Minka Group F831L-FLR User manual

Type
User manual
Tear
©2018 Minka Lighting Inc.Manual design and all elements of manual design are protected by United States Federal and/or State Law including
Patents, Trademark, and/or Copyright Laws.
F831L
INSTALLING THE LIGHT KIT
8
9
0
DC8 FAN
wattage
D.
light kit hardware
5/32*7mm+S(4 pcs)
1. Fan Body
2. LED assembly
3. coupler cover
4. Fan blade(3 pcs)
5. Canopy
6. light kit plate
7. light shade
8. downrod assembly
9. hanger bracket
10. canopy cover
11. hand held remote
with 2 screws(include
batteries)
12. receiver(include 6 wire nuts)
A Fan blades attachment screw
1/4*16mm+S screw(10 pcs)
#8-18*19mm screw(4 pcs)
1/4(Φ6.6*13*0.8mmflat
washer(10 pcs)
Step 1: Assemble the 3 blades together with the
provided blade attachment screw. (Fig. 5)
Step 2: Install the blade assembly to the motor .
ATTACHING THE FAN BLADE
Fig.5 Fig.6
,and slip the coupler cover on to the fan body.
7
8
9
2
hanger
0
Fig.7 Fig.8 Fig.9 Fig.10 Fig.11 Fig.12
Fig.14
5
4
Fig.15 Fig.16
Motor to Receiver electrical connections: connect the WHITE
WIRE from the fan to the WHITE wire from receiver. Connect the RED wire
from the fan to the RED wire from the Receiver. Connector the BLUE wire
from the fan to the BLUE wire from the recelver. connect the PURPLE
wire from the fan to the PURPLE wire from the receiver. Connect the
GREY wire from the fan to the GREY wire from the receiver.
Step 4 Receiver to House Supply Wires Electrical connections: Connect
the WHITE wire from the outlet box to the WHITE wire from the receiver.
Connect the BLACK wire from the outlet box to the BLACK wire from the
receiver. Secure all wire connections with the plastic wire nuts provided.
4
Downrod
Hanger
Bracket
White
White
Red
Blue
Purple
Grey
Green wire
Black
Fig.17 Fig.18 Fig.19
7
8
9
Hanger
Bracket
Screw
Receiver
Canopy
Screw
Screw
Canopy
Canopy Cover
cover
INSTALLING THE LIGHT KIT
Step 1: Remove 1 of 3 screws on light kit adapter and loosen
the other 2 screws.(Fig. 20)
Step 2: Slide the light kit plate up towards the light kit adapter and
place the key holes over the screws on the light kit adapter. Turn
light kit plate until it locks in place at the narrow section of key holes.
(Fig. 21)
Step 3: Align the round hole of the light kit plate with light kit adapter,
tighten all 3 screws.(Fig. 22)
Step 4: Connect the wires between the fan and LED assembly with
the connectors.(Fig. 23)
Step 5: Tighten the LED assembly to light kit plate with 3 screws.
(Fig. 24)
Step 6: Align the slot of the light shade with the aised dimple on the
light kit plate and turn it clockwise until it stops.(Fig. 25)
Fig.20 Fig.21 Fig.22 Fig.23 Fig.24 Fig.25
wattage
9
(COUNTERCLOCKWISE DIRECTION)
(CLOCKWISE DIRECTION)
Fig.26 Fig.27
26
27
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Minka Group F831L-FLR User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI