Supermicro BPN-SAS3-842TQ User manual

Brand: Supermicro

Model: BPN-SAS3-842TQ

Type: User manual

Rev. 1.0

BPN-SAS3-842TQ Backplane

USER'S GUIDE

BPN-SAS3-842TQ Backplane User's Guide

Manual Revision 1.0

Release Date: February 28, 2019

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

and makes no commitment to update or to keep current the information in this manual, or to notify

any person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and docu-

mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.

Any use or reproduction of this product is not allowed, except as expressly permitted by the terms

of said license.

IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, SPECULATIVE, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR

INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POS-

SIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL NOT

HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE

PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING,

OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall be

the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims

will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A

digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the manufacturer’s instruction manual, may cause harmful interference

with radio communications. Operation of this equipment in a residential area is likely to cause harm-

ful interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-

ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document. Information in this document is subject to change without notice.

Other products and companies referred to herein are trademarks or registered trademarks of their

respective companies or mark holders.

Printed in the United States of America

WARNING: This product can expose you to chemicals including

lead, known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information, go

to www.P65Warnings.ca.gov.

The products sold by Supermicro are not intended for and will not be used in life support systems,

medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com-

munication devices, or other critical systems whose failure to perform would be reasonably expected

to result in signicant injury or loss of life or catastrophic property damage. Accordingly, Supermicro

disclaims any and all liability, and should buyer use or sell such products for use in such ultra-

hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indem-

nify, defend, and hold Supermicro harmless for and against any and all claims, demands, actions,

litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

iii

Preface

Table of Contents

Contacting Supermicro ....................................................................................... iv

Returning Merchandise for Service.....................................................................v

Chapter 1 Safety Guidelines ....................................................................1-1

1-1 ESD Safety Guidelines ................................................................................... 1-1

1-2 General Safety Guidelines .............................................................................. 1-1

1-3 An Important Note to Users ............................................................................ 1-2

1-4 Introduction to the BPN-SAS3-842TQ Backplane .......................................... 1-2

Chapter 2 Connectors and Pin Denitions .............................................2-1

2-1 Front Connectors ............................................................................................ 2-1

2-2 Front Connector Pin Denitions ...................................................................... 2-2

2-3 Front Jumper Locations and Pin Denitions ................................................... 2-3

2-4 Rear Connectors and LED Indicators ............................................................. 2-4

BPN-SAS3-842TQ Backplane User's Guide

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8226-1900

Preface

Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-

fore any warranty service will be rendered. You can obtain service by calling your

vendor for a Returned Merchandise Authorization (RMA) number. When returning

to the manufacturer, the RMA number should be prominently displayed on the

outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and

handling charges will be applied for all orders that must be mailed when service

is complete.

For faster service, RMA authorizations may be requested online (http://www.super-

micro.com/support/rma/).

Whenever possible, repack the backplane in the original Supermicro box, using the

original packaging materials. If these are no longer available, be sure to pack the

backplane in an anti-static bag and inside the box. Make sure that there is enough

packaging material surrounding the backplane so that it does not become damaged

during shipping.

This warranty only covers normal consumer use and does not cover damages in-

curred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

During the warranty period, contact your distributor rst for any product problems.

1-1

Chapter 1: Safety Guidelines

Chapter 1

Safety Guidelines

To avoid personal injury and property damage, carefully follow all the safety steps

listed below when accessing your system or handling the components.

1-1 ESD Safety Guidelines

Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent dam-

age to your system, it is important to handle it very carefully. The following measures

are generally sucient to protect your equipment from ESD.

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing a component from the antistatic

bag.

• Handle the backplane by its edges only; do not touch its components, peripheral

chips, memory modules, or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the card and peripherals back into their antistatic bags when not in use.

1-2 General Safety Guidelines

• Always disconnect power cables before installing or removing any components

from the computer, including the backplane.

• Disconnect the power cable before installing or removing any cables from the

backplane.

• Make sure that the backplane is securely and properly installed on the mother-

board to prevent damage to the system due to power shortage.

1-2

BPN-SAS3-842TQ Backplane User's Guide

1-3 An Important Note to Users

• All images and layouts shown in this user's guide are based upon the latest PCB

revision available at the time of publishing. The card you have received may or

may not look exactly the same as the graphics shown in this manual.

1-4 Introduction to the BPN-SAS3-842TQ Backplane

The BPN-SAS3-842TQ backplane has been designed to utilize the most up-to-date

technology available, providing your system with reliable, high-quality performance.

Always refer to the Supermicro Web site at www.supermicro.com for the latest

updates, compatible parts, and supported congurations.

2-1

Chapter 2: Connectors and Pin Denitions

Chapter 2

Connectors and Pin Denitions

2-1 Front Connectors

1. Sideband Connector #2 (8-pin):

SGPIO, JP6

2. Sideband Connector #1 (8-pin):

SGPIO, JP1

3. JTAG Connector (7-pin): J11,

CPLD Upgrade Port

4. Chip: CPLD

5. Power Connector (4-pin) #1:

JPW1

6. Power Connector (4-pin) #2:

JPW2

7. SAS/SATA Port #4: J10

8. SAS/SATA Port #3: J9

9. SAS/SATA Port #2: J8

10. SAS/SATA Port #1: J7

11. SAS/SATA Port #0: J6

Figure 2-1. Front Connectors

2-2

BPN-SAS3-842TQ Backplane User's Guide

2-2 Front Connector Pin Denitions

#3. CPLD Upgrade Port

The CPLD programming port, designated

J11, is used only by the manufacturer to

upgrade the CPLD.

#4. CPLD Chip

The CPLD is an enclosure management

chip that supports the SGPIO and LED

management.

Sideband Connectors

(Sideband#1 and Sideband#2)

Pin Denition Pin Denition

2 SDataIn

(SGPIO Data

In)

1 N/C

4 SDataOut

(SGPIO Data

Out)

3 GND

6 GND 5 SLoad

(SGPIO Load)

8 N/C 7 SClock

(SGPIO Clock)

#1 - 2. Sideband Connectors

These are the SGPIO sideband connectors

for SAS/SATA. SGPIO Sideband #1,

designated J1, is for SAS/SATA Ports #0-3

and SGPIO Sideband #2, designated J6, is

for SAS/SATA Port #4.

#5. - 6. Backplane Main Power Connectors

The 4-pin connectors, designated JPW1

and JPW2, provide power to the backplane.

See the table on the right for pin denitions.

#7. - 11. MiniSAS 7-Pin Connectors

The SAS ports are used to connect the SAS

drive cables. The ve ports are designated

J6, J7, J8, J9, and J10. Each port is also

compatible with SATA drives. However,

mixing SAS and SATA drives in the same

enclosure is not recommended.

Backplane

Main Power

4-Pin Connector

Pin# Denition

1 +12V

2 and 3 Ground

4 +5V

2-3

Chapter 2: Connectors and Pin Denitions

2-3 Front Jumper Locations and Pin Denitions

Figure 2-2. Front Jumpers

Explanation of Jumpers

To modify the operation of the backplane,

jumpers can be used to choose between

optional settings. Jumpers create shorts

between two pins to change the function

of the connector. Pin 1 is identied with

a square solder pad on the printed circuit

board.

Note: On two pin jumpers, "Closed" means

the jumper is on and "Open" means the

jumper is o the pins.

Connector

Pins

Jumper

Setting

3 2 1

Jumper Settings

Jumper Jumper Settings Note

ACTLED Open: Default This is used for internal testing only.

ACTLED

2-4

BPN-SAS3-842TQ Backplane User's Guide

2-4 Rear Connectors and LED Indicators

SAS#0

SAS#1

SAS#3

SAS#4

ACT#0

FAIL#0

SAS#2

Rear SAS3/SATA Connectors

Rear Connector SAS3 Drive Number

SAS #0 SAS3/SATA HDD #0

SAS #1 SAS3/SATA HDD #1

SAS #2 SAS3/SATA HDD #2

SAS #3 SAS3/SATA HDD #3

SAS #4 SAS3/SATA HDD #4

Rear LED Indicators

Rear LED Hard Drive Activity Failure LED

SAS #0 ACT #0 FAIL #0

SAS #1 ACT #1 FAIL #1

SAS #2 ACT #2 FAIL #2

SAS #3 ACT #3 FAIL #3

SAS #4 ACT #4 FAIL #4

Figure 2-3. Rear Connectors

ACT#1

ACT#2

ACT#4ACT#3

FAIL#4FAIL#3FAIL#2

FAIL#1

2-5

Chapter 2: Connectors and Pin Denitions

Notes

2-6

BPN-SAS3-842TQ Backplane User's Guide

Disclaimer (cont.)

The products sold by Supermicro are not intended for and will not be used in life sup-

port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,

aircraft/emergency communication devices, or other critical systems whose failure to

perform would be reasonably expected to result in signicant injury or loss of life or

catastrophic property damage. Accordingly, Supermicro disclaims any and all liability,

and should buyer use or sell such products for use in such ultra-hazardous applications,

it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend,

and hold Supermicro harmless for and against any and all claims, demands, actions,

litigation, and proceedings of any kind arising out of or related to such ultra-hazardous

use or sale.

Supermicro BPN-SAS3-842TQ User manual

Supermicro BPN-SAS3-842TQ User manual

Supermicro BPN-SAS3-842TQ User manual

Related papers

Other documents