Ranger design N5-RA12-4 Installation guide

Brand
Ranger design
Model
N5-RA12-4
Category
Wall & ceiling mounts accessories
Type
Installation guide
INSTALLATION GUIDE
N5-RA12-4 Shelving ( ALUMINUM )
Transit High Roof & Medium Roof
Promaster Standard Roof & High Roof
Nissan NV High Roof
Box Truck / Trailer
Sprinter RWB, LWB, XWB
QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
q 1.1 Setup...............................................................................................................................................
q 1.2 Shelf Assembly................................................................................................................................
3 - 4
5
Phase 1 - Assembly
Phase 2 - Installation
6
7
8 - 9
10 - 11
12 - 13
q 2.1 Attach Wall Brackets To The End Panels........................................................................................
q 2.2 Mark Holes For Plus Nuts...............................................................................................................
q 2.3 Attach Plus Nut...............................................................................................................................
q 2.4 Attach Shelf Unit To the Floor.........................................................................................................
q 2.5 Attach Wall Brackets......................................................................................................................
q Cordless Impact
q Cordless Drill
q Tape Measure
q Marker
q 1/2" Socket
q 1/2" Drill Bit w/ Drill Collar ( Set at 1/2" )
q 3/8" Driver Bit
q Knife
q Plusnut Tool / Plusnut Gun ( 5/16" )
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
Item No. Description Qty.
40-750 Bracket, N5 Series, Right 1
40-751 Bracket, N5 Series, Left 1
84-012 foldaway bracket - middle 2
40 - 705 End Panel ( Left ) 1
40 - 706 End Panel ( Right ) 1
60 - 11.875 × 12 Shelf Tray, Black Plywood, Usable 12" × 12" 1
60 - 13.875 × 12 Shelf Tray, Black Plywood, Usable 14" × 12" 3
94 - 4025 Assembly Fastener Kit 1
96 - 4025 Install Fastener Kit 1
BILL OF MATERIALS
60 - 11.875 × 12
60 - 13.875 × 12
40 - 705 40 - 706
40 - 750
84-012
40 - 751
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 4
94 - 4025 Fastener Kit Fastener Assembly
96 - 4025 Fastener Kit Fastener Assembly
1.1.3 Fastener kits.
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
8×8×
32×32×
#92-102 Screw #14 × 1"
8×8×
Hex Bolt
5/16"-18 × 3/4"
GR-5 ZINC
# 90-204
# 94-116
Serrated Nut
5/16"-18
ZINC
8×8×
# 92-102
Screw HWH
#14 × 1"
ZINC
32×32×
8×8× # 98-116
Flat Washer
5/16" - 18 × 1"
ZINC
8×8×
Hex Bolt
5/16"-18 × 1-1/4"
GR-5 ZINC
# 90-212
4×4×
Hex Bolt
5/16"-18 × 1-3/4"
GR-5 ZINC
# 90-011
12×12× Plusnut
# 94-132
12×12× # 98-122
Lock Washer
5/16"
ZINC
4×4×
Spacer
0.375" ID, × 1.0" OD × 0.25" LONG
NYLON
# 98-157
12×12× # 98-116
Flat Washer
5/16", O.D. 7/8"
ZINC
8×8×
#90-212 Hex Bolt 5/16" × 1-1/4"
#98-122 Lock Washer
#98-116 Flat Washer
#94-132 5/16" Plusnut
#94-132 5/16" Plusnut
4×4×
#90-011 Hex Bolt 5/16" × 1-3/4"
#98-122 Lock Washer
#98-116 Flat Washer
#98-157 Spacers
( QTY = Gap beTween floor and end panel )
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 5
#92-102 Screw #14 × 1"
HARDWARE USED
32×
TOOLS
q Cordless Impact
q 3/8" Driver Bit
1.2.1 Attach both panels to the shelf trays.
PHASE 1 – ASSEMBLY
1.2 SHELF ASSEMBLY
15"
ADJUSTABLE
15"
ADJUSTABLE
15"
ADJUSTABLE
5 - 11/16"
ADJUSTABLE
12" × 12"
14" × 12"
40 - 706
40 - 705
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 6
PHASE 2 – INSTALLATION
2.1 ATTACH WALL BRACKETS TO THE END PANELS
2.1.1 • Lift the assembled shelf to the vehicle, then put it in place.
• Attach the brackets to the panels aligning the brackets to the horizontal rim of the vehicle.
84-012
40-750
IMPORTANT: For all Box Trucks, make sure that the shelving is securely fastened to the structure of the truck.
HORIZONTAL RIM
Attach the brackets to the panels aligning the
brackets to the horizontal rim of the vehicle.
TOOLS
q Cordless Impact
q 1/2" Socket
HARDWARE USED
8× hANd-tIghteN the boLts
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
40-751
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 7
2.2.1 After attaching the brackets mark the holes on the brackets and end panels to the vehicle.
PHASE 2 – INSTALLATION
2.2 MARK HOLES FOR PLUS NUTS
TOOLS
q Marker
MARK
Mark 4 holes of the brackets
on the vehicle as shown on the
image.
NOTE: If you are using Ranger wall
kits, please go to pAge 13.
TOOLS
q Marker
MARK
Mark 2 holes of each end panel on the
vehicle oor.
NOTE: If you are using Ranger oor,
please go to pAge 11.
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 8
PLUSNUT
PHASE 2 – INSTALLATION
2.3 ATTACH PLUS NUTS
WARNING: Before drilling, ensure that you will not hit any critical parts of the vehicle like the Gas tank,
Wiring Harness and Hose.
NOTE: Use 1/2" drill bit with drill collar to stop drill at 1/2" depth.
2.3.1 • Lift the assembled shelf on the side.
• Drill all the marks using 1/2" drill bit w/ drill collar, then attach plus nuts to the holes.
Drill all the marks then, attach plus nuts to the
holes.
HARDWARE USED
12×
#94-132 Plus Nut
DRILL COLLAR
( seT aT 1/2" )
TOOLS
q Cordless Drill
q 1/2" Drill Bit w/ Drill Collar ( Set at 1/2" )
q Plus Nut Tool ( 5/16" )
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 9
FORWARD REVERSE
STEP: Put the plusnut on the plusnut gun, then attach the plus nut in the hole by turning the gun forward until
the plus nut locks, then remove the gun by turning in reverse.
• UsINg pLUsNUt gUN
• UsINg the 6491 pLUsNUt tooL
2.3.2 How to attach plus nut.
6491 HARDWARE USED
Flat washer 5/16"
Flat washer 5/16" BS × 7/8" OD
TOOLS
q Cordless Impact
q 1/2" Socket
q 9/16" Wrench
STEP 1:
Assemble the 6491 plusnut tool with the hardware needed, plus
nut and the 9/16" wrench as shown.
FORWARD REVERSE
STEP 2:
Attach the plus nut in the hole by turning
the bolt forward using an impact with a
1/2" socket until the plusnut locks, then
remove the bolt by turning the impact in
reverse.
NOTE: The hardware used for the 6490 plusnut tool is not included in the fastener bag.
The 6490 plusnut tool can be ordered separately upon demand at no charge.
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 10
2.4.1 Put the assembled shelf back in place aligning the holes to the plusnuts, then install the
end panels to the plus nuts.
PHASE 2 – INSTALLATION
2.4 ATTACH SHELF UNIT TO THE FLOOR
wIthoUt rANger fLoor
TOOLS
q Cordless Impact
q 1/2" Socket
#90-011 Hex Bolt 5/16" × 1-3/4"
#98-122 Lock Washer
#98-116 Flat Washer
#98-157 Spacers
( QTY = Gap beTween floor and end panel )
HARDWARE USED
6×
#94-132 5/16" Plusnut
W/ Spacer W/O Spacer
Most vehIcLe Use 1 spAcer wheN Not over rIbs
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 11
2.4.2 • Lift the shelving unit inside the van, then put it in place.
• Install the shelving unit to the floor mounting track by sliding bolts in the mounting tracks,
and putting screw in the last rear slot of the end panels of the shelving unit.
wIth rANger fLoor
#94-104 Hex Nut
#98-116 Lock Washer
#98-122 Flat Washer
#90-490 Carriage Bolt 5/16" × 1"
HARDWARE USED
2× fLoor fAsteNer kIt
#92-102 Screw 1"
HARDWARE USED
2× fLoor fAsteNer kIt
TOOLS
q Cordless Impact q 3/8" Driver Bit
q 1/2" Socket
7/16 drill hole
HARDWARE USED
4× hANd-tIghteN the boLts
TOOLS
q Marker
q 7/16" Drill Bit
q 1/2" Socket
E-FLOOR
STANDARD FLOOR
HARDWARE USED
4× hANd-tIghteN the boLts
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#98-116 Lock Washer
#99-114 Zinc Alloy Tapping Inserts
for Softwood
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 12
2.5.1 Aligned the wall brackets to the plus nuts, then install the wall brackets to the wall.
IMPORTANT: After installation is completed, ensure all bolts are tightened.
TOOLS
q Cordless Impact
q 1/2" Socket
HARDWARE USED
8×
#90-212 Hex Bolt 5/16" × 1-1/4"
#98-122 Lock Washer
#98-116 Flat Washer
#94-132 5/16" Plusnut
NOTE: Tightened the bolts that used to attached the wall bracket to the wall or wall kits 1st
before the bolts that used to attached the wall bracket to the end panel.
PHASE 2 – INSTALLATION
2.5 ATTACH WALL BRACKETS
wIthoUt rANger wALL kIts
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 13
TOOLS
q Cordless Impact
q 1/2" Socket
FASTENERS USED
8× wALL kIts fAsteNer kIt
#90-208 Hex Bolt 5/16" × 1"
#98-122 Lock Washer
#98-116 Flat Washer
#94-150 Channel Nut
2.5.2 First align the wall brackets to the wall mounting track kits, then install the wall brackets
to the wall mounting track kits using channel nuts.
IMPORTANT: First tighten the bolts that secure the wall bracket to the wall or wall kits, and then tighten the
bolts that secure wall bracket to the end panels. After installation is completed, ensure all bolts are properly
tightened.
wIth rANger wALL kIts
For technical support, contact us at 1-800-565-5321 N5-RA12-4 Installation Guide | REV. C | Page 14
“You have successfully installed your
N5-RA12-4
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: cs@rangerdesign.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Ranger design N5-RA12-4 Installation guide

Brand
Ranger design
Model
N5-RA12-4
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents