Orbit OBEI50A Owner's manual

Brand: Orbit

Model: OBEI50A

Category: Fitness, gymnastics & weight training

Type: Owner's manual

Orbit OBEI50A: Stay fit and motivated with this feature-rich elliptical trainer. Experience smooth, low-impact workouts with the dual-action handlebars and adjustable stride length. Monitor your progress with the easy-to-use computer that displays time, speed, distance, calories burned, and pulse. The sturdy construction and adjustable resistance levels make this machine ideal for users of all fitness levels.

Owner’s Manual

Table of Contents

Product Safety …………………………………………….. 01.

Part Drawing & Contents ……………………...………….. 02.

Hardware & Tools ………………………………………….. 03.

Assembly …………………………………….…………….. 04.

Adjustment …………………………………….…………….. 10.

Trouble Shooting & Maintenance ……………..………… 11.

Computer ………………………………….……..………… A.

Warm Up ……………………………………..……………. B.

Part List ……………………………………..…………….. C.

Exploded View ……………………………………………. #.

FE150A18-20150422.1

Product Safety

Basic precautions should always be followed, including the following safety instructions when using this

equipment: Read all instructions before using this equipment.

1. Read all the instructions in this manual and do warm up exercises before using this equipment.

2. Before exercise, in order to avoid injuring your muscles, warm-up exercise for every muscle group is highly

recommended. Please refer to the Warm Up pages for pre and post workout.

3. Please make sure all components are not damaged and in working order before use. This equipment should be

placed on a flat surface while in use. Using a mat or other material on the ground is recommended.

4. Please wear proper clothes and shoes when using this equipment; do not wear clothes that might catch in any

part of the equipment.

5. Do not attempt any maintenance or adjustments other than those described in this manual. Should any problems

arise, discontinue use and consult an Authorized Service Representative.

6. Be careful when stepping on or leaving the pedals. Always hold the handlebars first and make sure the pedal at

your side is at its lowest position. Step on the pedal, and stride over the main frame then step on the other pedal.

When using, please hold onto the handlebars. To ensure the pedals run smoothly push or pull on the handlebars

first, then follow with leg motion. When stepping off the machine, make sure one pedal is at its lowest position

and step out of there before stepping out of the pedal at the highest position.

7. Do not use the equipment outdoors.

8. This equipment is for household use only.

9. Only one person should be on the equipment while in use.

10. Keep children and pets away from the product while in use. This machine is designed for adults only. If you feel

any chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately and consult your

physician before continuing.

11. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately and

consult your physician before continuing.

12. The maximum weight capacity for this product is 275 lbs / 125 kgs.

WARNING: Before beginning any exercise program consult your physician. This is especially important for the

persons who are over 35 years old or who have pre-existing health problems. Read all instructions

before using any fitness equipment.

CAUTION: Read all instructions carefully before operating this product. Retain this Owner’s Manual for future

reference.

Part Drawing & Contents

Box Contents

A01 1Set

A09 1Set

A12/A13 2Set

A07 1Set

A08 1Set

Main Frame

Stationary Handlebar

Left/Right

Dual Action Handlebar

Front Stabilizer Tube

Rear Stabilizer Tube

C12/C30 2PC

C24 1PC

C29/C31 2Set

C03/C18 2Set

C06/C27 1Set

Foot Pedal

Water Bottle Holder

Dual Action Arm

Decorative Cover –A/B

Foot Tube Pivot

Decorative Cover –A/B

Hat Cover

Rubber Gasket

D02 1PC

D08 1PC

Computer

AC Adapter

Hardware & Tools

Pack Contents

B01 (1) 6PC

B05 (2) 8PC

B04 (3) 4PC

B12 (4) 4PC

B02 (5) 6PC

Curve Washer

Bolt

Carriage Bolt

Curve Washer

Bolt

B19 (6) 18PC

B09 (7) 4PC

Screw

Nut

(10) 1PC

(8) 1PC

(9) 1PC

Hex Tool with Phillips Screwdriver (13mm/14mm)

Allen Key (M4)

Allen Key (M5)

Assembly

1. Preparation

1.1 Clear a 2 meters time 2.5 meters working space before unpacking your Elliptical Cross Trainer.

1.2 The assembly steps required two persons.

2. Open carton

2.1 Use a sharp knife, open the carton and lay it flat on the floor.

2.2 Remove all loose components.

2.3 Refer to the checklist and check that everything is present.

NOTE:

To protect the Elliptical Cross Trainer while assembling we suggest that you do not remove the protective

packing material until it is absolutely necessary.

3. Remove Rear Protection Tube

3.1 Lift the rear of the machine off the floor and slide a polystyrene block under the rear of the machine.

3.2 Remove Two Bolts [B11], Two Washers [B10] and remove the Protection Tube.

[Remove bolts with the Hex Tool with Phillips Screw Driver provided.]

Assembly

4. Rear Stabilizer Tube Installation

4.1 Assemble the Rear Stabilizer Tube [A08] with Two Bolts [B11] and Two Washers [B10] which were removed from

step 3.2 and tighten firmly.

[Tighten bolts with the Hex Tool with Phillips Screw Driver provided.]

5. Upright Support Tube Installation

5.1 Lift the Upright Support Tube [A02] until it is vertical while the other person connects the matching connectors of

cable [D04/D05] as shown in the illustration below.

5.2 Then slide the Upright Support Tube [A02] into the hole of Main Frame [A01].

5.3 Assemble Six Blots [B02] by fingers, Six Curve Washers [B01] into Main Frame [A01]. Align all bolts slightly then

firmly tighten Six Bolts [B02].

5.4 Slide down the Hat Cover [C06] and push firmly.

[Tighten bolts with the M5 Allen Key provided.]

Attention: Cables can't be folded.

6. Remove Front Protection Tube

6.1 Remove the front polystyrene and place it under the front of the machine to lift it off the floor.

6.2 Refer the step 3 to remove Two Bolts [B11] and Two Washers [B10] from the front of machine and remove front

protection tube.

[Remove bolts with the Hex Tool with Phillips Screwdriver provided.]

D04

D05

C06

A01

A02

B02

B01

A08

B10

B11

A01

Assembly

7. Front Stabilizer Tube Installation

7.1 Assemble the Front Stabilizer Tube [A07] with Two Bolts [B11], Two Washers [B10] which were removed from the

step 6.2 and tighten firmly.

7.2 Remove the polystyrene block and discard.

[Tighten bolts with the Hex Tool with Phillips Screwdriver provided.]

8. Water Bottle Holder Installation

8.1 Remove Two Screws [B16] from Upright Support Tube [A02].

8.2 Align Water Bottle Holder [C24] and fasten with Two Screws [B16] which were removed from step 8.1.

[Remove/Tighten screws with the M4 Allen Key provided.]

9. Stationary Handlebar Installation

9.1 Remove Three Bolts [B23] and Three Curve Washers [B01] from Stationary Handlebar [A09].

9.2 Route Cable [D04] through the bottom of Stationary Handlebar [A09] out the top of Stationary Handlebar [A09],

then slide the Stationary Handlebar [A09] into the opening hole of Upright Support Tube [A02].

9.3 Secure with Three Bolts [B23] and Three Curve Washers [B01] which were removed from step 9.1.

Before tightening make sure the Stationary Handlebar [A09] correctly positioned.

[Remove/Tighten bolts with the M5 Allen Key provided.]

Attention: Cables can't be folded.

B10

B11

A07

A01

A02

C24

B16

A09

B23

B01

D04

A02

Assembly

10. Foot Pedal Installation

10.1 Align the Two Foot Pedal [C12 & C30] and fit to Foot Tube [A05 & A06]. Secure and tighten firmly with Four

Screws [B05].

[Tighten screws with the M4 Allen Key provided.]

11. Dual Action Handlebar Tube Installation

11.1 Insert the Left Dual Action Handlebar Tube [A12] into the top of the Left Dual Action Arm [A03] marked with L

sticker.

11.2 Insert the Right Dual Action Handlebar Tube [A13] into the top of the Right Dual Action Arm [A04] marked with R

sticker.

11.3 Secure with Four Bolts [B04], Four Washers [B12] and Four Nylon Nuts [B09] and tighten firmly but do not over

tighten.

[Tighten nylon nuts with the Hex Tool with Phillips Screwdriver provided.]

12. Decorative Cover Installation

12.1 Assemble One set of Dual Action Arm Decorative Cover –A/B [C29/C31] onto the Left Dual Action Arm [A03]

with Four Screws [B19] and tighten firmly.

12.2 Assemble One set of Dual Action Arm Decorative Cover –A/B [C29/C31] onto the Right Dual Action Arm [A04]

with Four Screws [B19] and tighten firmly.

[Tighten screws with the Hex Tool with Phillips Screwdriver provided.]

A06

C30

B05

C12

A05

A13

A12

A03

A04

B04

B09

B12

C31

B19

C29

C31

A03

A04

Assembly

13. Foot Tube Pivot Decorative Cover Installation

13.1 Assemble One set of Foot Tube Pivot Decorative Cover –A/B [C03/C18] onto Left Foot Tube [A05] with Five

Screws [B19] and tighten firmly.

13.2 Refer the same step to assemble the One set of Foot Tube Pivot Decorative Cover –A/B [C03/C18] onto Right

Foot Tube [A06].

[Remove/Tighten screws with the Hex Tool with Phillips Screwdriver provided.]

14. Computer Installation

14.1 Remove Four Screws [B21] from the bottom of Computer [D02].

14.2 Connect all matching connectors of cables which from Stationary Handlebar [A09] and Computer [D02].

14.3 Slide the extra length cables into the opening hole of Stationary Handlebar [A09].

14.4 There is the computer plate on the top of the Stationary Handlebar [A09]. Position the Computer [D02] on the

computer plate and secure with Four Screws [B21] which were removed from step 14.1.

[Remove/Tighten screws with the Hex Tool with Phillips Screwdriver provided.]

Attention: Cables can't be folded.

A05

C18

C03

B19

D02

B21

A09

Assembly

15. AC Adaptor Installation

15.1 Connect the AC Adaptor (D08) to the Power Supply Cable (D09) on the rear of Main Frame (A01).

15.2 Make sure the specifications of power supply on the Adaptor is correct before plug in.

Plug the other end of the AC Adaptor (D08) into the electrical wall outlet.

D08

A01

D09

Adjustment

Adjusting the Adjustable Foot Pad

Adjust the Adjustable Foot Pad on the Main Frame as needed to level the Elliptical Trainer.

The Elliptical Trainer has to be leveled to prevent from wobble or shaking during the exercise.

Trouble shooting & Maintenance

Trouble Shooting

Computer not working correctly

Check to make sure the computer cable is connected securely.

The Elliptical Trainer wobbles when in use

Adjust the Adjustable Foot Pad on the Main Frame as needed to level the Elliptical Trainer.

Squeaking noise when in use

The bolts may be loose on the Elliptical Trainer, please inspect the bolts and tighten the loose ones.

No, inconsistent, or erratic heart rate reading

Always hold on to the handlebar grip sensors with two hands instead of just one.

Try to maintain moderate pressure while holding onto the hand pulse sensors.

Make sure that the wire connections for the hand pulse sensors are secure.

Maintenance

Cleaning

The Elliptical Trainer can be cleaned with a soft cloth and mild detergent. Do not use abrasives or solvents on plastic

parts. Please wipe your perspiration off the Elliptical Trainer after each use. Be careful not get excessive moisture on

the computer display panel as this might cause an electrical hazard or electronics to fail. Please keep the Elliptical

Trainer, specially, the computer console, out of direct sunlight to prevent screen damage. Please inspect all

assembly bolts and pedals on the machine for proper tightness every week.

Storage

Store the Elliptical Trainer in a clean and dry environment away from children.

Computer

Owner’s Manual of Computer

The monitor is designed for programmable magnetic bike and elliptical trainer and introduced with

the following categories：

- Key Functions

- Displays

- Operating Ranges

- Notice Before Exercise

- Operation Instructions

● Key Functions

There are total 6 keys including UP, DOWN, RESET, START/STOP, RECOVERY, and MODE.

A. UP：To select training mode and adjust function value up.

B. DOWN：To select training mode and adjust function value down.

C. RESET：In stop mode, press the button back to main menu.

D. START/STOP：To start or stop exercise.

E. RECOVERY：To test hear rate recovery status.

F. MODE：In stop mode, the mode is to confirm all exercise data setting, and enter into

program.

● Display

A. Operation：

Power On

Plug in power supply, computer will power on and display all segments on LCD for 2

seconds.

After 4 minutes without pedaling or pulse input, console will enter into power saving mode.

Press any key may wake the console up.

B. Level：

Indicates the level of loading selected from LEVEL 1 to LEVEL 16.

SM2725(26)-71.1-20130802

Computer

C. Loading Profiles：

There are 20 columns of loading bars, and 8 bars in each column. Each column represents

0.1 km workout (without the change of TIME value), and each bar represents 2 levels of

D. TIME Display：

Indicates the TIME displayed.

E. SPEED/RPM Display：

Indicates the value of RPM and SPEED.

F. WATT/LOAD Display：

Indicates the value of WATT and LOAD.

G. Message Display：

Indicates that the message displayed.

Fenster 1

Fenster 2

Fenster 3

Fenster 4

Window 1

Window 2

Window 3

Window 4

Computer

H. CALORIES Display：

Indicates the value of CALORIES.

I. DISTANCE Display：

Indicates the value of DISTANCE.

J. PULSE Display：

Indicates the value of PULSE.

● Operating Ranges

Display Exercise Data：

TIME

Display range 0:00~99:99 ; Setting range 0:00~99:00.

DISTANCE

Display range 0.00~99.99 ; Setting range 0.00~99.90km.

CALORIES

Display range 0~9999 ; Setting range 0~9990.

PULSE

Display range P-30~230 ; Setting range 0-30~230.

WATT

Display range 0~999 ; Setting range 10~350.

SPEED

0.0~99.9km.

RPM

0~999.

● Things You Should Know Before Exercising

A. The values calculated or measured by the computer are for exercise purpose only, not for

medical purpose.

B. Please note that only 1 value of TIME or DISTANCE can be adjusted. Both adjustments do

not exist at the same time. For example, the value of DISTANCE is “0” while of TIME is

adjusted to be any number except “00:00”.

Fenster 5

Fenster 6

Fenster 7

Window 5

Window 6

Window 7

Computer

Program Selection:

There are 19 programs with 1 Manual Program, 12 Preset Program, 4 Heart Rate Control

Program, 1 User Setting Program, 1 Watt Control Program, and 1 Pulse Recovery

Measuring.

C. Program Graph:

Each graph shown is the profile of the loading in each interval (column). With the value of

km counting up, each interval is 0.1 km that all the columns make up 2 km. With the value

of TIME counting down, each interval is the value of setup TIME divided by 20.

For example, if the time value is setup to 40 minutes, each interval will be 40 minutes

divided by 20 intervals (40/20=2). Then, each interval will be 2 minutes. The following

graphs are all the profiles in the monitor.

● Operation Instructions

A. Manual Mode:

Adjust resistance during workout manually.

Press START in main menu may start workout in manual mode.

You can also choose to into Mode function with following steps.

1. Press UP or DOWN to select workout program, choose Manual and press Mode to

enter.

Computer

2. Press UP or DOWN to preset TIME, DISTANCE, CALORIES, PULSE and press MODE

to confirm.

3. Press START/STOP keys to start workout. Press UP or DOWN to adjust load level.

4. Press START/STOP keys to pause workout. Press RESET to reverse to main menu.

B. Program Mode:

Choose a preset workout program.

1. Press UP or DOWN to select workout program, choose the Program and press Mode to

enter. (Total Program = 12)

2. Press UP or DOWN to preset TIME.

3. Press START/STOP key to start workout. Press UP or DOWN to adjust load level.

4. Press START/STOP key to pause workout. Press RESET to reverse to main menu.

C. User Program Mode:

Press your own workout profile.

1. Press UP or DOWN to select workout program, choose User and press Mode to enter.

2. Press UP or DOWN to set load level of each column, and press MODE to next one.

3. Hold on pressing MODE to finish or quit setting.

4. Press UP or DOWN to preset workout TIME.

5. Press START/STOP key to start workout. Press UP or DOWN to adjust load level.

6. Press START/STOP key to pause workout. Press RESET to reverse to main menu.

Computer

D. H.R.C. Mode:

1. Press UP or DOWN to select workout program, choose H.R.C. and press Mode to enter.

2. Press UP or DOWN to preset user age.

3. Press UP or DOWN to select 55%, 75%, 90%, or TAG (TARGET H.R.) (default:100).

4. Press UP or DOWN to preset workout TIME.

5. Press START/STOP key to start or stop workout. Press RESET to reverse to main

menu.

E. WATT Mode:

1. Preset UP or DOWN to preset WATT and press MODE to confirm.

2. Press UP or DOWN to preset WATT target. (default:120)

3. Press UP or DOWN to preset TIME.

4. Press START/STOP key to start workout. Press UP or DOWN to adjust Watt level.

5. Press START/STOP key to pause workout. Press RESET to reverse to main menu.

Computer

F. Recovery:

Monitor heart rate recovery status.

1. User must be holding the handgrip. When the pulse value is displayed on the computer,

press on the RECOVERY key.

2. TIME shows “0:60” (seconds) and count down.

3. Computer will show F1 to F6 after count down to 0 to test heart rate recovery status.

※ Please see the F level chart below to determine the recovery level.

1.0

OUTSTANDING

1.0 ＜ F ＜ 2.0

EXCELLENT

2.0 ＜ F ＜ 2.9

GOOD

3.0 ＜ F ＜ 3.9

FAIR

4.0 ＜ F ＜ 5.9

BELOW AVERAGE

6.0

POOR

G. Smart Phone/Tablet PC USB Charger:

Please connect your USB smart phone/tablet PC charger to the USB connector at the side

of the computer. You can charge your smart phone/ tablet PC on the smart phone/tablet PC

dock. The smart phone/tablet PC dock on the computer is for most of smart phones.

Page is loading ...

Orbit OBEI50A Owner's manual

Brand: Orbit

Model: OBEI50A

Category: Fitness, gymnastics & weight training

Type: Owner's manual

Download PDF

report

Orbit OBEI50A Owner's manual

Orbit OBEI50A Owner's manual

Related papers

Other documents