Accessory Power SLR Wireless RF Remote User manual

  • Hello! I am an AI chatbot trained to assist you with the Accessory Power SLR Wireless RF Remote User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTRUCTION MANUAL
SLR WIRELESS RF
Remote
Product Diagram
Whats in the box?
Thank you for purchasing this Accessory Power SLR Wireless RF Remote. This unit
allows you to trigger your camera shutter and execute other camera functions wire-
lessly. This remote utilizes 16-channel RF signal transmission for a reliable and rapid
response every time. Use this wireless remote for single exposure, bulb mode, delayed
shooting, and continuous shooting.
a - Wireless RF remote
b - Receiver
c - CR2 battery
1 - Remote shutter release
2 - Mode Switch
3 - Remote LED
4 - Receiver power button
5 - Receiver shutter release
6 - Receiver LED
7 - Connection pin
8 - Hot shoe mount
9 - RF channel switches
10 - CR2 battery compartment
a
1
2
3
4
5
6
7
9
10
8
b
c
Remote Functions
Inserting the CR2 battery
Insert the included (c) CR2 battery into the (10) CR2 battery compartment on the
(b) receiver.
Connecting the Receiver to your Camera
First, mount the (b) receiver onto the top of your camera with the (8) Hot-shoe
mount.
Next, insert the (7) Connection pin into the remote port on your camera. Please
refer to your cameras user’s manual if you are having trouble.
Press the (4) receiver power button and you will see the (6) receiver LED glow red.
Turn your Cameras power ‘ON’.
Single and Continuous Shooting
Please make sure the (2)mode switch on the (a)wireless RF remote is switched to
B. Press the (1) remote shutter release down half way to auto-focus. Once
focused, you can press the button down completely to take a single shot, or if you
have your camera set to continuous shooting, it will begin the series of shots.
Bulb Mode
Please make sure that your camera is set to Bulb Mode (Long Exposure). Please
make sure the (2) mode switch on the (a) wireless RF remote is switched to B.
Press down the (1) remote shutter release and hold it until the (3) remote LED turns
o . The red (6) receiver LED will turn on permanently to indicate that Bulb Mode is
active. To turn Bulb Mode o , just hold down the (1) remote shutter release again.
Operating Instructions:
Troubleshooting
Delayed Shooting
Please make sure the (2) mode switch on the (a) wireless RF remote is switched to
Press the (1) remote shutter release down fully and hold. The camera will begin
to focus and there will be 3 seconds until the shutter of the camera is triggered.
Using the Receiver like a Corded Remote
The (b) receiver can function like a corded remote, even without the (c) CR2 bat-
tery. To trigger the shutter, just press down the (5) receiver shutter release. The
auto-focus control is similar to using the (a) wireless RF remote. Press down half-
way to focus, and fully to activate the cameras shutter. For Bulb Mode shooting,
simply make sure that you camera is set to Bulb Mode, and hold the (5) receiver
shutter release down for as long as you need.
My model of camera is listed as compatible, but I cant  gure out how to con-
nect the (b) receiver to my camera.
- Please consult your cameras user manual. There are layouts and diagrams
of every port on your camera. If you do not have the manual, please go to the
manufacturers website and download the PDF User’s Manual. Most Users
Manuals are readily available for download.
The (b) receiver does not power on (red LED does not glow) when pressing the
receiver power button.
- Please make sure your have inserted the (c) CR2 battery correctly. Try replacing
the (c) CR2 battery if the problem does not improve.
Remote Functions (cont’d)
.
After following the setup instructions carefully, I can’t get my camera to re-
spond when I trigger the (a) wireless RF remote.
- Please make sure you have properly connected the (7) connection pin into the
remote port on your camera. Try re-inserting.
- Please make sure the channels on the back of the (b) receiver and remote are set
to match.
- Your camera may have to be set into a Remote Shooting mode in the settings
menu. Please consult your Users Manual.
- Please make sure that you are fully pressing down the shutter release button so
that you see the LED glow red.
Troubleshooting (cont’d)
- Keep in a safe place free from dust, liquid and extreme temperatures
- Only use this device with the recommended power sources
- Keep out of reach of small children
- When not in use, please disconnect batteries or power sources
Cautions
Product Speci cations
Frequency: 433MHz
Transmission Range: 300 feet
Battery: Wireless RF Remote– 23A ; Receiver – CR2
Weight: 3 ounces
©
2010 ACCESSORY POWER
All trademarks and brand names are the property of their owners
1/7