GETTING STARTED
1.
Please read the safety section (page 2) in the main instructions
before proceeding further. This section
contains vital information to ensure safe positioning and use of
the TV
2.
Unpack the TV and place on a flat level surface suitable to support the weight of the TV (11.5 kg approx.). This will
require two persons to lift the TV safely.
3.
Connect the aerial into the TV Tuner connector at the rear of the TV (Fig 3).
Fig.2
Fig.4
4. Connect the mains power lead to the mains socket at the rear left side of the TV. (Fig 2
)Plug in and switch on the TV and at the mains. The LED indicator on the TV will
illuminate and show red (Fig 1).
5.
Open the battery compartment cover (Fig 4) on the reverse of the
remote control. Insert 2
x AAA 1.5V alkaline batteries in accordance with the diagram in the battery compartment.
Take care to observe the correct polarity (+/-). Refit the battery compartment cover
6.
Press the POWER button (Fig 5) to turn the TV set on. The LED indicator will turn green
and after a few seconds, the screen will activate and the first time installation menu (Fig. 6)
will appear.
7.
Use the cursor ▼/▲ buttons on the remote control to move up and down the display to
highlight desired options.
8.
The default language is “English”
if you want another language select that language using
the ►/◄ buttons and press OK.
9.
Select AUTOTUNING and press OK. Fig 7 will be displayed, using the ▲/▼ buttons select
to country of use (UK is default). Select START and press OK, the TV will now search the
entire UHF range for both digital and Analog TV stations. See Fig 8. When search is
complete the TV will display the first channel (BBC1) in DVBt mode.
Fig.5
Fig 1
Fig.7
Fig.8
WATCHING TV (basic operation)
10. To select a channel either enter the number of the channel using the number buttons
on the remote control or scroll through the channels using the channel CH+/-
buttons.
11. To view analogue TV channels press the SOURCE button to display the source
menu. Using the cursor ▲ / ▼ buttons highlight TV on the menu and press OK to
select. To view digital TV channels select DTV on this same menu.
12. To check the list of channels stored, press the CH.LIST button to display the channel
list and use the cursor ▲ / ▼ buttons to move up and down the display. To select a
channel, highlight the channel on the list and press OK to confirm.
13. Adjust the volume to the desired level using the volume
or cursor ◄ / ►buttons.
The sound can be silenced by pressing the MUTE button on the remote control and
a mute symbol will appear on the screen. Press the MUTE button a
second time to
restore the sound.
14. To switch off the TV for short periods, press the POWER
button. The TV will go into
standby mode and the LED indicator will change to red. If not using the TV for
extended periods turn off at the mains switch to conserve electricity, all settings will
be retained.
APL2668 FD
MSD106
Quick Start Guide
Fig.6
Fig.3
LCD Screen
Although the LCD screen is made with high precision technology and 99.9% or more
of the pixels are effective, dots may appear. These can be black
or bright dots (red,
green or blue) and may appear constantly on the LCD screen. This
is a structural
property of the LCD panel and is not a malfunction.
For advanced operation of this TV please consult the Instruction
Manual.
Should you have difficulty in operating this unit, please consult the Trouble Shooting Guide in
the Instruction Manual. If you suspect a fault, please contact
the Customer Help Line,
details of which can be found in the Instruction Manual.
-
1
Akura APL2668 FD Quick start guide
- Type
- Quick start guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Akura APL1668 Quick start guide
-
-
-
-
Akura ADLTDVD3233 Quick start guide
-
-
-
-