September 1991 FORFORM:
Use above FORM number when ordering extra manuals.
OWNER’S MANUAL
OM-668B
No. 4B Running Gear
CR-4B Cylinder Rack
WARNING: FALLING EQUIPMENT can cause serious personal injury and equipment damage.
• Use equipment of adequate capacity to lift the unit.
• If using lift forks to handle this unit, be sure the lift forks are long enough to extend out of the opposite
side of the base.
• Do not place any part of the body under the unit while it is suspended.
IMPORTANT: The running gear wheels and front pivot support require periodic greasing.
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
12
12
10
9
8
18
17
20
21
20
23
22
24
*19
20
ST-110 932-E
*Included With Item 18
Figure 1. No. 4B Running Gear And CR-4B Cylinder Rack
Assembly Instructions (Figure 1)
1. Install front axle shaft (22) through holes in cart handle assembly (24). Install inside flat washers (20), wheels
(21), and outside flat washers (20). Secure wheels in place with supplied retaining rings (23).
2. Install front pivot support (18) onto generator base with supplied hardware (17, 9, 8), and coat bottom of pivot
support with grease.
OM-668 Page 2
3. Install cart handle assembly (24) onto pivot support (18), and secure by installing flat washer (20) and retaining
ring (19).
4. Remove and retain screws (7) from rear holes on generator base. Block cylinder rack (3) in position, and secure
using supplied 1/4-20 hardware (2,7) and retained screws.
5. Install rear axle (15) onto generator base with supplied hardware (17, 9, 8). Remove paint from ends of axle and
coat with grease. Install wheels (11) and flat washers (10), and secure in place with retaining rings (16).
Description
Quantity
Part
No.
Figure 1. No. 4B Running Gear & CR-4B
Item
No.
041 930 041 968
Model
4B CR-4
B
1 604 423 GRIP, handle 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 089 800 NUT, stl flg lkg hex .250-20 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 110 052 RACK, cylinder 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 602 389 HOOK, S blunt 1-1/2in 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 602 387 CHAIN, weldless 2/0 x 27 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 602 384 SNAP, chain 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 108 940 SCREW, cap stl hexwhd .250-20 x .750 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 601 872 SCREW, stl hex full fnsh .375-16 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 602 213 WASHER, lock stl split .375 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 133 812 WASHER, flat stl 1.062 ID x 1.500 OD 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 022 825 WHEEL w/TIRE & BRG, 8in tire w/1in. brg .750 hub (consisting of) 2. . . . . . . . . . . . . . . .
12 022 866 BEARING 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 022 619 TIRE, 400/8 4ply 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 022 886 RIM, 8 in 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
022 622 TUBE, 400/8 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 107 265 AXLE, rear running gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 145 665 RING, retaining external 1.000 shaft 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 601 965 SCREW, cap stl hexhd .375-16 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 107 332 SUPPORT, pivot front (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 121 614 RING, retaining external .750 shaft 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 602 205 WASHER, flat stl SAE .750 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 097 455 WHEEL w/TIRE & BRG, 8 in tire 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 137 295 AXLE, front running gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 121 614 RING, retaining external .750 shaft 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24 107 327 HANDLE, cart 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
-
1
-
2
Miller RUNNING GEAR NO. 4B (041930) Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller KB000000 Owner's manual
-
-
Miller KA000000 Owner's manual
-
-
-
-
Miller KF000000 Owner's manual
-
-
-
Miller KC000000 Owner's manual