Ultra Products U12-41498 User manual

Brand: Ultra Products

Model: U12-41498

Type: User manual

Ultra Products U12-41498 allows you to control up to eight A/V components hidden behind closed doors or in a cabinet using your existing IR remote control. It includes an IR receiver, central control hub, four dual IR blasters, and an AC power adapter. Simply place the IR receiver in the line of sight of your remote, mount the IR emitters on your A/V components, and connect the power supply. Enjoy convenient control of your home theater system without the hassle of direct line-of-sight aiming.

IR Repeater

U12-41498

USER MANUAL

Introduction

The Ultra IR Repeater allows you to use an existing infrared (IR) remote

control to operate up to eight audio/video (A/V) components located be-

hind closed doors or in an entertainment or equipment closet.

What’s Included:

• IR Receiver

• AC Power Adapter

• Central Control Hub

• (4) 2-Device IR Blasters

Installation:

1. Place the IR Repeater box on a flat surface in your entertainment

cabinet or equipment closet (secure with the included adhesive if

necessary).

2. Connect the IR Receiver to the IR Repeater Box.

3. Mount the IR Receiver to the optimal line-of-sight position on your

entertainment furniture. Ensure the “eye” is facing the area where

the remote will be used from.

a) Make sure the receiver is mounted at least 1ft away from your

television (to avoid interference) and no longer than 12ft from the

IR Repeater Box (as this is the length of the IR Receiver cable).

b) Suggested mounting locations include: on a shelf, exposed part

of an entertainment cabinet or behind a speaker grille.

4. Connect the IR Emitter(s) to the IR Repeater Box.

5. Locate the IR “eye” of each A/V component you wish to control.

a) If you can’t easily locate the “eye”, use a flashlight to shine light

through the front panel of the components; the eye is a small red

disc, approximately 1/8’ in diameter.

6. Once located, remove the adhesive tape cover from the emitter’s

clear tape and attach one IR Emitter to the IR “eye” of each A/V

component to be controlled.

a) Note that these are dual emitter cables so that two components

can be controlled by each cable (four cables included).

7. Connect the power supply to the IR Repeater box and then insert

the plug end into any standard 110-240VAC outlet.

8. Verify operation by turning your system components ON using your

existing IR remote controls.

Using the Hidden IR

Instead of aiming at your equipment, point the remote to the IR receiver

and use as you would normally.

The LED light on the IR Receiver will blink when you use your remote

control(s), confirming the system is working properly.

Ultra Products

8300 West Flager St.

Suite# 121-106

Miami, FL 33144

Technical Support:

1(888) 222-5487

www.ultraproducts.com

Notes

• Some A/V components, such as high-powered amplifiers and receivers, may

require additional ventilation and will overheat in an enclosed cabinet. Check

the components’ manuals prior to enclosing them fully.

• Keep the IR receiver away from plasma screens and devices that emit too

much low-frequency RF or an excess of ambient light, including direct sunlight,

floodlights, and some halogen or fluorescent lamps as they interfere with the

signals.

• Avoid attaching the IR emitter cables to equipment doors and slots that may

need to be opened or accessed from time to time.

• You can also attach the IR emitters to a shelf within 3” of the components’ IR

eye. This will allow IR control without having to attach the IR emitter to directly

to your components.

• Non-user serviceable parts. Do not attempt to open the power supply or IR

repeater box. Doing so will void your warranty.

• The Hidden IR is not weather-resistant. Do not expose this system to moisture.

Ultra Products U12-41498 User manual

Brand: Ultra Products

Model: U12-41498

Type: User manual

Download PDF

report

Ultra Products U12-41498 User manual

Ultra Products U12-41498 User manual

Other documents