2. Ambiance
  3. OUTLANDER 15
OUTLANDER 15

Ambiance OUTLANDER 15 User manual

  • Hello! I've reviewed the product details for the Ambiance Outlander 15 Fireplace. This document provides information on dimensions, specifications, and clearances. I am ready to answer your questions about the different aspects of the fireplace, from its BTU output to the required installation clearances and additional options such as blower kit.
  • What is the BTU output of the Outlander 15?
    What is the recommended log length?
    What is the required clearance to a back wall using a single wall connector?
    Is floor protection required?
Outlander®
WOOD COLLECTION
Model: Outlander® 15
Ambiance® Fireplaces & Grills www.ambiancereplaces.com
Leg Model
Top View
Front View Side View
Overall Dimensions
O 6”
(152mm)
6 1/2”
(165mm)
31 1/2”
(800mm)
13”
(330mm)
21 5/8”
(549mm)
19 3/4”
(502mm)
26”
(660mm)
25 1/4”
(641mm)
16 1/2”
(419mm)
9 1/4”
(235mm)
17”
(432mm)
O 6”
(152mm)
6 1/2”
(165mm)
31 1/2”
(
800mm)
13”
(330mm)
21 5/8”
(549mm)
19 3/4”
(502mm)
26”
(660mm)
25 1/4”
(641mm)
16 1/2”
(419mm)
9 1/4”
(235mm)
17”
(432mm)
O 6”
(152mm)
6 1/2”
(165mm)
31 1/2”
(800mm)
13”
(330mm)
21 5/8”
(549mm)
19 3/4”
(502mm)
26”
(660mm)
25 1/4”
(641mm)
16 1/2”
(419mm)
9 1/4”
(235mm)
17”
(432mm)
Outlander®
WOOD COLLECTION
Model: Outlander® 15
Ambiance® Fireplaces & Grills www.ambiancereplaces.com
Overall Dimensions
Pedestal Model
Top View
Front View Side View
26”
(660mm)
31 3/8”
(770mm)
O 6”
(152mm)
6 1/2”
(165m
m)
13”
(330mm)
19 3/4”
(502mm)
21 5/8”
(549mm)
9 1/4”
(235mm)
22 1/4”
(565mm)
18 1/8”
(460mm)
16 1/2”
(419mm)
26”
(660mm)
31 3/8”
(
770mm)
O 6”
(152mm)
6 1/2”
(165mm)
13”
(330mm)
19 3/4”
(502mm)
21 5/8”
(549mm)
9 1/4”
(235mm)
22 1/4”
(565mm)
18 1/8”
(460mm)
16 1/2”
(419mm)
26”
(660mm)
31 3/8”
(770mm)
O 6”
(152mm)
6 1/2”
(165mm)
13”
(330mm)
19 3/4”
(502mm)
21 5/8”
(549mm)
9 1/4”
(235mm)
22 1/4”
(565mm)
18 1/8”
(460mm)
16 1/2”
(419mm)
Outlander®
WOOD COLLECTION
Model: Outlander® 15
Ambiance® Fireplaces & Grills www.ambiancereplaces.com
Specications
Framing and Clearances
BACK WALL
B
SIDE W ALL
A
BACK WALL
C
SIDE WALL
F
D
E
E
PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR
Sidewall (A) 19" (48.3 cm)
Sidewall to ue (B)
28" (73.3m)
Backwall (C)
17.5" (44.5 cm) 12.5" (31.8 cm)
Backwall to ue (D)
21" (53.3 cm) 16" (40.6 cm)
Corner (E)
11" (279 mm) 7" (178 mm)
Ceiling (F)
84" (213.4 mm) 75" (190.5 cm)
Clearances can be reduced with shielding acceptable to local authorities.
Reduced installation must comply with NFPA 211 or CAN/CSA-B365.
BTU
FIREBOX
EFFICIENCIES VENTING
Cordwood EPA Cu. Ft Log Length g / hr Optimal% HHV Type Diameter
52,000 30,042 1.9 20 1.57g 75% 71.61% Class A 6-inch
GLASS DIMENSIONS BLOWER
Type Dimensions Area sq in Height Depth Width Type CFM
Ceramic 16.5” X 9.24” 152 31.5” 21.63” 26”
Optional - Heat activated, variable speed
150
Outlander®
WOOD COLLECTION
Model: Outlander® 15
Ambiance® Fireplaces & Grills www.ambiancereplaces.com
Alcove Installation
Floor protection
Your appliance may be installed using a listed double wall
connector, such as Security DL6 in Canada, the Simpson
Duravent Plus DVL in the USA or an equivalent double wall
connector, into an alcove having a depth of no more than 4
feet and a height of at least 6'3". The minimum clearance are
as shown.
If the appliance is to be installed on top of a combustible oor, it must be placed on an approved non-combustible hearth pad,
that extends 8" (203 mm) beyond the appliance sides and back and 18" (457 mm) in Canada / 16" (406 mm) in the USA to the front.
The reduced clearance from the back of the appliance may result in the appliance pad terminating shorter than 8" (203 mm)
beyond the appliance.
Refer to local building codes for suitable oor protection materials.
ALCOVE
PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR
Ceiling (G)
N/A
7" (190.5 cm)
Side wall (H)
19" (48.3 cm)
Sidewall to ue (I)
28.875" (73.3 cm)
Blackwall (J)
12.5" (31.8 cm)
Blackwall to ue (K)
16" (40.6 cm)
MINIMUM FLOOR PROTECTION
FRONT (L) SIDES (M) BACK (N)
CANADA 18" (45.7 cm) 8" (203 mm)
USA
16" (406 mm) 8" (203 mm)
note:
Floor protection is required for spark and ash shielding, but not for limiting oor temperatures from the radiant heat
of the appliance. The appliance was designed and safety-tested so that without any protection, the oor would not
overheat.
note:
If a section of horizontal chimney connector is used, oor protection is required under the
chimney connector and 2" (51 mm) beyond each side.
K
J
J
I
19"
(48.3cm)
28
7
/
8
"
(733.4mm)
ALCOVE
48” (122cm)
MAX
A B
F
Outlander®
WOOD COLLECTION
Model: Outlander® 15
Ambiance® Fireplaces & Grills www.ambiancereplaces.com
Optional Blower Kit Installation
Provisions have been made on this appliance to install an optional blower kit (EPT70) that comes complete with a variable speed
switch to turn blower ON/OFF, as well as to adjust the blower speed.
THERMAL DISC
BRACKET
SCREWS
2100 PEDESTAL
MODEL ILLUSTRATED
1. Ensure the thermal disc bracket is in
the correct postion (Fig. 1).
2. Remove the knock-out from the back
of the appliance.
3. Install the blower and housing as
shown (Fig. 2) using 4 screws (sup-
plied).
4. Loosen the adjustment screws.
5. Reach between the outer panel and
the rebox, then slide the thermal disc bracket until the thermal disc is touching the rear of the rebox. (Fig. 1).
6. Re-secure the adjustement screws to hold the thermal disc bracket in place.
note:
For optimal perfomance, the thermal disc MUST make contact with the rebox.
EPT70
/