Miller AUTO ARC 255 Owner's manual

OWNER’S

MANUAL

December 1997 Form: OM-157 066J

For Technical Support, Contact:

Milweld Inc., National Distributor

P.O. Box 338, Hortonville, WI 54944-0338

Tel 920-779-0916 Fax 920-779-0924

auto_arc 6/95 − ST-157 072-A PRINTED IN USA

Auto Arc

Model 255

Wire Welder

Rated Welding Output

Amperage

Range DC

Maximum

Open-Circuit

Amperes Input at Rated Load

Output, 50 or 60 Hz, Single-Phase

Rated Welding Output

Range DC

Open Circuit

Voltage DC

200 V 230 V KVA KW

200 A @ 28 Volts DC, 60%

Duty Cycle

250 A @ 28 Volts DC, 40%

Duty Cycle

40 − 250 42

1.1*

1.3*

9.5

0.31*

8.3

0.18*

Wire Type And Diameter

Solid Steel /

Stainless Steel

Flux Cored /

Aluminum

Wire Feed Speed Range Overall Dimensions Weight

.023 − .045 in

(0.6 − 1.2 mm)

.030 − .035 in

(0.8 − 0.9 mm) And

3/64 in (1.2 mm) Alu

90 − 1030 IPM (2.9 − 26.2 m/min)

Length: 37 in (940 mm)

Width: 19 in (483 mm)

Height: 32 in (889 mm)

225 lb

(102 kg)

*While idling

OM-157 066 Page 1

SECTION 1 − SAFETY PRECAUTIONS FOR ARC WELDING

safety_som1 4/95

OM-157 066G − 3/97

1-1. Symbol Usage

Means Warning! Watch Out! There are possible hazards with this

procedure! The possible hazards are shown in the adjoining symbols.

This group of symbols means Warning! Watch Out! possible ELECTRIC SHOCK, MOVING PARTS,

and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to

avoid the hazards.

Y Marks a special safety message.

. Means NOTE; not safety related.

1-2. Arc Welding Hazards

WARNING

The symbols shown below are used throughout this manual to call attention to and identify possible

hazards. When you see the symbol, watch out, and follow the related instructions to avoid the hazard. The

safety information given below is only a summary of the more complete safety information found in the

Safety Standards listed in Section 1-4. Read and follow all Safety Standards.

Only qualified persons should install, operate, maintain, and repair this unit.

During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or

automatic wire welding, the wire, wire reel, drive roll

housing, and all metal parts touching the welding

wire are electrically live. Incorrectly installed or

improperly grounded equipment is a hazard.

1. Do not touch live electrical parts.

2. Wear dry, hole-free insulating gloves and body protection.

3. Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the

work or ground.

4. Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according

to OSHA 29 CFR 1910.147 (see Safety Standards).

5. Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

6. Always verify the supply ground − check and be sure that input

power cord ground wire is properly connected to ground terminal

in disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

7. When making input connections, attach proper grounding

conductor first − double-check connections.

8. Frequently inspect input power cord for damage or bare wiring −

replace cord immediately if damaged − bare wiring can kill.

9. Turn off all equipment when not in use.

10. Do not use worn, damaged, undersized, or poorly spliced cables.

11. Do not drape cables over your body.

12. If earth grounding of the workpiece is required, ground it directly

with a separate cable − do not use work clamp or work cable.

13. Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

14. Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

15. Wear a safety harness if working above floor level.

16. Keep all panels and covers securely in place.

17. Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

ARC RAYS can burn eyes and skin;

NOISE can damage hearing; FLYING

SLAG OR SPARKS can injure eyes.

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Noise from some

processes can damage hearing. Chipping, grinding,

and welds cooling throw off pieces of metal or slag.

NOISE

1. Use approved ear plugs or ear muffs if noise level is high.

ARC RAYS

2. Wear a welding helmet fitted with a proper shade of filter to protect

your face and eyes when welding or watching (see ANSI Z49.1

and Z87.1 listed in Safety Standards).

3. Wear approved safety glasses with side shields.

4. Use protective screens or barriers to protect others from flash

and glare; warn others not to watch the arc.

5. Wear protective clothing made from durable, flame-resistant

material (wool and leather) and foot protection.

FUMES AND GASES can be

hazardous to your health.

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

1. Keep your head out of the fumes. Do not breathe the fumes.

2. If inside, ventilate the area and/or use exhaust at the arc to

remove welding fumes and gases.

3. If ventilation is poor, use an approved air-supplied respirator.

4. Read the Material Safety Data Sheets (MSDSs) and the

manufacturer’s instruction for metals, consumables, coatings,

cleaners, and degreasers.

5. Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained

watchperson nearby. Welding fumes and gases can displace air

and lower the oxygen level causing injury or death. Be sure the

breathing air is safe.

6. Do not weld in locations near degreasing, cleaning, or spraying

operations. The heat and rays of the arc can react with vapors to

form highly toxic and irritating gases.

7. Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the

weld area, the area is well ventilated, and if necessary, while

wearing an air-supplied respirator. The coatings and any metals

containing these elements can give off toxic fumes if welded.

OM-157 066 Page 2

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

1. Protect compressed gas cylinders from excessive heat,

mechanical shocks, slag, open flames, sparks, and arcs.

2. Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

3. Keep cylinders away from any welding or other electrical circuits.

4. Never drape a welding torch over a gas cylinder.

5. Never allow a welding electrode to touch any cylinder.

6. Never weld on a pressurized cylinder − explosion will result.

7. Use only correct shielding gas cylinders, regulators, hoses, and

fittings designed for the specific application; maintain them and

associated parts in good condition.

8. Turn face away from valve outlet when opening cylinder valve.

9. Keep protective cap in place over valve except when cylinder is in

use or connected for use.

10. Read and follow instructions on compressed gas cylinders,

associated equipment, and CGA publication P-1 listed in Safety

Standards.

WELDING can cause fire or

explosion.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks,

hot workpiece, and hot equipment can cause fires

and burns. Accidental contact of electrode to metal

objects can cause sparks, explosion, overheating,

or fire. Check and be sure the area is safe before

doing any welding.

1. Protect yourself and others from flying sparks and hot metal.

2. Do not weld where flying sparks can strike flammable material.

3. Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

4. Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

5. Watch for fire, and keep a fire extinguisher nearby.

6. Be aware that welding on a ceiling, floor, bulkhead, or partition

can cause fire on the hidden side.

7. Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

8. Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock and fire hazards.

9. Do not use welder to thaw frozen pipes.

10. Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

11. Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

12. Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

1-3. Additional Installation, Operation, And Maintenance Hazards

FIRE OR EXPLOSION can result from

placing unit on, over, or near

combustible surfaces.

1. Do not locate unit on, over, or near combustible

surfaces.

2. Do not install unit near flammables.

FALLING EQUIPMENT can cause

serious personal injury and equipment

damage.

1. Use lifting eye to lift unit only, NOT running gear,

gas cylinders, or any other accessories.

2. Use equipment of adequate capacity to lift unit.

3. If using lift forks to move unit, be sure forks are long

enough to extend beyond opposite side of unit.

HOT PARTS can cause severe burns.

1. Do not touch hot parts bare handed.

2. Allow cooling period before working on gun or

torch.

MOVING PARTS can cause injury.

1. Keep away from moving parts such as fans.

2. Keep all doors, panels, covers, and guards closed

and securely in place.

MAGNETIC FIELDS FROM HIGH

CURRENTS can affect pacemaker

operation.

1. Pacemaker wearers keep away.

2. Wearers should consult their doctor before going

near arc welding, gouging, or spot welding

operations.

MOVING PARTS can cause injury.

1. Keep away from moving parts.

2. Keep away from pinch points such as drive rolls.

FLYING PIECES OF METAL or DIRT can

injure eyes.

1. Wear safety glasses with side shields or face

shield.

WELDING WIRE can cause puncture

wounds.

1. Do not press gun trigger until instructed to do so.

2. Do not point gun toward any part of the body, other

people, or any metal when threading welding wire.

HIGH-FREQUENCY RADIATION can

interfere with radio navigation, safety

services, computers, and

communications equipment.

1. Have only qualified persons familiar with electronic

equipment perform this installation.

2. The user is responsible for having a qualified

electrician promptly correct any interference

problem resulting from the installation.

3. If notified by the FCC about interference, stop using

the equipment at once.

4. Have the installation regularly checked and

maintained.

5. Keep high-frequency source doors and panels

tightly shut, keep spark gaps at correct setting, and

use grounding and shielding to minimize the

possibility of interference.

OM-157 066 Page 3

OVERUSE can cause OVERHEATED

EQUIPMENT.

1. Allow cooling period.

2. Reduce current or reduce duty cycle before

starting to weld again.

3. Follow rated duty cycle.

STATIC ELECTRICITY can damage

parts on circuit boards.

1. Put on grounded wrist strap BEFORE handling

boards or parts.

2. Use proper static-proof bags and boxes to store,

move, or ship PC boards.

SIGNIFICANT DC VOLTAGE exists after

removal of input power on inverters.

1. Turn Off inverter, disconnect input power, and

discharge input capacitors according to

instructions in Maintenance Section before

touching any parts.

BUILDUP OF SHIELDING GAS can harm

health or kill.

1. Shut off shielding gas supply when not in use.

1-4. Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American

Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

Safety and Health Standards, OSHA 29 CFR 1910, from

Superintendent of Documents, U.S. Government Printing Office,

Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for Welding and

Cutting of Containers That Have Held Hazardous Substances,

American Welding Society Standard AWS F4.1, from American

Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

National Electrical Code, NFPA Standard 70, from National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet

P-1, from Compressed Gas Association, 1235 Jefferson Davis

Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from

Canadian Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices For Occupation And Educational Eye And Face

Protection, ANSI Standard Z87.1, from American National Standards

Institute, 1430 Broadway, New York, NY 10018.

Cutting And Welding Processes, NFPA Standard 51B, from National

Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

1-5. EMF Information

Considerations About Welding And The Effects Of Low Frequency

Electric And Magnetic Fields

The following is a quotation from the General Conclusions Section of

the U.S. Congress, Office of Technology Assessment, Biological

Effects of Power Frequency Electric & Magnetic Fields − Background

Paper, OTA-BP-E-53 (Washington, DC: U.S. Government Printing

Office, May 1989): “. . . there is now a very large volume of scientific

findings based on experiments at the cellular level and from studies

with animals and people which clearly establish that low frequency

magnetic fields can interact with, and produce changes in, biological

systems. While most of this work is of very high quality, the results are

complex. Current scientific understanding does not yet allow us to

interpret the evidence in a single coherent framework. Even more

frustrating, it does not yet allow us to draw definite conclusions about

questions of possible risk or to offer clear science-based advice on

strategies to minimize or avoid potential risks.”

To reduce magnetic fields in the workplace, use the following

procedures:

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around the body.

4. Keep welding power source and cables as far away as

practical.

5. Connect work clamp to workpiece as close to the weld as

possible.

About Pacemakers:

The above procedures are also recommended for pacemaker

wearers. Consult your doctor for complete information.

OM-157 066 Page 4

SECTION 2 − INSTALLATION

2-1. Installing Work Clamp

1 Work Cable

2 Boot

Slide boot onto work cable. Route

cable out front panel opening from

inside.

3 Negative (−) Output Terminal

Connect cable to terminal and

cover connection with boot.

4 Hardware

5 Work Clamp

Route cable through clamp handle

and secure as shown.

Close door.

ST-800 918-B

1/2, 3/4 in

Tools Needed:

2-2. Installing Gas Supply

ST-154 623-A / Ref. ST-109 492

Chain gas cylinder to running gear,

wall, or other stationary support so

cylinder cannot fall and break off

valve.

1 Regulator/Flow Gauge

Install so face is vertical.

2 Gas Hose Connection

Fitting has 5/8-18 right-hand

threads.

3 Flow Adjust

Typical flow rate is 20 cfh (cubic feet

per hour). Check wire manufactur-

er’s recommended flow rate. This

flow gauge can be adjusted be-

tween 5 and 25 cfh.

4CO

Adapter

Customer Supplied

5 O-Ring

Install adapter with O-ring between

regulator/flow gauge and CO

cylinder.

5/8, 1-1/8 in

Tools Needed:

Gas

4 5

Argon Gas

OM-157 066 Page 5

2-3. Installing Welding Gun

Ref. ST-801 677

1 Drive Assembly

2 Gun Securing Knob

3 Gun End

Loosen securing knob. Insert gun

end through opening until it bottoms

against drive assembly. Tighten

nut.

4 Gun Trigger Plug

Insert plug into receptacle, and

tighten threaded collar.

Close door.

2-4. Installing Wire Spool And Adjusting Hub Tension

ST-072 573-B

When a slight force is needed to turn spool, tension is set.

15/16 in

Use compression spring with

8 in (200 mm) spools.

Tools Needed:

OM-157 066 Page 6

2-5. Setting Gun Polarity

1 Polarity Changeover Label

(Located Near Drive

Assembly)

Always read and follow manufac-

ture’s recommended polarity.

Shown As Shipped − Set For Electrode

Positive (DCEP) For Solid Steel Or

Aluminum Wires (GMAW Process).

Wire Drive Assembly Lead

To Positive (+) Output Terminal

Work Clamp Lead To

Negative (−) Output Terminal

GUN POLARITY

CHANGEOVER CONNECTIONS

Reverse Lead Connections − For Electrode

Negative (DCEN) For Flux Cored Wires

(FCAW Process). Drive Assembly

Becomes Negative

S-144 449-D

3/4, 11/16 in

Tools Needed:

OM-157 066 Page 7

2-6. Positioning Jumper Links

Ref. ST-800 922-B

Check input voltage available at

site.

1 Jumper Links Access Door

Open door.

2 Jumper Link Label

3 Input Voltage Jumper Link

Move jumper link to match input

voltage.

Close and secure access door.

200 VOLTS

230 VOLTS

S-153 980

3/8 in

Tools Needed:

2-7. Electrical Service Guide

Input Voltage

200 230

Input Amperes At Rated Output

46 40

Max Recommended Standard Fuse Or Circuit Breaker Rating In

Amperes

70 60

Min Input Conductor Size In AWG/Kcmil

8 8

Max Recommended Input Conductor Length In Feet (Meters)

89 (27) 117 (36)

Min Grounding Conductor Size In AWG/Kcmil

8 8

Reference: 1996 National Electrical Code (NEC). S-0092J

OM-157 066 Page 8

2-8. Selecting A Location And Connecting Input Power

1 Rating Label

Supply correct input power.

2 Plug

3 Receptacle (Not Supplied)

Connect plug to receptacle.

4 Line Disconnect Device

See Section 2-7.

Y Special installation may be

required where gasoline or

volatile liquids are present −

see NEC Article 511 or CEC

Section 20.

ST-800 923-A

L1L2

230 VAC, 1

18 in (457 mm) of

space for airflow

Y Do not move or operate unit

where it could tip.

Y Always connect

grounding conductor first.

= GND/PE

OM-157 066 Page 9

2-9. Threading Welding Wire

1 Wire Spool

2 Welding Wire

3 Inlet Wire Guide

4 Pressure Adjustment Knob

5 Drive Roll

6 Outlet Wire Guide

7 Gun Conduit Cable

Lay gun cable out straight.

35 621

Ref. ST-801 677 / S-0627-A

6 in

(150 mm)

4 in

(102 mm)

Tighten

WOOD

Open pressure assembly. Pull and hold wire; cut off end. Push wire thru guides into gun;

continue to hold wire.

Close and tighten pressure

assembly, and let go of wire.

Remove gun nozzle and contact tip. Turn On.

Press gun trigger until wire

comes out of gun. Reinstall

contact tip and nozzle.

Feed wire to check drive roll pressure.

Tighten knob enough to prevent slipping.

Cut off wire. Close

and latch door.

Tools Needed:

OM-157 066 Page 10

SECTION 3 − OPERATION

3-1. Front Panel Controls

Ref. ST-171 639-C / Ref. ST-174 843-A

Controls For Standard Units

1 Wire Speed Control

The scale around the control is

percent, not wire feed speed.

2 Voltage Switch

Use control and Voltage Range Se-

lector (see Section 3-2) to set arc

voltage. Step 6 of Low range and

Step 1 of High range overlap.

3 Pilot Light

4 Power Switch

3-2. Center Baffle Controls

Ref. ST-800 919 / S-171 601

1 Wire Mode Switch

For better control of wire speed use

the Low position when wire speed is

between 90 and 670 ipm. Use the

Full position when wire speed is be-

tween 150 ipm and 1030 ipm.

2 Voltage Range Selector

Place switch in desired position.

DO NOT SWITCH

UNDER LOAD

CB1

PRESS TO RESET

LOW

FULL

LOW

HIGH

WIRE

MODE

VOLTAGE

RANGE

OM-157 066 Page 11

6 Minutes Welding 4 Minutes Resting

3-3. Duty Cycle And Overheating

Duty Cycle is percentage of 10 min-

utes that unit can weld at rated load

without overheating.

If unit overheats, thermostat(s)

opens, output stops, and cooling

fan runs. Wait fifteen minutes for

unit to cool. Reduce amperage or

voltage, or duty cycle before

welding.

Y Exceeding duty cycle can

damage unit and void

warranty.

Overheating

A or V

Reduce Duty Cycle

Minutes

duty1 4/95 − SB-150 215

60% Duty Cycle At 200 Amperes

OM-157 066 Page 12

SECTION 4 − MAINTENANCE & TROUBLESHOOTING

4-1. Routine Maintenance

Y Disconnect power

before maintaining.

. Maintain more often

during severe conditions.

3 Months

Replace

Damaged Or

Unreadable

Labels

Clean And

Tighten

Weld

Terminals

Repair Or

Replace

Cracked

Cables And

Cords

6 Months

Blow Out Or

Vacuum Inside

4-2. Circuit Breaker CB1

Ref. ST-801 677

1 Circuit Breaker CB1

If CB1 opens, wire feeding stops.

2 Welding Gun

Check gun liner for blockage or

kinks.

3 Wire Drive Assembly

Check for jammed wire, binding

drive gear or misaligned drive rolls.

Allow cooling period and reset

breaker. Close door.

OM-157 066 Page 13

4-3. Fuses F1 And F2

Ref. ST-800 928-B

Y Turn Off unit, and disconnect

input power.

1 Fuse F1 (See Parts List For

Rating)

F1 protects the 115 volts ac winding

of transformer T1. If F1 opens, all

weld output stops and pilot light PL1

goes out.

2 Fuse F2 (See Parts List For

Rating)

F2 protects the 24 volts ac winding

of transformer T1. If F2 opens, all

weld output stops.

3/8 in

Tools Needed:

OM-157 066 Page 14

4-4. Changing Drive Roll And Wire Inlet Guide

ST-150 227-C

1 Securing Screw

2 Inlet Wire Guide

Loosen screw. Slide tip as close to

drive rolls as possible without touch-

ing. Tighten screw.

3 Anti-Wear Guide

Install guide as shown.

4 Drive Roll

Install correct drive roll for wire size

and type.

5 Drive Roll Securing Nut

Turn nut one click to secure drive

roll.

5/64 in

7/16 in

Tools Needed:

4-5. Aligning Drive Rolls And Wire Guide

Y Turn Off unit.

View is from top of drive rolls look-

ing down with pressure assembly

open.

1 Drive Roll Securing Nut

2 Drive Roll

3 Wire Guide

4 Welding Wire

5 Drive Gear

Insert screwdriver, and turn screw

in or out until drive roll groove lines

up with wire guide.

Close pressure assembly.

Ref. ST-800 412-A

Correct Incorrect

Tools Needed:

OM-157 066 Page 15

4-6. Troubleshooting

Welding Trouble Remedy

No weld output; wire does not feed. Secure power cord plug in receptacle (see Section 2-8).

Reset circuit breaker CB1 (see Section 4-2).

Replace fuse F1 and/or F2 (see Section 4-3).

Replace building line fuse or reset circuit breaker if open (see Section 2-8).

Secure gun trigger plug in receptacle or repair leads, or replace trigger switch (see Section 2-3).

Thermostat TP1 open (overheating). Allow fan to run; the thermostat will close when the unit has cooled

(see Section 3-3).

No weld output; wire feeds. Connect work clamp to get good metal to metal contact.

Replace contact tip (see Gun Owner’s Manual).

Low weld output. Connect unit to proper input voltage or check for low line voltage (see Section 2-8).

Wire Drive/Gun Trouble Remedy

Electrode wire feeding stops during

welding.

Straighten gun cable and/or replace damaged parts (see Gun Owner’s Manual).

Adjust drive roll pressure (see Section 2-9).

Readjust hub tension (see Section 2-4).

Replace contact tip if blocked (see Gun Owner’s Manual).

Clean or replace wire inlet guide or liner if dirty or plugged (see Gun Owner’s Manual).

Replace drive rolls if worn or slipping (see Section 4-4).

Secure gun trigger plug in receptacle or repair leads, or replace trigger switch (see Section 2-3).

Check and replace F1 and/or F2 (see Section 4-3).

Check and clear any restrictions at drive assembly and liner (see Gun Owner’s Manual).

Have nearest Factory Authorized Service Agent check drive motor.

OM-157 066 Page 16

SECTION 5 − ELECTRICAL DIAGRAM

SB-173 544-D

For Primary Circuit Diagram Portion, refer

to Circuit Diagram located inside the wrapper

of the welding power source.

Figure 5-1. Circuit Diagram For Welding Power Source

OM-157 066 Page 17

SECTION 6 − PARTS LIST

FIG 6−2 − 2

ST-800 930-C

. Hardware is common and

not available unless listed.

Figure 6-1. Main Assembly

NOTE: All items indented by a dot(s) are included with the item listed directly above.

Description

Part

No.

Item

No.

Part

No.

Item

No. Description

Part

No.

Item

No. Description

1 146 168 Enclosure Panel

083 526 Housing Rcpt & Sockets

2 Fig 6-2 Baffle w/Cmpts

3 171 658 Transformer

4 602 250 Washer, flat

5 186 758 Wheel

6 171 213 Stabilizer

7 Rear Panel w/Cmpts

148 808 · Fan Motor

150 783 · Fan Blade

049 399 · Speed Nut

116 996 · Gas Valve

605 227 · Nylon Nut, .750

146 524 · Hose

149 332 · Hose Clamp

152 742 · Rectifier

048 420 · · Capacitor

037 957 · · Diode, RP

037 956 · · Diode, SP

605 886 · · Washer, .750

605 884 · · Half Nut, .750-16

171 600 · · Thermostat, NC

026 947 · · Stand-Off

152 862 · · Grommet

009 970 · Rectifier Bracket

143 810 · Rear Panel

169 654 · Tank Bracket Support

044 426 · Cable Clamp

8 602 387 Cylinder Chain

9 146 165 Side Panel, LH

10 089 899 Latch

11 146 167 Side Panel

12 134 464 Warning Label

13 +170 513 Wrapper

14 047 721 Cord Set

15 146 161 Base

16 135 390 Axle

17 121 614 · Retaining Ring

18 091 685 Resistor

605 741 Clip

19 602 213 Lock Washer

20 008 999 Caster

21 601 871 Jam Nut

22 Front Panel w/Cmpts

160 775 · Light

035 897 · Potentiometer

097 924 · Knob

048 282 · Receptacle w/Sockets

128 755 · Switch, DPST

153 197 · Selector Switch

148 956 · Switch Handle

175 060 · Front Panel

155 418 · Front Control Panel

171 639 · Control Plate

174 842 · Nameplate

144 127 · Cover, module opening

057 357 · Bushing, 1.125mtg

143 974 · Handle

23 See Gun Owner’s Manual

183 581 Gas Hose

600 318 Weld Cable

130 750 Ground Clamp

173 374 Regulator/Flowmeter

+When ordering a component originally

displaying a precautionary label, the label

should also be ordered.

Be sure to provide Model and Serial Number

when ordering replacement parts.

OM-157 066 Page 18

ST-800 931-C

Fig.6−3 − 27

Figure 6-2. Baffle w/Components (Fig 6-1 Item 3)

NOTE: All items indented by a dot(s) are included with the item listed directly above.

Description

Part

No.

Item

No.

Part

No.

Item

No. Description

Part

No.

Item

No. Description

1 058 427 Retaining Ring

2 085 980 Nut

3 605 941 Flat Washer

4 186 437 Spring, .845 OD

5 057 971 Keyed Washer

6 057 745 Spring, 2.430 OD

7 186 435 Hub, spool

8 058 628 Brake Washer

9 177 307 Support Reel

10 174 812 Baffle

11 083 147 Grommet

12 082 902 Strip, mtg center

13 092 186 Strip, mtg LH & RH

14 156 517 Capacitor

15 186 355 Contactor

114 786 Link

16 134 201 PC Card Stand-Off

17 173 002 Motor Speed Control Card

18 *012 658 · Fuse, mintr gl slo-blo

2A 125V

18 *073 426 · Fuse, mintr gl slo-blo

5A 125V

165 896 Connector & Sockets

135 558 Connector & Sockets

165 745 Connector & Sockets

19 083 431 Circuit Breaker

20 011 609 Toggle Switch, SPDT

21 171 610 Selector Switch

22 153 322 Terminal Assembly, pri 2V

038 618 · Link

23 010 199 Tubing

24 039 047 Output Terminal, red

25 039 046 Output Terminal, black

128 750 Capacitor

26 071 971 Cover

27 174 861 Drive Assembly, (Fig 6-3)

28 148 956 Switch Handle

29 144 933 Access Door

30 021 469 Danger Label

♦OPTIONAL

*Recommended Spare Parts

Be sure to provide Model and Serial Number

when ordering replacement parts.

Page is loading ...

Miller AUTO ARC 255, KH557855 Owner's manual

Related papers

Other documents