Owner’s
Manual
CD-42
IMPORTANT
Read and follow all
Safety Precautions
and Instructions
Before Operating this
Equipment.
Made In CHINA
1602 CORPORATE DRIVE , PO BOX 67, WARRENSBURG, MISSOURI 64093
PH 660. 747. 8183 FAX 660. 747. 8650
swisherinc.com
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945
CULTIVATING DISC
14674 REV. 07-344
LIMITED WARRANTY
The manufacturer’s warranty to the original consumer purchaser is: This product is free
from defects in materials and workmanship for a period of One (1) year from the date of
purchase by the original consumer purchaser. We will repair or replace, at our discretion,
parts found to be defective due to materials or workmanship. This warranty is subject to the
following limitations and exclusions:
1) Commercial Use This product is not intended for commercial use and
carries no commercial warranty.
In the event you have a claim under this warranty, you must return the product to an
authorized service dealer. All transportation charges, damage, or loss incurred during
transportation of parts submitted for replacement or repair under this warranty shall be borne
by the purchaser. Should you have any questions concerning this warranty, please contact
us toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the
name of the authorized Swisher dealer from whom you purchased the mower will be needed
before any warranty claim can be processed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME
PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not
allow the limitation of consequential damages or limitations on how long an implied warranty
may last, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights and you may have other rights, which vary from state-to-state. This is
a limited warranty as defined by the Magnuson-Moss Act of 1975.
2) Limitation This warranty applies only to products which have been
properly assembled, adjusted, and operated in accordance
with the instructions contained within this manual. This
warranty does not apply to any product of Swisher Mower
Co., Inc., that has been subject to alteration, misuse, abuse,
improper assembly or installation, shipping damage, or to
normal wear of the product.
3) Exclusions Excluded from this warranty are normal wear, normal
adjustments, and normal maintenance.
2
2
3
ASSEMBLY INSTRUCTIONS FOR ATV DISC
Step 1: Assemble the two disc gang assemblies as shown in diagram
Note: The diagram shows each item number as it is assembled
onto the Square Axle Weldment. Tighten Lock Nut so all disc's
are tight on Square Axle Weldment.
4
Step 2: Assemble the Hitch Tongue to the Frame using the Hex Bolts, Big
Flat Washers and Lock Nuts. Note: Do not over tighten Hex Bolts
and Lock Nuts, the Hitch Tongue should rotate up and down freely.
Install the Wheel Bracket into the frame as shown in dia
gram.
Note: Check the direction of angle iron on the wheel bracket as
shown in diagram.
5
Step 3: Install the two Disc Gang assemblies to the frame using the U bolts
and Lock Nuts as shown in diagram.
Note: Install the two Disc Gang assemblies in the opposite direction,
if they are installed incorrectly the disc will not function properly.
Note: Install the two Disc Gang Assemblies onto
the Frame in the opposite direction.
6
Step 4: Install the Mechanical Screw Jack onto the frame as shown in
the diagram using the Hex bolts and Lock Nuts.
Note: Do not over tighten these two bolts and Lock Nuts.
Mechanical Jack
Step 5: Install Adjustable Rod to the Hitch Tongue and the Frame using
the Hex Bolts and Lock Nuts as Shown.
Install the Tires onto the Wheel bracket using the Flat Washers,
Hex Bolts and Lock Nuts as shown.
Step 6: There maybe some adjusting of the Hitch Tongue for the height
of towing vehicle, this function can be performed by rotating handle
on Adjusting Rod.
Rotating the handle on the Mechani
cal Screw Jack will raise the
tires up down.
Adjust the height of
the Hitch Tongue by
rotating this handle.
Adjust the tires up or
down by rotating this handle.
This illustration shows the
position where the handle
be when the disc is in use.
Exploded Parts Drawing
Parts List
Item No Prt No Qty Prt No Item No Description Qty
1 14546 1 14555 21 1
2 13767 3 15304 22 2
3 13671 29 14681 23 1
4 14547 1 024900 24 2
5 14548 1 14556 25 2
6 14787 3 14557 26 4
7 15302 6 14558 27 8
8 14680 4 14559 28 4
9 14306 4 15305 29 Carriage Bolt M12×35 16
10 14849 7 14560 30 2
11 14784 2 14561 31 4
12 14550 1 14562 32 10
13 12124 1 14563 33 1
14 14551 1 14786 34 6
15 12190 1 15306 35 2
16 15303 1 14564 36 2
17 14552 1 11994 37 2
18 14553 1 15307 38 2
19 13670 1 15308 39 1
20 14554 1
Flat Washer Ø24
Hex Bolt M16×80
Flat Washer Ø20
Hex Bolt M5×25
Tire
Nylock Nut M5
Square Axle Weldment
Long Sleeve
Disc
Wheel Bracket
Hex Bolt M12×60
Frame
Bearing
Thick Flat Washer Ø12
Threaded Rod
Nylock Nut M24
Disc Pressure Plate
Disc Support Plate
Short Sleeve
Bearing Base Assy'
Nylock Nut M6
Big Flat Washer Ø12
Outside Sleeve
Inside Sleeve
Handle Grip
Hex Bolt M6×30
Handle
U style Bolt
Nylock Nut M16
End cap
Flat Washer Ø12
Hitch Tongue
Adjustable Rod
Hex Bolt M16×90
Big Flat Washer Ø16
Description
2" Coupling
Hex Bolt M12×80
Hex Lock Nut M12
www.swisherinc.com
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INORMATION AVAILABLE:
* PRODUCT – ________________
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER WITH PAINT CODE
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE
P.O. BOX 67
WARRENSBURG, MO 64093
ATV & LAWN ACCESSORIES
Owner’s
Manual
IMPORTANT
Read and follow all
Safety Precautions
and Instructions
Before Operating this
Equipment.
CD-42
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
