Metrologic Eclipse MS5145-11 User manual

Brand: Metrologic

Model: Eclipse MS5145-11

Category: Bar code readers

Type: User manual

This manual is also suitable for

LOCATIONS

CORPORATE HEADQUARTERS

North America Metrologic Instruments, Inc. Customer Service: 1-800-ID-METRO

90 Coles Road Tel: 856-228-8100

Blackwood, NJ 08012-4683 Fax: 856-228-6673

Email: [email protected]

Internet: www.metrologic.com

EUROPEAN HEADQUARTERS

Germany, Metrologic Instruments GmbH Tel: +49 (0) 89 89019 0

Middle East and Africa Dornierstrasse 2 Fax: +49 (0) 89 89019 200

82178 Puchheim b. Email: info@europe.metrologic.com

Munich, Germ any

Spain Metrologic Eria lbérica SL Tel: +34 913 272 400

Julián Camarillo, 29 D-1 Fax: +34 913 273 829

Edificio Diapasón Email: [email protected]

28037 Madrid

Italy Metrologic Italia Srl Tel: +39 0 51 6511978

Via Emilia 70 Fax: +39 0 51 652 1337

40064 Ozzano dell’Emilia (BO) Email: [email protected]

France Metrologic Eria France SA Tel: +33 (0) 1 48.63.78.78

69 Rue de la Belle Etoile Fax: +33 (0) 1 48.63.24.94

ZI Paris Nord II, BP 50057 Email: [email protected]

95947 – ROISSY CDG CEDEX

United Kingdom Metrologic Instruments UK Limited Tel: +44 (0) 1256 365900

58 Tempus Business Centre Fax: +44 (0) 1256 365955

Kingsclere Road, Basingstoke Email: info@uk.metrologic.com

Hampshire RG21 6XG

ASIA

Singapore Metrologic Asia (Pte) Ltd Tel: 65-842-7155

No.8 Kaki Bukit Place Fax: 65-842-7166

Floor Email: [email protected]ic.com

Singapore 41618 6

China Metro (Suzhou) Technologies Co., Ltd. Tel: 86-512-62572511

221 Xing Hai Street Fax: 86-512-62571517

Suzhou Industrial Park Email: info@cn.metrologic.com

Suzhou, China

215021

Japan Metrologic Japan Co., Ltd. Tel: 81-3-3839-8511

Matsunoya Building, 6 Floor Fax: 81-3-3839-8519

3-14-8 Higashiueno Taitou-Ku Email: i[email protected]ogic.com

Tokyo 110-0015, Japan

SOUTH AMERICA

Brazil Metrologic do Brasil Ltda. Tel: 55-11-5182-8226

Rua da Paz 2059 Fax: 55-11-5182-8315

CEP 04713-002 Email: info@br.metrologic.com

Chácara Santo Antônio

São Paulo, SP, Brasil

Outside Brazil Metrologic South America Tel: 55-11-5182-7273

Rua da Paz 2059 Fax: 55-11-5182-7198

CEP 04713-002 Email: info@sa.metrologic.com

Chácara Santo Antônio

São Paulo, SP, Brasil

OPYRIGHT

in any form or by any means without prior written consent, except by reviewer, who may quote brief passages in a review,

or provided for in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of their respective companies.

iii

TABLE OF CONTENTS

Introduction........................................................................................................... 1

Accessories and Supplies .................................................................................... 2

Quick Start............................................................................................................ 3

Standard Scanner Installation .............................................................................. 4

Keyboard Wedge Scanner Installation ................................................................. 5

USB Scanner Installation...................................................................................... 7

Disconnecting the PowerLink Cable from the Scanner ........................................ 8

Scanner Parts....................................................................................................... 9

Audible Indicators ............................................................................................... 10

Visual Indicators ................................................................................................. 11

Failure Modes ..................................................................................................... 12

Scan Area........................................................................................................... 13

Labels ................................................................................................................. 14

Troubleshooting Guide ....................................................................................... 15

RS-232 Demonstration Program ........................................................................ 19

Maintenance ....................................................................................................... 19

Appendix A

Specifications ................................................................................................. 20

Appendix B

Default Settings .............................................................................................. 22

Appendix C

Scanner Pinout Connections .......................................................................... 27

Cable Connector Configurations .................................................................... 29

Appendix D

Warranty and Disclaimer ................................................................................ 31

Appendix E

Notices ........................................................................................................... 31

Appendix F

Patent Information .......................................................................................... 33

Index................................................................................................................... 34

INTRODUCTION

The MS5145 Eclipse is a singl e-line, hand-held laser scanne r.

Equipped with Metrologic’s patented CodeGate technol ogy, Eclipse can be

used in a wide variety of applications. Cod eGate technology allows the user to

easily target the desired bar cod e and complete the data transmission with a

simple press of a button. This combination mak es Ecli pse a perfect selection

for menu scanning, point-of-sale, docum ent processing and inventor y control.

With Metrologic’s state-of-the-art scanning technolog y embe dded inside, the

MS5145 Eclipse has a longer working range and a wider scan field than a

typcial CCD. The width of the scan line grows as the scanner moves further away

from bar codes. In addition, the laser beam pulses making lining up bar codes

easy, and when the scanner senses a b ar code (CodeSense™ Mode), the laser

beam automatically s witches to scan mode and activates CodeGate to ensure

high-speed scanning a nd acc uracy.

Many of the standard features include: PowerLink User-replaceable cables, Bits

‘n’ Pieces™ data editing, User Fr ie ndly Programming using MetroSel ect™ bar

codes, or MetroSet 2 Windows-based configur ation utility.

Eclipse Interface

MS5145-9*

OCIA*

MS5145-11

IBM 468X/469X

MS5145-41 Full RS-232/Light Pen Emulation

MS5145-37 USB/Keyboard Wedge

* At the time this manual was printed, the OCIA version of the scanner was not

available.

ACCESSORIES AN D SUPPLIES

The following is a list of parts that may or may not be included in the MS514 5 kit.

• Eclipse MS5145 Single-Line Las er Scanner

• AC to DC Power Transformer – Regulated 5.2VDC @ 650 mA output

• One of the following may be included:

• 120 V United States [

MLPN 45-45593 ]

• 220 V - 240 V Continental European [

MLPN 45-45591 ]

• 220 V – 240 V United Kingdom [ MLPN 45-45592 ]

• PowerLink Cable

• One of the following may be include d:

• RS232 Cable: 2.1m (7’) straight cord, long bend relief , with built-in

power jack [

MLPN 55-55000A ]

• AT/PS2/XT Keyboard Cable: 2.4m (8’) straight cord, long bend

relief, with built-in power jack [

MLPN 55-55002A ]

• PS2 Keyboard Cable: 2.4m (8’) straight cord, long bend re lief, with

built-in power jack [ MLPN 55-55142A ]

• PS2 Keyboard Cable: 1.5m (5’) straight cord, long bend re lief,

without built-in power jack [

MLPN 55-55166A ]

• Stand Alone Keyboard Cable: 2.1m (7’) straight cor d, long bend

relief, with built-in power jack [ MLPN 55-55020A ]

• Stand Alone Keyboard Cable: 1.5m (5’) straight cor d, long bend

relief, without built-in po wer jack [

MLPN 55-55164A ]

• USB Cable: 1.5m (5’) straight cord, long bend relief, without built-in

power jack [ MLPN 55-55165A ]

• Installation and User’s Guide [

MLPN 70-79001]

• MetroSelect Single Line Configuration Guide [ MLPN 00-02544 ]

Other items may be ordered for the specific protocol being used. T o order

additional items, contact the dealer, distributor or your l oca l Metrologic

representative.

QUICK START

1. Connect the 10-pin RJ45 plug into the j ack on the Eclipse MS5145. You

will hear a ‘click’ when the connectio n is made.

2. Connect the L-shaped plug of the po wer supply into the power jack on the

PowerLink cable.

3. Connect the power supply into an AC o utlet. Make sur e the AC input

requirements of the power supply match the AC outlet.

(See caution statement below)

4. When the MS5145 is ready to scan, the green LED will turn on, the red LED

will flash and the scanner will beep once.

5. The MS5145‘s operation is automatic. The laser puls es on and off. The

green LED remains on during n orma l puls e operation and it blinks during

power save mode.

Operational Test

6. Place a bar code in front of the scanning window. While a iming at the bar

code with the blinking laser bea m, press the Cod eGate button, scanner will

beep once and flash the red LED if the b ar code was successfully decoded.

7. The scanner is shipped from the factory programmed with default settings.

To configure the MS5145 scanner to meet the host s ystem’s specific ne eds,

refer to the Programming Guide or custom configurati on guide for

instructions on how to change the scanners def ault settings.

Caution:

To maintain compliance with federal regulations 21 CFR, Part 1040.10, section (f)(6) the scanner

must be plugged into an electrical outlet with a switch accessible to the user or be powered by a host

system containing a switch that will disable power to the scanner.

STANDARD RS232 SCANNER INSTALLATION

1. Turn off the host system.

2. Connect the 10-pin RJ45 plug of the Po werLink cable into the jack on the

MS5145 RS232 scanner.

Note: If the MS5145 is receiving power from the host system, skip to step

#5. (See caution statement below*)

3. Connect the L-shaped plug of the po wer supply into the power jack on the

PowerLink cable. (See caution statement below**)

4. Make sure the AC input requirements of the power supply match the AC

outlet. Connect the power supply into an AC outlet.

5. Connect the PowerLink cable to the proper port on the host system.

6. Turn on the host system

7. When the MS5145 is ready to scan, the gree n LED will turn on, the red LED

will flash and the scanner will bee p once.

Manufacturer’s Note:

Plugging the scanner into a port on the host system does not gu arantee that the

scanned information will be communic ated properly to the host system. The

scanner and/or the host system may need to be configured for comm unic ations

to occur.

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet

the requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

*To maintain compliance with standard CSA C22.2 No. 60950/UL 60950 and norm EN 60950, the

power source should meet applicable performance requirements for a limited power source.

**To maintain compliance with federal regulations 21 CFR, Part 1040.10, section (f)(6) the scanner

must be plugged into an electrical outlet with a switch accessible to the user or be powered by a host

system containing a switch that will disable power to the scanner.

KEYBOARD WEDG E SCANNER INSTALLATION

1. Turn off the host system.

2. Connect the 10-pin RJ45 plug of the Po werLink cable into the jack on the

MS5145.

3. Disconnect the keyboard from the host system.

4. Connect the L-shaped plug of the po wer supply into the power jack on the

PowerLink cable (refer to the manufacturer’s recommendation and Note on

page 6).

5. Make sure the AC input requirements of the power supply match the AC

outlet. Connect the power supply into an AC outlet (see caution statement

on page 6**).

6. The PowerLink “Y” cable is terminated with a 5-pin DIN female con nector o n

one end, and a 6-pin mini DIN male on t

KEYBOARD WEDG E INSTALLATION (CONTINUED)

Manufacturer’s Recommendation

If the keyboard port of the host system cannot supply enough current, the use of

an external power supply with the MS5145 Keybo ard W ed ge wil l be necessary.

Powering the MS5145 directly from the computer keybo ard connector could

interfere with the operation of the scanner or the c omputer. Not all computers

supply the same current through the keybo ard port, so a scanner may work on

one computer and not another (see caution statement on page 5).

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet

the requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

*To maintain compliance with standard CSA C22.2 No. 60950/UL 60950 and norm EN 60950, the

power source should meet applicable performance requirements for a limited power source.

**To maintain compliance with federal regulations 21 CFR, Part 1040.10, section (f)(6) the scanner

must be plugged into an electrical outlet with a switch accessible to the user or be powered by a host

system containing a switch that will disable power to the scanner

Note: The center of the L-Shaped plug of the power supply is negative (“-“).

USB SCANNER INSTALLATION

1. Connect the 10-pin RJ45 plug of the Po werLink cable into the jack on the

MS5145 USB scanner.

Note: The MS5145 USB scanner will receive power directly from the host

system; no external power supply is required.

2. Connect the USB connector of the PowerLink cable into the USB port of the

host system.

3. When the MS5145 is ready to scan, the gree n LED will turn on, the red LED

will flash and the scanner will beep once.

DISCONNECTING THE POWERLINK CABLE F ROM THE SCANNER

Before removing the cable from the scanner, Metrologic recomme nds that the

power on the host system is off and the power supply has been discon nected

from the PowerLink cable.

1. Locate the small ‘pin-hole’ on the back of the scanner.

2. Bend an ordinary pap erclip into the shape shown a bove.

3. Insert the paperclip (or other small metallic pin) into the small ‘ pin-hole’.

4. You will hear a faint ‘click’. Pull gentl y on the strain-rel i ef of the PowerLink

cable and it will slide out of the scanner.

SCANNER PARTS

1. Green & Red LEDs

The MS5145’s laser pulses on an d off when no bar code is presented, and

stays on when it senses a bar code. The green LED remains o n dur ing

normal pulse and scanning ope ration, and it blinks during power sav e mode.

On a successful read of a bar code, the red LED will flash and th e scan ner

will beep once. The LEDs are also use d as dia g nostic indicators and mode

indicators.

2. Output Window

Laser Light emits from this aperture.

3. PowerLink Cable

The 10-pin modular plug on the P owerLink cable connects into the 10-pin

modular jack on the MS5145.

AUDIBLE INDICATORS

When the MS5145 scanner is operatio nal, it provides audible feedback. T hese

sounds indicate the status of the scanner. Eight settings are availa ble for the

tone of the beep (normal, 6 alternate tones and n o tone). T o change the tone,

refer to the Configuration Guide.

One Beep – on power up

The green LED will turn on, then the red LED wil l flash and the

scanner will beep once. T he red LED will remain on for the

duration of the beep. The scanner is no w ready to scan.

One Beep – during operation

When the scanner successfully r eads a bar code, the red LED

will flash and the scanner will beep once (if programmed to do

so). If the scanner does not beep once and the red l ight does

not flash, then the bar code has not been successfull y read.

Three Beeps – during operation

When entering the program mode, the red LED will flash while

the scanner simultaneous l y beeps three times. The red LED

will continue to flash until the unit exits program mode. Upo n

exiting program mode, the scanner will beep three times and

the red LED will stop flashing.

When configured for communication time out, 3 bee ps during

operation will indicate that a communic ation timeout has

occurred.

Three Beeps – on power up

This is a failure indicator. Refer to the Failure Modes section

of this guide on page 11.

Razzberry Tone

This is a failure indicator or an invalid cod e read during

program mode. Refer to the Failure Modes section of this

guide on page 12.

VISUAL INDICATORS

There is a red LED and a green LE D on the MS5145. When the scanner is on,

the activity of the LEDs indicates the status of the current scan and the scanner.

Green and Red LEDs are off

The LEDs will not be illuminated if the scanner is not receiving

power from the host or transformer.

Steady Green

Indicates normal pulse or continuous las er operation.

Accompanied by a razzberry tone, it indicates that an inv alid

bar code has been scanned.

Flashing Green

After a period of inactivity, the ON time of the pulsing laser will

be shortened. During this time the green LED will flash. This

indicates that the scanner is in a power saver mode. When a

bar code enters the laser field, the scanner will wake up and

return to normal pulse mode.

Steady Green and Single Red Flash

When the scanner successfully r eads a bar code, the red LED

will flash and the scanner will beep. If the red LED does not

flash and the scanner does not beep, then the b ar cod e has

not been successfully read.

Steady Green and Steady Red

After a successful read, the scanner transmits the data to the

host device. Some communication modes require that the host

inform the scanner when data is ready to be rec eived. If the

host is not ready to accept the information, the scanner’s red

LED will remain on until the data can be transmitte d.

Steady Green and Continuous Flashing Red

When entering the program mode, the red LED will flash, the

green LED will turn on and the scanner will beep three times.

The red LED will continue to flash and th e green LED will stay

on until the unit exits the program mode.

FAILURE MODES

One Razzberry Tone on Power-up

This indicates the scanner has experi enced a laser or flipper

subsystem failure. Return the unit for repair to a Metrologic

Authorized Service Center.

Continuous Razzberry Tone with all LEDs off

If, upon power up, the scanner emits a continuous razzberry

tone, then the scanner has an experienced an e lectron ic

failure. Return the unit for repair to a Metrologic Authorized

Service Center.

Three Beeps – on power up

If the scanner beeps 3 times on power up then, the non-volatil e

memory (NovRAM) that holds the scanner configur ation has

failed. Return the unit for repair to a Metrologic Authorize d

Service Center.

SCAN AREA

Minimum Bar Code Element Width

ABCDEF

mm .10 .12 .17 .26 .33 .66

mils 4.1 4.8 6.8 10.4 13 26

LABELS

Each scanner has one label on the unders ide of the unit. This label has the

model number, date of manufacture, serial number, laser and caution

information. The follo wing is an e xample of this l abel.

Patent Information-See Manual

FCC and ICES-003 Information-See Manua l

Warranty VOID if case opened.

Contains no user serviceable com po nents.

Complies with 21 CFR 1040.10 & 10 40.11

IEC 60825-1:1993+A2:2001

TROUBLESHOOTING GUIDE

The following guide is for referenc e purp oses only. Contact a Metrologic

representative to preserve the limite d warranty terms on page 31.

SYMPTOMS POSSIBLE CAUSE(S)SOLUTION

No LEDs, beep

or laser line

No power is being supplied to

the scanner

Check transformer,

outlet and power strip.

Make sure the cable is

plugged into the

scanner.

No LEDs, beep

No power is being supplied to

the scanner from host

Some host systems

cannot supply enough

current to power the

MS5145. Use the

proper power supply.

3 beeps on

power up

Non-volatile RAM failure

Contact a Metrologic

Representative, if the

unit will not hold the

programmed

configuration.

Continuous razz

tone on power up

RAM or ROM failure

Contact a Metrologic

Representative.

Razz tone at

power up

VLD failure or a Scanner

flipper failure

Contact a Metrologic

Representative.

Unit scans,

Communicates

and beeps twice

Same Symbol timeout set too

short

Adjust same symbol time

out for a longer time.

The unit powers

up but does not

beep

Beeper disabled. No tone

selected

Enable beeper. Select

tone.

TROUBLESHOOTING GUIDE (CONTINUED)

SYMPTOMS POSSIBLE CAUSE(S)SOLUTION

The unit powers

up, but does not

scan

Scanning a particular

symbology that is not

enabled

UPC/EAN, Code 39,

Interleaved 2 of 5, Code 93,

Code 128 and Codabar are

enabled by default. Verify that

the type of bar code being

read has been selected.

The unit powers

up, but does not

scan and/or beep

The scanner has been

programmed for a

character length lock, or

a minimum length and

bar code being scanned

does not satisfy the

programmed criteria

Verify that the bar code that is

being scanned falls into the

criteria (Typical of Non-

UPC/EAN codes.) The

scanner defaults to a minimum

of 3 character bar code.

The unit scans a

bar code, but

locks up after the

first scan and the

red LED stays on

The scanner is

configured to support

some form of host

handshaking but is not

receiving the signal

If the scanner is setup to

support ACK/NAK,RTS/CTS,

XON/XOFF) or D/E, verify that

the host cable and host are

supporting the handshaking

properly.

The unit scans,

but the data

transmitted to the

host is incorrect

The scanner’s data

format does not match

the host system

requirements

Verify that the scanner’s data

format matches that required

by the host. Make sure that the

scanner is connected to the

proper host port.

Scanner beeps

at some bar

codes and NOT

for others of the

same bar code

symbology

The print quality of the

bar code is suspect

The aspect ratio of the

bar code is out of

tolerance

Check print mode. The t ype of

printer could be the problem.

Change print settings. For

example change to econo

mode or high speed.

Page is loading ...

Metrologic Eclipse MS5145-11 User manual

Brand: Metrologic

Model: Eclipse MS5145-11

Category: Bar code readers

Type: User manual

This manual is also suitable for

Download PDF

report

Metrologic Eclipse MS5145-11 User manual

This manual is also suitable for

Metrologic Eclipse MS5145-11 User manual

Related papers

Other documents