GB-1 GB-2 GB-3
UNPACKING
Remove all packaging from the unit. Retain the packaging. If you dispose of it
please do so according to local regulations.
The following items are included:
• The Main Unit
- The Protective Cap (P.N.: L2MS10-002)
- The Outer Foil (P.N.: L2MS10-003)
- The Foil Frame (P.N.: L2MS10-004)
- The Inner Cutter (P.N.: L2MS10-005)
• The Cleaning Brush (P.N.: L2MS10-006)
• The Travel Case (P.N.: L2MS10-007)
• The Instruction Manual (P.N.: L2MS10-001)
If items are missing, or damaged please contact Partmaster (UK only).
Tel: 0870 6001 338 for assistance.
FIRST TIME USE
The shaver requires a little time to get used to, because your skin and beard
need about a month to adjust to any new shaving method.
PRODUCT OVERVIEW
INSTALLING BATTERIES
1. Put the protective cap on the shaver (to prevent damage to the outer foil).
2. Open the battery cover in the direction of the arrow, insert two AA batteries
into the battery slot following the polarity indicators inside. Reattach the
battery cover.
3. Do not combine an old battery with a new one, or use dierent types of
batteries together.
4. If the shaver will not be used for a long period of time, please remove the
batteries.
MAINTENANING THE CUTTING SYSTEM
1. It is recommended that you replace the outer foil at least every year and the
inner cutter ar least every two years to maintain your shaver’s cutting
performance.
2. Turn the shaver o before replacing the outer foil and the inner cutter.
3. Remove the batteries from the compartment.
• Replacing the outer foil :
Squeeze the foil frame release button and lift the outer
foil block upwards to remove it. Remove the outer foil
from the frame by slipping it o the hooks. Slip the new
outer foil into the frame with the plastic edge facing
inward. Guide the plastic edges onto the hooks in the
frame.
• Replacing the inner cutter :
Remove the outer foil block. Remove the inner cutter by
grasping it rmly at both ends and pulling it straight
away from the shaver. To insert the new inner cutter,
hold the cutter at both ends and press downwards until
its snaps onto the shaver.
1
2
3
4
5
Protective Cap
Outer Foil
Foil Frame
Inner Cutter
Foil Frame Release Button
6
7
8
9
10
Power Switch
Lock Release Button
Battery Cover
Cleaning Brush
Travel Case
1
3
6
7
8
4
5
10
9
OPERATION
1. Remove the protective cap.
2. Press the lock release button to unlock the power
switch. Then switch on the shaver on by pushing the
switch upwards.
3. Hold the shaver at a right angle (90º) to your skin. Start
shaving by applying gentle pressure to your face.
Stretch your skin with your free hand, move the shaver
back and forth in the direction of your beard. You may
gently increase the amount of pressure as your skin
becomes accustomed to this shaving method.
Applying excessive pressure will not provide a closer
shave.
4. Switch the shaver o by pushing the switch downwards.
5. To prevent damage to the foil and inner cutter, replace the protective cap
every time you have nished using the shaver.
90˚
90˚
CLEANING AND MAINTENANCE
1. Switch o the shaver.
2. Push the foil frame release button and detach the foil frame as shown.
3. Grasp inner cutter rmly at each side, and pull straight up.
4. Clean away the clippings with the cleaning brush provided.
5. Reassemble the shaver parts in the reverse order.
• Improper or incorrect use of batteries may cause corrosion or battery
leakage, which could cause re, personal injury or damage to property.
• Use only the types of the batteries which are indicated in this manual.
• When the batteries are exhausted, the shaver will not function. Replace
both batteries at the same time with new ones.
• Do not install new batteries with used ones and do not mix different types
of batteries.
• Do not dispose of used batteries as domestic waste. Dispose of them in
accordance with local regulations.
Handling the Batteries
OFF
Lock
Release
Button
Power
Switch
OFFOFF
OFF OFF
OFF
OFF
2
Becareful of the blades as they are sharp.
Becareful to the inner cutter blades as they are
sharp.