both locking screws.
Caution!
It is possible to dislodge your at panel while you level your at panel.
Use extreme caution until you tighten the locking screws.
Mounting Bracket Adjustments
Locking Screw Adjustment
After you have nished leveling your at panel, be sure to tighten the two (2) M6
x 35mm locking screws.
Do not overtighten the locking screws.
M6 x 35mm
Locking Screw
(1 per Bracket)
M6 x 30mm
Leveling Screw
(1 per Bracket)
This section requires two people.
Do not release your at panel until you are certain that top and bottom
hooks of both mounting brackets are securely seated on the upper and
lower mounting rails of the wall panel.
Raise the at panel past the top and bottom mounting rails on the wall
panel.
Slide the at panel down slowly, keeping it close to the wall.
Engage the top and bottom mounting brackets to the rails of the wall plate.
Proceed to the “Mounting Bracket Adjustments” section.
Attaching the Flat Panel to the Wall Plate
P4263T-EX
Page 12 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Tilt Adjustment
Adjusting the Flat Panel Friction Tilt Angle
Place one hand at the center top edge of the at panel.
Place the other hand on the center bottom edge of the at panel.
Using the upper hand, gently pull the top of the at panel towards you
while the lower hand gently pushes the bottom of the at panel away from
you.
Adjusting the Flat Panel to the Original Position
Place one hand at the center top edge of the at panel.
Place the other hand on the center bottom edge of the at panel.
Using the upper hand, gently push the top of the at panel towards the wall
while the lower hand gently pulls the bottom of the at panel away from the
wall.
v
Padlock
(Combination or Keyed)
Utilizing the Security Barrel
Your P4263T-EX Mount includes one (1) Security Barrel which can provide
additional theft deterrence for your at panel.
Padlock -
Place the locking hook through the hole of the
security barrel.
Snap lock and locking hook together.
P4263T-EX
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 13
Technical Specications
All measurements are in inches [millimeters].
Limited Warranty. Thank you for buying our Class B Mount designated
for outdoor use in dry or humid locations but specically excluding coastal
locations. Progressive Marketing Products, Inc. (d/b/a Premier Mounts)
("Premier Mounts") warrants to the buyer ("Buyer") at the original installa-
tion site ("Site") that any of the Class B Mounts components designed and
manufactured by Premier Mounts and installed at the Site ("Product") shall
be free from defects in material and workmanship which substantially impair
their ability to perform their intended function, as reference in the Class
B Mounts Product Information, for a period of ve (5) years - except that
any factory-applied powder coat painted nish is warranted to be free from
substantial manufacturing-related visible peeling or cracking or chalking un-
der normal atmospheric conditions for a period of one (1) year ("Finished
Warranty") - from the earlier of 1) the date the installation of the Product
at the Site is substantially complete, or 2) 120 days after the purchase of
the Product by the original Buyer of the Product ("Warranty Period"). This
Limited Warranty may not be assigned or transferred by the Buyer.
FINISHED WARRANTY LIMITATIONS
The Finish Warranty does not apply to any issues caused by for-
eign residue deposited on the nish, or an installation in at-
mospheric conditions more corrosive than normal conditions.
WARRANTY LIMITATIONS
The Limited Warranty covers only the Products and not any other
materials not provided by Premier Mounts. Goods which may be sold
by Premier Mounts, but which are not designed or manufactured by Pre-
mier Mounts are not warranted by Premier Mounts, are sold only with
the warranties, if any, of the original manufacturers thereof. This Limited
Warranty does not cover damage to the Product that occurs during its
shipment, storage, installation or use, or from force majeure acts includ-
ing re, ood, earthquake, storm, hurricane or other natural disaster, war,
terrorist activities, act of foreign enemies and criminal acts. This Limited
Warranty does not cover damages or problems caused the connections
to or use of alternative materials not purchased from Premier Mounts.
This Limited Warranty shall be void if (A) any Product that was pur-
chased from anyone other than Premier Mounts or one of its authorized
reseller, (B) installation of the Product is not performed in accordance
with the Premier Mounts Product Information, (C) if the Product has been
modied, repaired, or reworked in a manner not previously authorized
by Premier Mounts in writing, (D) the Product is installed in an environ-
ment for which it was not designed, (E) damage to the surface or exte-
rior of a Product that has been deface, scratched or has been exposed
to foreign chemicals, liquids, gases or other out of the ordinary corrosive
materials or conditions, (F) structural damage caused by settling or move-
ment of land or objected to which a Product was attached, (G) any claim
relating to failure, loss or damage caused by neglect, misuse or abuse;
improper operation or storage; modication or alteration; failure to follow
proper operating procedures; or failure to maintain the Product according
to in accordance with reasonable and customary maintenance procedures.
ORIGINAL WARRANTY CLAIMS
If, within the Warranty Period, the Product shall be proven at Premier Mounts
sole discretion to be nonconforming, then Premier Mounts shall repair or
provide a replacement for the nonconforming Product, or any nonconform-
ing part thereof, at Premier Mounts option. Any such repair or replacement
does not cause the beginning of new warranty terms, not shall the Warranty
Period of this Limited Warranty be extended. Premier Mounts aggregate li-
ability for all warranty claims shall not exceed the original Purchase price of
the nonconforming Product. Buyer's right to the benets of this warranty are
conditioned on Buyer's cooperation with Manufacturer's reasonable requests
which it deems necessary to verify that the claimed defect is covered by this
Limited Warranty. A repair shall be deemed acceptable if the defect does not
affect a Product's performance and the defect is not plainly visible from a
distance of seven feet. Buyer shall bear all costs of shipment or transporta-
tion related to the repair or replacement of the nonconforming product. Such
repair or replacement shall be Buyer's sole remedy and shall fulll all of Pre-
mier Mounts obligations with respect to the Product and all warranty claims.
What You Must Do To File a Claim. To le a claim under the Warranty,
you must call Premier Mounts Customer Care line at 1-877-668-6830 within
(30) days after Owner has actual or constructive notice of a product which
is allegedly defective. Premier Mounts will issue an RMA Case Number, and
the claim along with defective product shall be sent to: Premier Mounts,
1321 South State College Blvd., Fullerton, CA 92831, Attention RMA#. All
Claims shall provide details explaining the nature of the claim and the date
of detection. Owner waives any claims not made in this manner during
the Warranty Period. Premier Mounts shall have a full and complete op-
portunity to inspect any alleged defect. *For coastal areas related claims,
please contact Premier Mounts for warranty information. Within a reason-
able time after proper notication, Premier Mounts will evaluate your claim
and resolve it in accordance with the terms of this Warranty. You should
retain this certicate for your records in the event you need to le a claim.
Sole and Exclusive Warranty. THIS WARRANTY IS EXCLUSIVE AND
REPLACES ALL OTHER WARRANTIES, WHETHER EXPRESS OR
IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. This written
warranty is your exclusive warranty from Premier Mounts and represents
the SOLE REMEDY available to any owner of Premier Mounts Class B
Mount. Premier Mounts makes NO OTHER REPRESENTATION OR WAR-
RANTY of any kind other than that stated herein. PREMIER MOUNTS
WILL NOT BE LIABLE IN ANY EVENT FOR CONSEQUENTAL, INDI-
RECT OR INCIDENTAL DAMAGES OF ANY KIND, whether for breach
of this warranty, negligence, strict liability in tort, or for any other cause.
Some states do not allow the exclusion or limitation of incidental or conse-
quential damages so the above exclusions or limitations may not apply to you
Modication of Warranty. This Limited Warranty may not be changed or
modied. No one, including any representative or employee of Premier
Mounts or any authorized reseller, has authority to assume any additional li-
ability or responsibility for Premier Mounts. This Warranty gives you specic
legal rights, and you may have other rights which vary from state to state.
2335889.4
17786-200 Class B Mounts
9531-000-004-0X Rev.1
Limited Warrenty - Class B
P4263T-EX
Page 14
/