Crestron Fusion® Software SSI Model

Reference Guide

Crestron Electronics, Inc.

Original Instructions

The U.S. English version of this document is the original instructions.

All other languages are a translation of the original instructions.

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a

limited nonexclusive, nontransferable Software Development Tools License Agreement. Crestron product operating

system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement.

Mercury, Crestron Studio, Crestron Toolbox, DM, and RoomView are either trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and/or other countries. Blu-ray Disc is either a trademark or a registered

trademark of Blu-ray Disc Association (BDA) in the United States and/or other countries. Bluetooth is either a

trademark or registered trademark of Bluetooth SIG, Inc. in the United States and/or other countries. Microsoft and

Skype are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks

and names of others. Crestron is not responsible for errors in typography or photography.

©2019 Crestron Electronics, Inc.

Contents

Call Usage Reporting 4

RoomOccupied 5

DisplayPowerIsOn 6

DisplayUsage 6

OnlineStatus 6

ErrorMessage 7

SystemPowerIsOn 8

Approved Asset Types 9

SSI Programming 11

Add the Fusion Room Device Definition 12

Program the Fusion SSIDisplay Usage Module 31

Programming Procedure 31

Signal Definitions 34

Program the Fusion SSI Device Usage Module 35

Programming Procedure 35

Signal Definitions 38

Program the Fusion SSI Equipment Status Module 39

Programming Procedure 39

Signal Definitions 42

Reference Guide — 7898E Contents • i

Program the Fusion SSI Text Message Send and Receive Module 51

Programming Procedure 51

Signal Definitions 53

Program the Fusion SSI Scheduling Awareness Module 55

Programming Procedure 55

Signal Definitions 56

Crestron Fusion Request/Response XML Streams 61

Basics 61

Data Fields 62

Schedule Requests 63

Room List Request 68

Room List Response 69

Room Configuration Request 70

Room Configuration Response 70

Remove Schedule Request 71

Remove Schedule Response 71

Create Schedule Request 72

Create Schedule Response 72

Room Attribute List Request 73

Query to Change the State of an Attribute(Write) 73

Help Request 75

HelpRequest (Initiation) 75

HelpResponse 75

ii • Contents Reference Guide — 7898E

HelpClose 75

HelpCancel 75

Get OpenIssues 76

Get OpenIssues Response 76

Room Schedule Request for Current/Next Meeting 77

Glossary 78

Appendix A: Filtered Schedule Request Fields 79

Reference Guide — 7898E Contents • iii

iv • Contents Reference Guide — 7898E

Reference Guide — 7898E Crestron Fusion® Software SSI Model • 1

Introduction

SSIcompliant and provides guidelines to programmers that are implementing Crestron

Since the SSIattributes are a standardized set of data that allows Crestron customers to

use built-in reports in Crestron Fusion, it is critical that all applications provide data in a

consistent manner. This document focuses on the application provider and includes all

relevant implementation notes and testing instructions.

The SSImodel provides the following:

2 • Crestron Fusion® Software SSI Model Reference Guide — 7898E

The following reports are included in Crestron Fusion software:

Reference Guide — 7898E Crestron Fusion® Software SSI Model • 3

Behavior:A device is considered in use when it is the current active source in the room and

10 • Crestron Fusion® Software SSI Model Reference Guide — 7898E

Reference Guide — 7898E Crestron Fusion® Software SSI Model • 11

The following should be completed prior to programming with Crestron Fusion

SSImodules:

functionality and features of the Crestron Fusion deployment.

Functional programming is defined as any programming required that automates

the room with control and feedback.

has been completed substantially.

The procedures in this document must be followed in order. Before using these procedures,

review the following SIMPL programming flow diagram.

12 • Crestron Fusion® Software SSI Model Reference Guide — 7898E

To add the Fusion Roomdevice definition in SIMPL:

under Crestron Devices > Ethernet Control Modules > Ethernet based Crestron

Reference Guide — 7898E Crestron Fusion® Software SSI Model • 13

The user can also right-click the Ethernet subslot for the processor and then add the

14 • Crestron Fusion® Software SSI Model Reference Guide — 7898E

To add assets to the FusionRoom device definition in SIMPL:

1. Ensure all prerequisites have been met as described above.

2. Select the Configure view.

3. Right-click the Fusion Room device definition.

4. Select Add Item to Fusion Room. The Select New Device dialog box is displayed.

5. Select Fusion Static Asset from the list.

Select New Device Dialog Box